Quadra-Fire 21M-ACC Installing Chimney Components, Single wall connector or stove pipe

Page 16

2100 Millennium Wood Stove (ACC)

R

Solid Pack Chimney with Metal Supports as a Thimble (Cont’d)

C. Installing Chimney Components

Chimney Connector

Single wall connector or stove pipe.

Min. Chimney Clearance to

Wall Spacer and

Combustibles - 2 inch (51mm)

Chimney Flue

Liner

Fireclay

Liner or

Equivalent

Masonry Chimney Constructed to NFPA 211

Min. Clearance 2 inch (51mm)

1 inch (25mm) Air Space to Chimney Section

Chimney

Connector

Chimney Section

Trim Collar

Wall Band

Wall Spacer

This must be at least 24 gauge mild steel or 26 gauge blue steel. The sections must be attached to the appliance and to each other with the crimped (male) end pointing toward the stove. All joints, including the connection at the flue collar, should be secured with 3 sheet metal screws. Make sure to follow the minimum clearances to combustibles. Where passage through the wall, or partition of combustible con- struction is desired in Canada, the installation shall conform to CAN/CSA-B365.

Factory-built listed chimney connector (vented).

A listed connector (vented) must be used when installing this unit in a mobile home. The listed connectors must conform to each other to ensure a proper fit and seal.

Figure 16.1

Chimney Height / Rise and Run

This product was designed for and tested on a 6 inch (152mm) chimney, 14 to 16 feet (420-480cm) high, (includes stove height) measured from the base of the appliance. The further your stack height or diameter varies from this configuration, the possibility of performance problems exists.

Chimney height may need to be increased by 2 - 3% per each 1000 feet above sea level. It is not recommended to use offsets or elbows at altitudes above 4000 feet above sea level or when there are other factors that affect flue draft.

Crimped

Flue Gas

End

Direction

Toward

 

Stove

 

Secure pipe sections with a

minimum of 3 screws

Figure 16.2 Chimney Connector (Stove Pipe)

WARNING

Fire Risk.

Inspection of Chimney:

•Chimney must be in good condition.

•Meets minimum standard of NFPA 211

•Factory-built chimney must be 6 inch (152mm) UL103 HT.

WARNING

Asphyxiation Risk.

•DO NOT CONNECT THIS UNIT TO A CHIM- NEY FLUE SERVICING ANOTHER APPLI- ANCE.

•DO NOT CONNECT TO ANY AIR DISTRI- BUTION DUCT OR SYSTEM.

May allow flue gases to enter the house.

WARNING

Fire Risk.

Follow Chimney Connector Manufacturer’s

Instructions for Proper Installation.

ONLY use connector:

•Within the room, between appliance and ceiling or wall. Connector shall NOT pass through:

•Attic or roof space

•Closet or similar concealed space

•Floor or ceiling

Maintain minimum clearances to combustibles

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appli- ance. For assistance or additional information consult a qualified installer, service agency or your dealer.

Page 16

7039-131H

May 5, 2011

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Hot glass will cause burns 7039-131H May 5Serial No Model Name Test Lab & Report No Millennium Wood Stove ACCMfg. Date 7039-131H May 5 Table of Contents Appliance Certification BTU & Efficiency Specifications Glass SpecificationsListing and Code Approvals Mobile Home ApprovedFire Safety Getting StartedAppliance needs to draft properly for safety Millennium Wood Stove ACC Negative PressureMillennium Wood Stove ACC Flue Draft Considerations Venting SystemsTools And Supplies Needed Inspect Appliance & Components Pre-Burn Check ListMillennium Wood Stove ACC Typical Stove Systems Masonry ChimneyDimensions and Clearances Appliance DimensionsBackwall / Sidewall Corner Installation InstallationR Hearth Protection RequirementsSee Figure USA required Canada recommendedItems Needed for Installation not supplied Millennium Wood Stove ACC Outside Air Kit InstallationFloor Installation Alternative In some instances you Blower Optional 13-15/16 in mmChimney Connector Chimney RequirementsVenting Components Chimney Systems ThimbleComponents Air ClearancesInstructions Solid Pack Chimney with Metal Supports as a ThimbleInstalling Chimney Components Single wall connector or stove pipeSolid Pack Chimney with Metal Supports as a Thimble Cont’d Chimney Height / Rise and RunMillennium Wood Stove ACC Chimney Termination Requirements RulePitched Roof Flat RoofMobile Home Installation Door Handle Assembly Adjusting The Blower Speed Control Appliance Set-UpOperating Instructions Over-Firing Your Appliance Wood Selection & Storage Cont’dBurning Process Wood Selection & StorageAutomatic Combustion Control ACC Air ControlsBurn Rates and Operating Efficiency Millennium Wood Stove ACC Building a Fire Incorrect Positions Initial cold start-up and all Burn Settings Millennium Wood Stove ACC Blower Operating InstructionsOpacity Smoke Snap Disc LocationOdor from appliance Millennium Wood Stove ACC Frequently Asked QuestionsAppliance Quick Reference Maintenance Guide Maintaining & Servicing Your ApplianceMillennium Wood Stove ACC General Maintenance Creosote Chimney CleaningGlass Cleaning Frequency As desired Disposal of AshesGlass Replacement When cleaning glassMillennium Wood Stove ACC Firebrick Replacement To your authorized dealerCorrect Blanket & Baffle Position on BaffleRemoving Tube Channel Assembly Millennium Wood Stove ACC Tube Channel Assembly ReplacementReplacing Tube Channel Assembly Troubleshooting Start Fire Problems Possible Cause Solution21M-ACC Millennium Wood Stove21M-ACC Stocked 21M-ACC Millennium Wood Stove ACC Service And Maintenance Log Date of Service Performed By Description of ServiceMillennium Wood Stove ACC Service And Maintenance Log Cont’d Millennium Wood Stove ACC Homeowner’s Notes Millennium Wood Stove ACC Homeowner’s Notes Millennium Wood Stove ACC Warranty Policy Millennium Wood Stove ACC Contact Information
Top Page Image Contents