Quadra-Fire CB1200-B owner manual Alternate Masonry

Page 15

R

CB 1200 Pellet Stove

WARNING

Fire Hazard

Inspection of Chimney:

Masonry chimney must be in good condition.

Meets minimum standard of NFPA 211

Factory-built chimney must be 6 in. (152mm) UL103 HT.

e. Masonry

Concrete Cap

Fireclay Flue

Liner with Airspace

 

 

Flashing

1 in. (25mm) Clearance

 

with Firestop

1 in. (25mm) Clearance

 

 

 in. (76mm) Minimum

6 in. (152mm)

Sheathing

Minimum

 

 

Cleanout Cover

 

Airtight

Non-Combustible Hearth Pad

Clean-out Door

 

Figure 15.1

F. Alternate Masonry

Concrete Cap

Fireclay Flue Liner

with Airspace

 

 

Flashing

1 in. (25mm) Clearance

1 in. (25mm)

with Firestop

Clearance

 

 

2 in. (51mm) Minimum

6 in. (152mm)

 

Minimum

 

 

Sheathing

 

Airtight Clean-out Door

Non-Combustible Hearth Pad

 

Figure 15.2

September 1, 2008

7014-082D

Page 15

Image 15
Contents Hot glass will cause burns Classic BAY 1200 Pellet StoveSerial Number Model Testing Lab & Report NumberCB 1200 Pellet Stove Behind left side curtain on outside of hopper wallTable of Contents Listing and Code Approvals Appliance Location Design, Installation & Location ConsiderationsFire Safety Getting StartedInspect Appliance & Components and Pre-Use Check List CB 1200 Pellet Stove Tools And Supplies NeededAppliance Dimensions Dimensions and ClearancesCB 1200 Pellet Stove Clearances to Combustibles UL and ULC Exception for Horizontal Installations CB 1200 Pellet Stove Hearth Pad Requirements UL and ULCHearth Pad Requirements Vent Information Pipe Selection Chart CB 1200 Pellet Stove Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculaton Alcove 5Venting SystemsStraight Out DegreeCB 1200 Pellet Stove Through The Wall Through The Wall & Vertical CB 1200 Pellet Stove VerticalAlternate Masonry MasonryMobile Home Rear Installation Floor Installation Appliance Set-UpOutside Air Kit Instructions See Figure CB 1200 Pellet Stove Top Vent Adapter InstallationRear Vent and Rear Vent to Top Vent Adapter Installation Installing the Top Vent AdapterBrick Clip Installation CB 1200 Pellet Stove Optional Brick Set InstallationRight Installing Logo Nickel OnlyCharred Areas in the Back Top Log, LeftTo adjust latches Door InstallationCB 1200 Pellet Stove Thermostat Installation To install doorFuel Size And Material General Operating Information Operating InstructionsStarting Your First Fire Feed Rate Adjustment InstructionsCB 1200 Pellet Stove Ignition Cycles Frequently Asked QuestionsTroubleshooting SymptomPossible Cause Corrective Action Page Page Types of Fuel Quick Reference Maintenance Chart10Maintaining & Servicing Your Appliance Frequency Daily Weekly Monthly YearlyAsh Removal from Firebox Cleaning Firepot with Cleaning Rod & Firepot ScraperCleaning Ash Pan Cleaning Heat Exchanger Chambers & Drop TubeCleaning the Hopper Cleaning Beneath Heat ExchangerCleaning Exhaust Path Cleaning the GlassPreparing Firebox for Non-Burn Season Frequency Yearly Cleaning the Top Vent AdapterConvection Blower Replacement CB 1200 Pellet Stove High Ash Fuel Content MaintenanceExhaust Blower Replacement Remove existing blower Install new blowerRe-install blower to blower housing Replacing Side Glass Glass ReplacementComponent Function & Location Reference MaterialsSnap Disc #2 Thermostat Override 200F Vacuum SwitchWiring Harness See .1 below Snap Disc #1 Convection Blower 145FCB 1200 Pellet Stove Component Locations Cleaning Rods Heat Exchanger TubesCB 1200 Pellet Stove Exploded Views Glass Size Center 13-7/8 wide x 11 highGlass Size Sides 8 wide x 11 high Nbr Description CB 1200 Pellet Stove Item # Parts Alphabetical Order CB 1200 Pellet Stove Service Parts and AccessoriesItem # Service Parts Alphabetical Order Appliance AccessoriesDate of Service Performed By Description of Service CB 1200 Pellet Stove Service And Maintenance LogCB 1200 Pellet Stove Homeowner’s Notes CONDITIONS, Exclusions & Limitation of Liability CB 1200 Pellet Stove Warranty PolicyHearth & Home Technologies Limited Warranty Cont’d Contact Information