Quadra-Fire CB1200-B owner manual CB 1200 Pellet Stove Optional Brick Set Installation

Page 19

R

CB 1200 Pellet Stove

D. Optional Brick Set Installation

1.Remove the baffle first, follow instructions on page 33.

2.Slide bottom of left rear brick in first; rotate top edge toward rear of appliance and then rotate outer edge toward rear of appliance, until brick slides into place.

Figure 19.1.

3.Repeat with right rear brick.

4.Place left side brick along left side of firebox, making sure chamfered (beveled) back edge of brick fits snugly next to rear brick. Figure 19.2.

5.Repeat with right side panel.

6.Complete brick set, correctly installed. Figure 19.3.

1

Figure 19.1

E. Brick Clip Installation

WARNING

Risk of Injury.

Brick may have small wires protruding from the back of brick.

1.After the brick set has been installed, 2 brick clips need to be installed on the outer edge of each baffle to hold the brick set in place.

2.Remove 2 baffles from the appliance. Slide the baffle up and the bottom edge should fall down and then lift the baffle out.

3.Using pliers, bend the brick clip slightly past 90° in the direction shown in Figure 19.4.

4.Position the brick clip as shown in Figure 19.4 and use pliers to crimp around the outside edge of the baffle as shown in Figure 19.5.

Note: Figure 19.5 shows the finished shape of the brick clip, after being bent around the outside edge of the baffle.

5.Slide the baffle back into place making sure that the brick clip holds the side brick toward the wall of the firebox. Push back on the sides so they will keep the rear bricks in place. Repeat for opposite side.



1

2

 

 

Figure 19.2



4

1

2

Figure 19.3

 

Approximately

 

1 inch from corner

 

Outside edge

 

of Baffle

Top outside

Use pliers to crimp

corner of Baffle

Brick Clip around edge

 

Figure 19.4

Installed Clip

Figure 19.5

September 1, 2008

7014-082D

Page 19

Image 19
Contents Hot glass will cause burns Classic BAY 1200 Pellet StoveSerial Number Model Testing Lab & Report NumberCB 1200 Pellet Stove Behind left side curtain on outside of hopper wallTable of Contents Listing and Code Approvals Appliance Location Design, Installation & Location ConsiderationsFire Safety Getting StartedInspect Appliance & Components and Pre-Use Check List CB 1200 Pellet Stove Tools And Supplies NeededAppliance Dimensions Dimensions and ClearancesCB 1200 Pellet Stove Clearances to Combustibles UL and ULC CB 1200 Pellet Stove Hearth Pad Requirements UL and ULC Exception for Horizontal InstallationsHearth Pad Requirements Vent Information CB 1200 Pellet Stove Equivalent Feet of Pipe Pipe Selection ChartExample of 3 Elbow-Rear Vent Termination Calculaton Alcove 5Venting SystemsDegree Straight OutCB 1200 Pellet Stove Through The Wall Through The Wall & Vertical CB 1200 Pellet Stove VerticalAlternate Masonry MasonryMobile Home Appliance Set-Up Rear Installation Floor InstallationOutside Air Kit Instructions See Figure CB 1200 Pellet Stove Top Vent Adapter InstallationRear Vent and Rear Vent to Top Vent Adapter Installation Installing the Top Vent AdapterBrick Clip Installation CB 1200 Pellet Stove Optional Brick Set InstallationRight Installing Logo Nickel OnlyCharred Areas in the Back Top Log, LeftTo adjust latches Door InstallationCB 1200 Pellet Stove Thermostat Installation To install doorFuel Size And Material General Operating Information Operating InstructionsStarting Your First Fire Feed Rate Adjustment InstructionsCB 1200 Pellet Stove Ignition Cycles Frequently Asked QuestionsSymptom TroubleshootingPossible Cause Corrective Action Page Page Types of Fuel Quick Reference Maintenance Chart10Maintaining & Servicing Your Appliance Frequency Daily Weekly Monthly YearlyAsh Removal from Firebox Cleaning Firepot with Cleaning Rod & Firepot ScraperCleaning Ash Pan Cleaning Heat Exchanger Chambers & Drop TubeCleaning the Hopper Cleaning Beneath Heat ExchangerCleaning Exhaust Path Cleaning the GlassPreparing Firebox for Non-Burn Season Frequency Yearly Cleaning the Top Vent AdapterConvection Blower Replacement CB 1200 Pellet Stove High Ash Fuel Content MaintenanceInstall new blower Exhaust Blower Replacement Remove existing blowerRe-install blower to blower housing Replacing Side Glass Glass ReplacementComponent Function & Location Reference MaterialsSnap Disc #2 Thermostat Override 200F Vacuum SwitchWiring Harness See .1 below Snap Disc #1 Convection Blower 145FCB 1200 Pellet Stove Component Locations Cleaning Rods Heat Exchanger TubesGlass Size Center 13-7/8 wide x 11 high CB 1200 Pellet Stove Exploded ViewsGlass Size Sides 8 wide x 11 high Nbr Description CB 1200 Pellet Stove Item # Parts Alphabetical Order CB 1200 Pellet Stove Service Parts and AccessoriesItem # Service Parts Alphabetical Order Appliance AccessoriesDate of Service Performed By Description of Service CB 1200 Pellet Stove Service And Maintenance LogCB 1200 Pellet Stove Homeowner’s Notes CONDITIONS, Exclusions & Limitation of Liability CB 1200 Pellet Stove Warranty PolicyHearth & Home Technologies Limited Warranty Cont’d Contact Information