Troubleshooting
Continued
OBSERVED PROBLEM | POSSIBLE CAUSE | REMEDY | ||||
|
|
|
|
|
| |
ODS/pilot lights but flame | 1. Control knob not fully pressed | 1. | Press in control knob fully | |||
goes out when control knob is |
| in | 2. After ODS/pilot lights, keep con- | |||
released | 2. Control knob not pressed in | |||||
|
| 3. | long enough | 3. | trol knob pressed in 30 seconds | |
|
| Safety interlock system has | Wait one minute for safety in- | |||
|
|
| been triggered |
| terlock system to reset. Repeat | |
|
| 4. | Equipment shutoff valve not | 4. | ignition operation | |
|
| Fully open equipment shutoff | ||||
|
| 5. | fully open | 5. | valve | |
|
| Pilot flame not touching ther- | A) Contact local natural or | |||
|
|
| mocouple, which allows ther- |
| propane/LP gas company | |
|
|
| mocouple to cool, causing |
| B) Clean ODS/pilot (see | |
|
|
| pilot flame to go out. This |
| ||
|
|
| problem could be caused by |
| Cleaning and Maintenance, | |
|
|
| one or both of the following: |
| page 24) or replace ODS/pilot | |
|
|
| A) Low gas pressure |
| assembly | |
|
|
| B) Dirty or partially clogged |
|
|
|
|
| 6. | ODS/pilot | 6. | Hand tighten until snug, then | |
|
| Thermocouple connection | ||||
|
| 7. | loose at control valve | 7. | tighten 1/4 turn more | |
|
| Thermocouple damaged | Replace pilot assembly | |||
|
| 8. | Control valve damaged | 8. | Replace control valve | |
|
|
|
|
|
| |
One or both burners do not light | 1. Inlet gas pressure is too low | 1. | Contact local natural or pro- | |||
after ODS/pilot is lit | 2. | Burner orifice(s) clogged | 2. | pane/LP gas company | ||
|
| Clean burner(s) (see Cleaning | ||||
|
|
|
|
| and Maintenance, page 24) or | |
|
| 3. | Mislocated crossover tube | 3. | replace burner orifice(s) | |
|
| Contact qualified service person | ||||
|
| 4. | Remote selector in OFF posi- | 4. | Put remote selector in ON | |
|
| 5. | tion | 5. | position | |
|
| Wire disconnected from gas | See Wiring Diagram, page 23 | |||
|
|
| control |
|
|
|
|
|
|
|
|
| |
Delayed ignition of one or both | 1. Manifold pressure is too low | 1. | Contact local natural or pro- | |||
burners | 2. | Burner orifice(s) clogged | 2. | pane/LP gas company | ||
|
| Clean burner(s) (see Cleaning | ||||
|
|
|
|
| and Maintenance, page 24) or | |
|
| 3. | Mislocated crossover tube | 3. | replace burner orifice(s) | |
|
| Contact qualified service person | ||||
|
|
|
| |||
| Burner backfiring during com- | 1. Burner orifice is clogged or | 1. | Clean burner (see Cleaning |
| |
bustion |
| damaged |
| and Maintenance, page 24) | ||
|
| 2. | Damaged burner | 2. | or replace burner orifice | |
|
| Replace damaged burner | ||||
|
| 3. | Gas regulator defective | 3. | Replace gas regulator | |
|
|
|
|
|
| |
Yellow flame in front burner | 1. Not enough air | 1. | Check burner(s) for dirt | |||
during burner combustion |
|
|
| and debris. If found, clean | ||
|
|
|
|
| burner(s) (see Cleaning and | |
|
| 2. | Gas regulator defective | 2. | Maintenance, page 24) | |
|
| Replace gas regulator | ||||
26 | www.desatech.com |