Heatiator GB4336 Symptom, Possible Causes, Corrective Actions, Pilot sparks, but pilot will

Page 36

 

Symptom

 

Possible Causes

Corrective Actions

4.

Pilot sparks, but pilot will

A.

Correct gas supply.

Verify that incoming gas line ball valve is “open”. Verify that inlet pressure

 

not light.

 

 

reading is within acceptable limits, inlet pressure must not exceed 14 in. w.c.

 

 

B.

Ignitor gap is too large.

Verify that spark gap from ignitor to pilot hood is .17 in. or 1/8 in.

 

 

 

 

 

 

 

C.

Module is not grounded.

Verify module is securely grounded to metal chassis of appliance.

 

 

D.

Module voltage output/

Replace module.

 

 

 

valve/pilot solenoid ohms

 

 

 

 

readings.

 

36

Heatilator • GB4336/GB4992 • 4003-085 Rev H • 04/06

Page 35 Page 37
Image 36
Page 35 Page 37
Contents What to do if you smell gas Models GB4336, GB4336L GB4336I, GB4336ILGB4942, GB4942L GB4942I, GB4942IL B-VentGas ApplianceHomeowner Reference Information Listing Label Information/LocationCongratulations Gas TypeTable of Contents 5 Vent Information and Diagrams8 Installing Vent Pipe 12 Appliance SetupD. High Altitude Installations 1Listing and Code ApprovalsA. Appliance Certification C. BTU SpecificationsA. Design and Installation Considerations 2Getting StartedB. Negative Pressure Negative PressureAsphyxiation Risk C. Tools and Supplies Needed D. Inspect the Appliance and ComponentsAny such action may cause a fire hazard 3Framing and Clearances A. Select Appliance LocationFire Risk B. Construct the Appliance Chase Fire RiskC. Clearances Fire Risk Odor RiskD. Mantel Projections Top of Appliance Drywall A 48 in 1219 mm B maxMantel Leg or Perpendicular Wall A1 in. 25mm min to perpendicular wall4Termination Locations A. Vent Termination Minimum ClearancesFire Risk Explosion Risk 5Vent Information and Diagrams A. Vent GuidelinesB. Vent System Configuration Fire Risk Asphyxiation RiskVent supports Fire Risk Explosion Risk6Vent Clearances and Framing A. Pipe Clearances to CombustiblesB. Wall Penetration Framing C. Vertical Penetration FramingA. Installing Outside Air Kit Damper Assembly Appliance PreparationRisk of Smoke Spillage Fire Risk Asphyxiation RiskB. Gas and Electrical Connections C. Securing and Leveling ApplianceNailing Tabs both sides8Installing Vent Pipe B. Attach Vent to Firebox AssemblyA. Assemble Vent Sections C. Securing Vent Sections9Gas Information A. Fuel ConversionC. Gas Connection B. Gas PressureD. High Altitude Installations Fire Risk Explosion RiskGas build-upduring line purge may ignite Fire Risk Explosion Risk Asphyxiation RiskA. Recommendation for Wire B. Connecting to the ApplianceC. Intellifire Ignition System Wiring 10 Electrical InformationD. Standing Pilot Ignition System Wiring Optional Accessories RequirementsOptional Junction Box Wiring E. Junction Box Installation 11 Finishing A. Mantel ProjectionsB. Facing Material Fire Risk12 Appliance Setup B. Clean the ApplianceC. Accessories D.Install the RefractoryF. Log Removal/Replacement I. Air Shutter Setting G. Glass DoorsH. Hood Fire Risk Combustion Fumes Risk13 Operating Instructions A. Before Lighting ApplianceFire Risk Burn Risk HOT! DO NOT TOUCH SEVERE BURNS MAY RESULTC. High Limit Safety Switch B. Check Appliance DraftNote to Qualified Service Technician WithoutD. Lighting the Appliance WARNING RISK OF FIREFOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONSFOR YOUR SAFETY READ BEFORE LIGHTING NATURAL GASLIGHTING INSTRUCTIONS TO TURN OFF GAS TO APPLIANCEF. Frequently Asked Questions E. After the Appliance is LitInitial Break-inProcedure Issue14 Troubleshooting A. Standing Pilot Ignition SystemSymptom Possible CausesSymptom Possible CausesCorrective Actions Frequent pilot outageB. Intellifire Ignition System SymptomPossible Causes Corrective ActionsSymptom Possible CausesCorrective Actions Pilot sparks, but pilot will15 Maintaining and Servicing the Appliance CleanWhen cleaning glass door Risk of injury or property damageMaintenance and Service Tasks Maintenance TasksInspect one is not presentA. Appliance Dimension Diagram 16 Reference MaterialsFigure 16.1 Appliance Dimensions ModelService Parts B. Service Parts ListGB4336 SERIES Exploded Parts DiagramService Parts GB4336 SERIESDescription of Part GB4336Standing Pilot Valve Assembly Intermittent Pilot Valve AssemblyService Parts Service Parts ListService Parts GB4336 SERIESDescription of Part GB4336GB4942 SERIES Service PartsExploded Parts Diagram Beginning Manufacturing Date 1/19/04Service Parts GB4942 SERIES# Description of Part GB4942Service Parts Standing Pilot Valve AssemblyIntermittent Pilot Valve Assembly Service Parts ListService Parts GB4942 SERIES# Description of Part GB4942C. Optional Components ID4 Insulated Ductin. 102 mm UD4 Uninsulated Duct 4 in. 102 mm 42 in 1067 mmThis page intentionally left blank This page intentionally left blank D. Limited Lifetime Warranty Gas Appliance Fireplace Limited Lifetime WarrantyLimited Lifetime Warranty 1 Year Limited WarrantyE. Contact Information Hearth & Home Technologies Inc1915 W. Saunders Street Mt. Pleasant, Iowa DO NOT DISCARD THIS MANUAL
Top Page Image Contents