Desa CCL3018P, CRL2718P Dual Burner Premium Aged Split Oak Models, Installing Middle Log #2

Page 14

14

INSTALLATION

Installing Logs (Cont.)

INSTALLATION

Continued

2.Place the base of the middle log (#2) in the U-shaped slots of the grate base in front of the back log. The cutout on the right of the middle log should fit over the burner (see Figure 20). Make sure the front of the middle log is resting on the tabs of the grate base and the cutout area is centered over the burner “U” bend.

3.Locate the recesses on the back of the front log (#3). Fit these recesses between the posts of the grate base (see Figure 21).

4.Locate the notches in the bottom of the crossover log (#4). Place the crossover log on top of the middle log and front log. Make sure the notches of the crossover log lines up with rectangular knobs on top of the middle and front logs (see Figure 22).

5.Place lava rock around base of heater if desired. Do not put lava rock on logs on burner.

Middle Log (#2)

Tab

Burner

Cutout

“U” Bend

U-Shaped Slot

Figure 20 - Installing Middle Log (#2)

Front Log (#3)

Recess

Post

Post

Figure 21 - Installing Front Log (#3)

Notches	Crossover Log (#4)

Rectangular

Knobs

Figure 22 - Installing Crossover Log (#4)

Dual Burner Premium Aged Split Oak Models

WARNING: Failure to position the parts in accor- dance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.

1.Place the base of the middle log (#1) in the U-shaped slots of the grate base. The cutout on the right of the middle log should fit over the burner (see Figure 23). Make sure the front of the middle log is resting on the tabs of the grate base and the cut- out area is centered over the burner “U” bend.

Middle Log (#1)

Tab

Burner

“U” Bend

U-Shaped Slot

Figure 23 - Installing Middle Log (#1)

For..com

107124-01E

Image 14

Contents OWNER’S Operation and Installation Manual What to do if YOU Smell GASTable of Contents Safety InformationProduct Identification Unpacking Product Features AIR for Combustion and VentilationLocal Codes Determining if You Have a Confined or Uncon- fined Space Determining FRESH-AIR Flow for Heater LocationConfined and Unconfined Space Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Installation Check GAS TypeIf Using Mantel Minimum Noncombustible Material ClearancesFloor Clearances Determining Minimum Mantel Clearance When Using a HoodMantel Clearances Determining Minimum Mantel ClearanceInstallation Items Needed Installing Damper Clamp Accessory for Vented OperationInstalling Heater Base Assembly Connecting to GAS Supply Attaching Flexible Gas Hose to Heater Gas RegulatorPressure Testing Gas Supply Piping system Checking GAS ConnectionsDual Burner Smoky Mountain Oak Models Installing LogsPressure Testing Heater Gas Connections Installing Middle Log #2 Dual Burner Premium Aged Split Oak ModelsInstalling Front Log #4 Installing Middle Log #2 CCL3930PTA Shown Dual Burner Biltmore Split Oak ModelsInstalling Crossover Log #5 CCL3930PTA Shown Installing Front Log Single Burner Seasonal Oak ModelsLighting Instructions For Your Safety Read Before LightingOperating Heater To Turn OFF GAS to Appliance Manual Lighting ProcedureVariable Control Operation Shutting Off HeaterElectrode Thermocouple Pilot Flame Pattern Inspecting BurnersThermostat Control Operation Burner Primary AIR HolesLogs Cleaning MaintenanceCleaning Burner Injector Holder and Pilot AIR Inlet Hole Troubleshooting Observed Problem Possible Cause RemedyFor more Visit www Com Gas leak. See Warning statement Optional Positioning of Thermostat Sensing Bulb For Masonry and Factory-built Metal FireplaceService Hints Replacement PartsAccessories Technical ServiceSingle Burner Seasonal OAK Models SpecificationsDual Burner Biltmore Split OAK Models Illustrated Parts Breakdown Variable Manually-ControlledParts List CGD3930P, CCL3018P CCL3924PCGD3018PT CGD3924PT CGD3930PT Thermostatically-Controlled Smoky Mountain Oak ModelsCGD3924PT and CGD3930PT CCL3018PT Thermostatically-Controlled Biltmore Split Oak ModelKEY Part Number CCL3018PT Description QTY CCL3924PT CCL3930PTA Thermostatically-Controlled Biltmore Split Oak ModelVariable Manually-Controlled Seasonal Oak Models Seasonal Oak Models Description QTYParts Central Owners Registration Form Postage Required 107124-01E Warranty Information Keep this Warranty