Heatiator GB4336 owner manual E. Junction Box Installation

Page 23

E. Junction Box Installation

•Remove the junction box assembly from the valve compartment.

•If the box is being wired from the OUTSIDE of the appliance;

-Loosen two screws on the Romex connector, feed the necessary length of wire through the connector and tighten the screws.

-Make all necessary wire connections to the receptacle and assemble the receptacle and cover to the junction box.

-Attach the junction box assembly to the outside of the appliance with the two screws provided.

•If the box is being wired from the INSIDE of the appliance;

-Pull the electrical wires from outside the appliance through this opening into the valve compartment.

-Loosen the two screws on the Romex connector, feed the necessary length of wire through the connector and tighten the screws.

-Make all necessary wire connections to the receptacle and assemble the receptacle and cover to the junction box.

-Attach the junction box assembly to the inside of the appliance with the two screws provided.

•If the box is not to be wired at the time of appliance installation, assemble the receptacle and cover to the box and install on the inside of the appliance.

Heatilator • GB4336/GB4992 • 4003-085 Rev H • 04/06

23

Image 23

Contents B-VentGas Appliance What to do if you smell gasModels GB4336, GB4336L GB4336I, GB4336IL GB4942, GB4942L GB4942I, GB4942ILGas Type Homeowner Reference InformationListing Label Information/Location Congratulations12 Appliance Setup Table of Contents5 Vent Information and Diagrams 8 Installing Vent PipeC. BTU Speciﬁcations D. High Altitude Installations1Listing and Code Approvals A. Appliance Certiﬁcation2Getting Started A. Design and Installation ConsiderationsAsphyxiation Risk B. Negative PressureNegative Pressure Any such action may cause a ﬁre hazard C. Tools and Supplies NeededD. Inspect the Appliance and Components Fire Risk 3Framing and ClearancesA. Select Appliance Location Fire Risk B. Construct the Appliance ChaseFire Risk Odor Risk C. Clearancesto perpendicular wall D. Mantel ProjectionsTop of Appliance Drywall A 48 in 1219 mm B max Mantel Leg or Perpendicular Wall A1 in. 25mm minFire Risk Explosion Risk 4Termination LocationsA. Vent Termination Minimum Clearances Fire Risk Asphyxiation Risk 5Vent Information and DiagramsA. Vent Guidelines B. Vent System ConﬁgurationFire Risk Explosion Risk Vent supportsC. Vertical Penetration Framing 6Vent Clearances and FramingA. Pipe Clearances to Combustibles B. Wall Penetration FramingFire Risk Asphyxiation Risk A. Installing Outside Air Kit Damper AssemblyAppliance Preparation Risk of Smoke Spillageboth sides B. Gas and Electrical ConnectionsC. Securing and Leveling Appliance Nailing TabsC. Securing Vent Sections 8Installing Vent PipeB. Attach Vent to Firebox Assembly A. Assemble Vent SectionsB. Gas Pressure 9Gas InformationA. Fuel Conversion C. Gas ConnectionFire Risk Explosion Risk Asphyxiation Risk D. High Altitude InstallationsFire Risk Explosion Risk Gas build-upduring line purge may ignite10 Electrical Information A. Recommendation for WireB. Connecting to the Appliance C. Intelliﬁre Ignition System WiringOptional Junction Box Wiring D. Standing Pilot Ignition System WiringOptional Accessories Requirements E. Junction Box Installation Fire Risk 11 FinishingA. Mantel Projections B. Facing MaterialD.Install the Refractory 12 Appliance SetupB. Clean the Appliance C. AccessoriesF. Log Removal/Replacement Fire Risk Combustion Fumes Risk I. Air Shutter SettingG. Glass Doors H. HoodSEVERE BURNS MAY RESULT 13 Operating InstructionsA. Before Lighting Appliance Fire Risk Burn Risk HOT! DO NOT TOUCHWithout C. High Limit Safety SwitchB. Check Appliance Draft Note to Qualiﬁed Service TechnicianLIGHTING INSTRUCTIONS D. Lighting the ApplianceWARNING RISK OF FIRE FOR YOUR SAFETY READ BEFORE LIGHTINGTO TURN OFF GAS TO APPLIANCE FOR YOUR SAFETY READ BEFORE LIGHTINGNATURAL GAS LIGHTING INSTRUCTIONSIssue F. Frequently Asked QuestionsE. After the Appliance is Lit Initial Break-inProcedurePossible Causes 14 TroubleshootingA. Standing Pilot Ignition System SymptomFrequent pilot outage SymptomPossible Causes Corrective ActionsCorrective Actions B. Intelliﬁre Ignition SystemSymptom Possible CausesPilot sparks, but pilot will SymptomPossible Causes Corrective ActionsRisk of injury or property damage 15 Maintaining and Servicing the ApplianceClean When cleaning glass doorone is not present Maintenance and Service TasksMaintenance Tasks InspectModel A. Appliance Dimension Diagram16 Reference Materials Figure 16.1 Appliance DimensionsExploded Parts Diagram Service PartsB. Service Parts List GB4336 SERIESGB4336 Service PartsGB4336 SERIES Description of PartService Parts List Standing Pilot Valve AssemblyIntermittent Pilot Valve Assembly Service PartsGB4336 Service PartsGB4336 SERIES Description of PartBeginning Manufacturing Date 1/19/04 GB4942 SERIESService Parts Exploded Parts DiagramGB4942 Service PartsGB4942 SERIES # Description of PartService Parts List Service PartsStanding Pilot Valve Assembly Intermittent Pilot Valve AssemblyGB4942 Service PartsGB4942 SERIES # Description of PartUD4 Uninsulated Duct 4 in. 102 mm 42 in 1067 mm C. Optional ComponentsID4 Insulated Duct in. 102 mmThis page intentionally left blank This page intentionally left blank 1 Year Limited Warranty D. Limited Lifetime WarrantyGas Appliance Fireplace Limited Lifetime Warranty Limited Lifetime WarrantyDO NOT DISCARD THIS MANUAL E. Contact InformationHearth & Home Technologies Inc 1915 W. Saunders Street Mt. Pleasant, Iowa