Quadra-Fire 7051-158B owner manual Getting Started, Appliance Location, Floor Support

Page 23

R

EDGE 60 Pellet Fireplace

Installer’s Guide

5 Getting Started

A.Design, Installation & Location Considerations

1.Appliance Location

NOTICE: Contact local building or fire officials about restrictions and installation inspection requirements in your area.

Installation MUST comply with local, regional, state and national codes and regulations.

Consult insurance carrier, local building inspector, fi re offi cials or authorities having jurisdiction over restrictions, installation inspection and permits.

It is a good idea to plan your installation on paper, using exact measurements for clearances and fl oor protection, before actually beginning the installation. Location of the appliance and chimney will affect performance.

Consideration must be given to:

Safety, convenience, traffi c fl ow

Placement of the chimney and chimney connector and to minimize the use of chimney offsets.

Place the appliance where there will be a clear passage for a Listed chimney through the ceiling and roof (verti- cal) or through exterior wall (horizontal).

Installing the required outside air kit will affect the loca- tion of the vent termination.

When locating vent and venting termination, the ideal loca-

tion is to vent above roof line when possible. This mini- mizes the affects of wind loading.

Since pellet exhaust can contain ash, soot or sparks, you must consider the location of:

Windows

Air Intakes

Air Conditioner

Overhang, soffi ts, porch roofs, adjacent walls

Landscaping, vegetation

Horizontal or vertical vent termination

2.Floor Support

The supporting fl oor under the appliance must be able to handle the weight of the fi replace, fuel load and the weight of the chimney.

Ensure that your fl oor will suport these weights prior to in- stallation. Add suffi cient additional support to meet this weight requirment prior to installation. The weight of the

replace is 450 lbs and with a full hopper of fuel weighing 120 lbs, the total for the fi replace and fuel is 570 lbs.

WARNING! Risk of Fire Damaged parts could impair safe operation. Do NOT install damaged, incomplete or substitute components.

CAUTION! If burning shelled fi eld corn, you must use ap- proved venting specifi cally designed for corn to prevent corrosion or degradation. Follow the instructions from the venting manufacturer.

 

Recommended Location:

Recommended Location:

Above peak

• Above peak

Inside heated space

Location NOT recommended:

Not the highest point of the roof

Wind loading possible

Windward

Marginal Location:

• Below peak

Recommended:

Insulated exterior chase in cooler climates

Marginal Location:

• Wind loading possible

Location NOT recommended:

