Quadra-Fire 7051-158B Soft Start Cycle SS-Low / SS-Med, Auto-Clean Cycle, Automatic Mode

Page 11

R

EDGE 60 Pellet Fireplace

2.Soft Start Cycle (SS-Low / SS-Med)

Once the fi re is lit:

•The appliance moves into the low soft-start cycle as it continues to build the fi re

•More fuel will be added

•As the fi re builds, the appliance will change to medium soft-start mode

•The heating cycle begins

5.Auto-Clean Cycle

The fi repot auto-clean system will cycle:

•When the appliance is fi rst plugged in

•When the house reaches temperature and the appliance shuts down

•At prescribed intervals, depending on the type of fuel se- lected

•When starting up after an electrical interruption

3. Heating Cycle ( Auto / Man - L, ML, M, MH, H)

There are two choices in the Automatic / Manual menu of how your appliance will operate:

Automatic Mode

•The wall control will turn the heat output level up or down depending on how far the room temperature is from the desired temperature

•The digital display will read AUTO:M, i.e. automatic-me- dium level

•As the room temperature approaches the desired tem- perature, the appliance will turn down to lower settings

•When the home reaches your set temperature, the appli- ance will go into the shutdown cycle

Manual Mode

•Set the heat output setting from the main screen

•The right bottom button will read HEAT OUTPUT

•You can operate the appliance from any of the 5 levels

•On the lowest level (MAN: L) the appliance will stay on longer, burn less fuel per hour, and will take longer to bring the home up to your desired temperature

•On the highest setting (MAN:H) the appliance will burn more fuel per hour, and bring your home up to tempera- ture more quickly

•In Manual mode the heat output does not change but will stay at the setting you chose until the comfort level is reached (meaning the thermostat has been satisfi ed). Turn to OFF to stop operation.

4.Shutdown Cycle

Once your home has reached your set temperature:

•Appliance will stop feeding fuel and allow the fi re to dimin- ish

•Convection blower will continue to run until the appliance cools to appropriate temperature

•Appliance will begin the auto-clean cycle

If your appliance is running and the auto-clean cycle is initi- ated, the appliance will revert to shutdown cycle.

•The fl oor of the fi repot will open and dump the ash into the ash pan

•It takes approximately 2 minutes to complete the auto- clean cycle

•The fl oor will then shut, and if the thermostat is still call- ing for heat, the fi re will start again

•During this auto-clean cycle, the convection blower may continue to run. The combustion blower will continue to run.

Additional Screen Messages:

READY It is telling you that the home is up to temperature and doesn’t need any heat.

-- - - - The screen will show 5 dashes when the wall control and the control board are NOT communicating with each other. Check that the wiring on the thermostat is prop- erly connected.

MAINTENANCE BURN This indicates the appliance is operating on battery backup, prior to the auto-clean. The maintenance burn will keep the system from shutting down as the appliance will not automatically re-light in battery back-up mode.

OFF The AUTO/MANUAL SETTING screen has been set to OFF. Set the appliance to OFF when performing periodic maintenance to prevent an unexpected startup.

BLANK SCREEN The ON/OFF switch may in OFF posi- tion. Turn to ON position.

CAUTION

Tested and approved for wood pellets, shelled fi eld corn, wheat and black oil sunfl ower seeds. Burning of any other type of fuel voids your warranty.

