Desa CRL3124P, CRL2718P, CCL3018P Installing Logs, Pressure Testing Heater Gas Connections

Page 13

INSTALLATION

Checking Gas Connections (Cont.) Installing Logs

13

INSTALLATION

Continued

Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)

1.Close equipment shutoff valve (see Figure 17).

2.Pressurize supply piping system by either using compressed air or opening propane/LP supply tank valve.

3.Check all joints from propane/LP supply tank to equipment shutoff valve (see Figure 18). Apply a noncorrosive leak de- tection fluid to all joints. Bubbles forming show a leak.

4.Correct all leaks at once.

INSTALLING LOGS

CAUTION: After installation and periodically there- after, check to ensure that no flame comes in contact with any log. With the heater set to high, check to see if flames contact any log. If so, reposition logs according to the log installation instructions in this manual. Flames contacting logs will create soot.

Pressure Testing Heater Gas Connections

1.

Open equipment shutoff valve (see Figure 17).

2.

Open propane/LP supply tank valve.

3.

Make sure control knob of heater is in the OFF position.

4.

Check all joints from equipment shutoff valve to control valve

 

(see Figure 18). Apply a noncorrosive leak detection fluid to

 

all joints. Bubbles forming show a leak.

5.

Correct all leaks at once.

6.

Light heater (see Operating Heater, pages 19 and 20 [manu-

 

ally-controlled models] or pages 20 and 21 [thermostatically-

 

controlled models]). Check all other internal joints for leaks.

7.

Turn off heater (see To Turn Off Gas to Appliance, page 20

 

[manually-controlled models] or page 21 [thermostatically-con-

Dual Burner Smoky Mountain Oak Models

WARNING: Failure to position the parts in accor- dance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.

1.Locate pins on the bottom of back log (#1). Slide these pins into the holes in the grate base behind the burner (see Figure 19).

trolled models]).

Open

Pin

Back Log (#1)

Equipment

Shutoff

Valve

Closed

Figure 17 - Equipment Shutoff Valve

Hole in Grate Base

Propane/LP Supply Tank

Equipment

Shutoff Valve

Thermostat Gas Valve or

Control Valve Location

Burner

Figure 19 - Installing Back Log (#1)

Figure 18 - Checking Gas Joints

For morevisit www..com

107124-01E

Page 12 Page 14
Image 13
Page 12 Page 14
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualSafety Information Table of ContentsProduct Identification Local Codes Product Features AIR for Combustion and VentilationUnpacking Confined and Unconfined Space Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Uncon- fined Space Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type InstallationMinimum Noncombustible Material Clearances If Using MantelMantel Clearances Determining Minimum Mantel Clearance When Using a HoodFloor Clearances Determining Minimum Mantel ClearanceInstalling Heater Base Assembly Installing Damper Clamp Accessory for Vented OperationInstallation Items Needed Attaching Flexible Gas Hose to Heater Gas Regulator Connecting to GAS SupplyChecking GAS Connections Pressure Testing Gas Supply Piping systemPressure Testing Heater Gas Connections Installing LogsDual Burner Smoky Mountain Oak Models Dual Burner Premium Aged Split Oak Models Installing Middle Log #2Installing Front Log #4 Dual Burner Biltmore Split Oak Models Installing Middle Log #2 CCL3930PTA ShownInstalling Crossover Log #5 CCL3930PTA Shown Single Burner Seasonal Oak Models Installing Front LogOperating Heater For Your Safety Read Before LightingLighting Instructions Variable Control Operation Manual Lighting ProcedureTo Turn OFF GAS to Appliance Shutting Off HeaterElectrode Thermocouple Thermostat Control Operation Inspecting BurnersPilot Flame Pattern Burner Primary AIR HolesCleaning Burner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceLogs Observed Problem Possible Cause Remedy TroubleshootingFor more Visit www Com Gas leak. See Warning statement For Masonry and Factory-built Metal Fireplace Optional Positioning of Thermostat Sensing BulbAccessories Replacement PartsService Hints Technical ServiceDual Burner Biltmore Split OAK Models SpecificationsSingle Burner Seasonal OAK Models Variable Manually-Controlled Illustrated Parts BreakdownCGD3930P, CCL3018P CCL3924P Parts ListThermostatically-Controlled Smoky Mountain Oak Models CGD3018PT CGD3924PT CGD3930PTCGD3924PT and CGD3930PT Thermostatically-Controlled Biltmore Split Oak Model CCL3018PTKEY Part Number CCL3018PT Description QTY CCL3924PT CCL3930PTA Biltmore Split Oak Model Thermostatically-ControlledVariable Manually-Controlled Seasonal Oak Models Description QTY Seasonal Oak ModelsParts Central Owners Registration Form Postage Required 107124-01E Keep this Warranty Warranty Information
Top Page Image Contents