• Too close to tree

• Below adjacent structure

• Lower roof line

• Avoid outside wall

Leeward

Recommended: Outside Air Intake on windward side

Multi-level Roofs

NOT recommended: Outside Air Intake on leeward side

Figure 22.1

December 6, 2011

7051-158B

Page 23

Image 23
Contents Hot glass will cause burns Natural Curved Tuscan StudioSerial Number Label Edge 60 Pellet FireplaceTable of Contents Edge 60 Pellet Fireplace Edge 60 Pellet Fireplace Listing and Code Approvals Operating Instructions User’s GuideFuel Material and Fuel Storage Edge 60 Pellet Fireplace Fire SafetyCombustible/Non-Combustible Materials Before Your First Fire Power SwitchAuto-Clean Firepot System General Operating InformationIgnition Cycles Edge 60 Pellet Fireplace Filling the Hopper with FuelStarting Your First Fire Soft Start Cycle SS-Low / SS-Med Auto-Clean CycleAutomatic Mode Manual ModeBattery Back-up System Optional Clear Space Edge 60 Pellet Fireplace Battery Back-up System Cont’dBefore Servicing Your Appliance Quick Reference Maintenance ChartCleaning or Inspection Maintaining & Servicing Your ApplianceEdge 60 Pellet Fireplace High Ash Fuel Content Maintenance Accessing Components for MaintenanceDisposal of Ashes Frequency As needed Auto-Clean System Inspection & CleaningCleaning Ash Pan Shop Vac* Example Micro Cleaning Kit Cleaning Heat Exchanger, Drop Tube & ExhaustClinker Cleaning Exhaust Blower Do Not Use Lubrication Cleaning the HopperCleaning Convection Blower Do Not Use Lubrication Cleaning the GlassChimney Inspection and Cleaning Frequently Asked Questions Troubleshooting for HomeownerPossible Cause Corrective Action Floor Support Getting StartedAppliance Location Description Checklist to Help Determine LocationTools And Supplies Needed Inspect Appliance and ComponentsRecommended Sequence Material is installed. See Item GCrush Hazard Hearth Extension Framing Dimensions & ClearancesOutside Air Kit is Required for All installations Recommended LocationsFrame the Fireplace Sealing at the Penetration of Building Envelope27.1 Edge 60 Pellet Fireplace Construct the ChaseProtrudes Beyond the Mounting Frame Edge 60 Pellet Fireplace Finishing MaterialFlush with the Mounting Frame Behind the Mounting FrameOpening Clearances for the Curved Tuscan and Natural Fronts Opening Clearances for the Studio Front Rise to run ratio Edge 60 Pellet Fireplace Mantel Fuel Loading ClearancesCombustible Materials Edge 60 Pellet Fireplace Non-Combustible MaterialsSub-Floor Material & Securing Fireplace Crush Hazard Installation of FireplacePosition the Fireplace Shock Hazard Power Supply Cord Wall Control WireBack Side of Wall Control with Cover Off Vertical InstallationVertical Installation Cont’d Horizontal Installation Termination must exhaust above air inlet elevation Vent InformationVenting Termination Minimum Requirements Do not Terminate VentEdge 60 Pellet Fireplace Avoiding Smoke and Odors Edge 60 Pellet Fireplace Negative Pressure Draft Example of 3 Elbow-Rear Vent Termination Calculation Edge 60 Pellet Fireplace Chimney and Exhaust ConnectionEquivalent Feet of Pipe Altitude in Thousands of Feet Edge 60 Pellet Fireplace Pipe Selection ChartOutside Air Inlet Locations Left Rear Corner Right Rear Corner Rear of FireplaceInstall Outside Air Kit Edge 60 Pellet Fireplace Outside Air Kit InstallationThrough the Wall & Vertical Exterior Vertical Interior Typical InstallationDegree Choose which one is best for your installationEdge 60 Pellet Fireplace Through the Wall Straight OutMobile Home Installation Rebox. Figures 47.3 Optional Log Set Placement InstructionsAppliance Set-Up Rebox. Figures 47.1Front Installation Glass Replacement Replacement PartsConvection Blower Replacement Baffl e Removal & Replacement Error Message Troubleshooting For InstallersRear View Fireplace DimensionsReference Materials Top ViewEdge 60 Pellet Fireplace Component Functions Overheat Sensor Snap Disc Power SupplyPower Switch Vacuum SwitchView of Left Rear Edge 60 Pellet Fireplace Component LocationsDate of Service Performed By Description of Service Edge 60 Pellet Fireplace Service And Maintenance LogHearth & Home Technologies Contact Information

7051-158B specifications

The Quadra-Fire 7051-158B is a premier wood-burning fireplace designed for homeowners seeking an efficient and aesthetically pleasing heating solution. This fireplace combines advanced technology with classic design, making it an exceptional choice for any living space.

One of the key features of the 7051-158B is its impressive heating capability. With a maximum heat output of up to 75,000 BTUs, it can effectively warm areas up to 2,500 square feet. This makes it ideal for both large homes and open-concept areas. The fireplace is equipped with a large firebox that can accommodate logs up to 24 inches, allowing for longer burn times and fewer reloads, thereby enhancing convenience for users.

Efficiency is a major focus of the Quadra-Fire 7051-158B. The unit boasts an impressive EPA-certified efficiency rating, which signifies that it burns wood cleanly and effectively, producing minimal smoke and emissions. This not only benefits the environment but also maximizes the warmth generated from each log of wood burned. The unit is designed to maintain a consistent temperature with its advanced combustion technology, which ensures a clean burn while maximizing heat output.

To enhance user experience, the 7051-158B incorporates several technological features. One such innovation is the Quadra-Fire's patented Four-Point Burn Technology, which promotes optimal airflow and combustion. This technology results in a more complete burn, reducing the amount of creosote buildup in the chimney and enhancing safety. The fireplace also comes with an easy-to-use air control system, allowing homeowners to easily adjust the amount of air entering the firebox for customized heat and burn rates.

From a design perspective, the Quadra-Fire 7051-158B offers a perfect blend of traditional and contemporary aesthetics. The elegant exterior is available in various finishes, enabling homeowners to choose an option that complements their decor. Large glass doors provide a captivating view of the flames, creating a cozy ambiance in any room.

In conclusion, the Quadra-Fire 7051-158B stands out as a top choice for wood-burning fireplaces. With its efficient heating capabilities, cutting-edge technology, and beautiful design, it is sure to enhance both the comfort and appeal of your home. Whether you are looking to heat a large space or simply enjoy the warmth of a wood fire, this fireplace provides a reliable and stylish solution.