December 6, 2011

7051-158B

Page 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Hot glass will cause burns Natural Curved Tuscan StudioSerial Number Label Edge 60 Pellet FireplaceTable of Contents Edge 60 Pellet Fireplace Edge 60 Pellet Fireplace Listing and Code Approvals Operating Instructions User’s GuideFuel Material and Fuel Storage Edge 60 Pellet Fireplace Fire SafetyCombustible/Non-Combustible Materials Before Your First Fire Power SwitchAuto-Clean Firepot System General Operating InformationIgnition Cycles Edge 60 Pellet Fireplace Filling the Hopper with FuelStarting Your First Fire Soft Start Cycle SS-Low / SS-Med Auto-Clean CycleAutomatic Mode Manual ModeBattery Back-up System Optional Clear Space Edge 60 Pellet Fireplace Battery Back-up System Cont’dBefore Servicing Your Appliance Quick Reference Maintenance ChartCleaning or Inspection Maintaining & Servicing Your ApplianceEdge 60 Pellet Fireplace High Ash Fuel Content Maintenance Accessing Components for MaintenanceDisposal of Ashes Frequency As needed Auto-Clean System Inspection & CleaningCleaning Ash Pan Shop Vac* Example Micro Cleaning Kit Cleaning Heat Exchanger, Drop Tube & ExhaustClinker Cleaning Exhaust Blower Do Not Use Lubrication Cleaning the HopperCleaning Convection Blower Do Not Use Lubrication Cleaning the GlassChimney Inspection and Cleaning Frequently Asked Questions Troubleshooting for HomeownerPossible Cause Corrective Action Floor Support Getting StartedAppliance Location Description Checklist to Help Determine LocationTools And Supplies Needed Inspect Appliance and ComponentsRecommended Sequence Material is installed. See Item GCrush Hazard Hearth Extension Framing Dimensions & ClearancesOutside Air Kit is Required for All installations Recommended LocationsFrame the Fireplace Sealing at the Penetration of Building Envelope27.1 Edge 60 Pellet Fireplace Construct the ChaseProtrudes Beyond the Mounting Frame Edge 60 Pellet Fireplace Finishing MaterialFlush with the Mounting Frame Behind the Mounting FrameOpening Clearances for the Curved Tuscan and Natural Fronts Opening Clearances for the Studio Front Rise to run ratio Edge 60 Pellet Fireplace Mantel Fuel Loading ClearancesCombustible Materials Edge 60 Pellet Fireplace Non-Combustible MaterialsSub-Floor Material & Securing Fireplace Crush Hazard Installation of FireplacePosition the Fireplace Shock Hazard Power Supply Cord Wall Control WireBack Side of Wall Control with Cover Off Vertical InstallationVertical Installation Cont’d Horizontal Installation Termination must exhaust above air inlet elevation Vent InformationVenting Termination Minimum Requirements Do not Terminate VentEdge 60 Pellet Fireplace Avoiding Smoke and Odors Edge 60 Pellet Fireplace Negative Pressure Draft Example of 3 Elbow-Rear Vent Termination Calculation Edge 60 Pellet Fireplace Chimney and Exhaust ConnectionEquivalent Feet of Pipe Altitude in Thousands of Feet Edge 60 Pellet Fireplace Pipe Selection ChartOutside Air Inlet Locations Left Rear Corner Right Rear Corner Rear of FireplaceInstall Outside Air Kit Edge 60 Pellet Fireplace Outside Air Kit InstallationThrough the Wall & Vertical Exterior Vertical Interior Typical InstallationDegree Choose which one is best for your installationEdge 60 Pellet Fireplace Through the Wall Straight OutMobile Home Installation Rebox. Figures 47.3 Optional Log Set Placement InstructionsAppliance Set-Up Rebox. Figures 47.1Front Installation Glass Replacement Replacement PartsConvection Blower Replacement Baffl e Removal & Replacement Error Message Troubleshooting For InstallersRear View Fireplace DimensionsReference Materials Top ViewEdge 60 Pellet Fireplace Component Functions Overheat Sensor Snap Disc Power SupplyPower Switch Vacuum SwitchView of Left Rear Edge 60 Pellet Fireplace Component LocationsDate of Service Performed By Description of Service Edge 60 Pellet Fireplace Service And Maintenance LogHearth & Home Technologies Contact Information

7051-158B specifications

The Quadra-Fire 7051-158B is a premier wood-burning fireplace designed for homeowners seeking an efficient and aesthetically pleasing heating solution. This fireplace combines advanced technology with classic design, making it an exceptional choice for any living space.

One of the key features of the 7051-158B is its impressive heating capability. With a maximum heat output of up to 75,000 BTUs, it can effectively warm areas up to 2,500 square feet. This makes it ideal for both large homes and open-concept areas. The fireplace is equipped with a large firebox that can accommodate logs up to 24 inches, allowing for longer burn times and fewer reloads, thereby enhancing convenience for users.

Efficiency is a major focus of the Quadra-Fire 7051-158B. The unit boasts an impressive EPA-certified efficiency rating, which signifies that it burns wood cleanly and effectively, producing minimal smoke and emissions. This not only benefits the environment but also maximizes the warmth generated from each log of wood burned. The unit is designed to maintain a consistent temperature with its advanced combustion technology, which ensures a clean burn while maximizing heat output.

To enhance user experience, the 7051-158B incorporates several technological features. One such innovation is the Quadra-Fire's patented Four-Point Burn Technology, which promotes optimal airflow and combustion. This technology results in a more complete burn, reducing the amount of creosote buildup in the chimney and enhancing safety. The fireplace also comes with an easy-to-use air control system, allowing homeowners to easily adjust the amount of air entering the firebox for customized heat and burn rates.

From a design perspective, the Quadra-Fire 7051-158B offers a perfect blend of traditional and contemporary aesthetics. The elegant exterior is available in various finishes, enabling homeowners to choose an option that complements their decor. Large glass doors provide a captivating view of the flames, creating a cozy ambiance in any room.

In conclusion, the Quadra-Fire 7051-158B stands out as a top choice for wood-burning fireplaces. With its efficient heating capabilities, cutting-edge technology, and beautiful design, it is sure to enhance both the comfort and appeal of your home. Whether you are looking to heat a large space or simply enjoy the warmth of a wood fire, this fireplace provides a reliable and stylish solution.
Top Page Image Contents