Desa CRL2718P, CRL3124P, CCL3018P, CGD3924P Installing Crossover Log #5 CCL3930PTA Shown

Page 17

INSTALLATION

Installing Logs (Cont.)

17

INSTALLATION

Continued

5.For CCL3924PT and CCL3930PTA Only: Locate pin and hole on the bottom of crossover log (#5). Slide the pin into the hole located in crossover log (#4). Slide the hole onto the pin on front log (#1). See Figure 32.

For CCL3018P and CCL3018PT Only: Locate holes on the bot- tom of crossover log (#5). Slide the holes over the left pins on middle log (#2) and front log (#1). See Figure 33.

6.Locate holes on the bottom of crossover log (#6). Slide these holes onto the right pins located in middle log (#2) and front log (#1). See Figure 34.

7.For CCL3930PTA only: Locate holes on the bottom of cross- over log (#7). Slide onto the pins located in crossover log (#6) and middle log (#2). See Figure 35.

8.Add lava rock around base of heater if desired. Do not place any lava rock on logs or burner.

Crossover Log (#4)

Front Log (#1)

Figure 32 - Installing Crossover Log (#5)

(CCL3930PTA Shown)

Crossover

Log (#4)

Front Log (#1)

Figure 33 - Installing Crossover Log (#5)

(CCL3018P and CCL3018PT Only)

6

Pins

Log #2

Front Log (#1)

Figure 34 - Installing Crossover Log (#6)

(CCL3930PTA Shown)

Holes

7

Crossover

Log (#6)

Middle

Log (#2)

Pins

Figure 35 - Installing Crossover Log (#7) (Model CCL3930PTA Only)

For morevisit www..com

107124-01E

Image 17

Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualSafety Information Table of ContentsProduct Identification Unpacking Product Features AIR for Combustion and VentilationLocal Codes Determining if You Have a Confined or Uncon- fined Space Determining FRESH-AIR Flow for Heater LocationConfined and Unconfined Space Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Check GAS Type InstallationMinimum Noncombustible Material Clearances If Using MantelMantel Clearances Determining Minimum Mantel Clearance When Using a HoodFloor Clearances Determining Minimum Mantel ClearanceInstallation Items Needed Installing Damper Clamp Accessory for Vented OperationInstalling Heater Base Assembly Attaching Flexible Gas Hose to Heater Gas Regulator Connecting to GAS SupplyChecking GAS Connections Pressure Testing Gas Supply Piping systemDual Burner Smoky Mountain Oak Models Installing LogsPressure Testing Heater Gas Connections Dual Burner Premium Aged Split Oak Models Installing Middle Log #2Installing Front Log #4 Dual Burner Biltmore Split Oak Models Installing Middle Log #2 CCL3930PTA ShownInstalling Crossover Log #5 CCL3930PTA Shown Single Burner Seasonal Oak Models Installing Front LogLighting Instructions For Your Safety Read Before LightingOperating Heater Variable Control Operation Manual Lighting ProcedureTo Turn OFF GAS to Appliance Shutting Off HeaterElectrode Thermocouple Thermostat Control Operation Inspecting BurnersPilot Flame Pattern Burner Primary AIR HolesLogs Cleaning MaintenanceCleaning Burner Injector Holder and Pilot AIR Inlet Hole Observed Problem Possible Cause Remedy TroubleshootingFor more Visit www Com Gas leak. See Warning statement For Masonry and Factory-built Metal Fireplace Optional Positioning of Thermostat Sensing BulbAccessories Replacement PartsService Hints Technical ServiceSingle Burner Seasonal OAK Models SpecificationsDual Burner Biltmore Split OAK Models Variable Manually-Controlled Illustrated Parts BreakdownCGD3930P, CCL3018P CCL3924P Parts ListThermostatically-Controlled Smoky Mountain Oak Models CGD3018PT CGD3924PT CGD3930PTCGD3924PT and CGD3930PT Thermostatically-Controlled Biltmore Split Oak Model CCL3018PTKEY Part Number CCL3018PT Description QTY CCL3924PT CCL3930PTA Biltmore Split Oak Model Thermostatically-ControlledVariable Manually-Controlled Seasonal Oak Models Description QTY Seasonal Oak ModelsParts Central Owners Registration Form Postage Required 107124-01E Keep this Warranty Warranty Information