Quadra-Fire 7051-158B owner manual Edge 60 Pellet Fireplace Through the Wall, Straight Out, Degree

Page 46

R

EDGE 60 Pellet Fireplace

L. Through the Wall

Horizontal termination cap must be a minimum of 12 inches (305mm) from the wall. Approved for mobile home installations. Must use 3 or 4 inch (76mm-102mm) “L” or “PL” Listed pellet venting and a Quadra-Fire Outside Air Kit in ALL installations.

NOTE:

In Canada, where passage through a wall or partition of combustible construction is desired, the installation shall conform to CAN/CSA-B365

Straight Out

0 in. (0mm) to Standoff

6in.

(152mm) Minimum

From Glass

Horizontal

Wall Termination

Thimble Cap

12 in. (305mm) Minimum

Non-combustible

Hearth Extension

Figure 45.1

NOTICE! See Section 8 “Avoiding Smoke and Odors” to minimize soot damage to exterior walls of the house and to prevent re-entry of soot or ash into the house for horizontal vent confi guration

45 Degree

Illustration shows venting going in both directions.

 

Choose which one is best for your installation.

12 IN. (305MM)

MINIMUM

WALL

THIMBLE

12 IN. (305MM)

MINIMUM

1-1/6 IN.( 27MM)

MINIMUM

1-16 IN.

(27MM)

MINIMUM

Figure 45.2

Page 46

7051-158B

December 6, 2011

Image 46
Contents Natural Curved Tuscan Studio Hot glass will cause burnsEdge 60 Pellet Fireplace Serial Number LabelTable of Contents Edge 60 Pellet Fireplace Edge 60 Pellet Fireplace Listing and Code Approvals User’s Guide Operating InstructionsCombustible/Non-Combustible Materials Edge 60 Pellet Fireplace Fire SafetyFuel Material and Fuel Storage General Operating Information Power SwitchAuto-Clean Firepot System Before Your First FireStarting Your First Fire Edge 60 Pellet Fireplace Filling the Hopper with FuelIgnition Cycles Manual Mode Auto-Clean CycleAutomatic Mode Soft Start Cycle SS-Low / SS-MedBattery Back-up System Optional Edge 60 Pellet Fireplace Battery Back-up System Cont’d Clear SpaceMaintaining & Servicing Your Appliance Quick Reference Maintenance ChartCleaning or Inspection Before Servicing Your ApplianceAccessing Components for Maintenance Edge 60 Pellet Fireplace High Ash Fuel Content MaintenanceCleaning Ash Pan Auto-Clean System Inspection & CleaningDisposal of Ashes Frequency As needed Cleaning Heat Exchanger, Drop Tube & Exhaust Shop Vac* Example Micro Cleaning KitClinker Cleaning the Glass Cleaning the HopperCleaning Convection Blower Do Not Use Lubrication Cleaning Exhaust Blower Do Not Use LubricationChimney Inspection and Cleaning Troubleshooting for Homeowner Frequently Asked QuestionsPossible Cause Corrective Action Appliance Location Getting StartedFloor Support Inspect Appliance and Components Checklist to Help Determine LocationTools And Supplies Needed DescriptionCrush Hazard Material is installed. See Item GRecommended Sequence Recommended Locations Framing Dimensions & ClearancesOutside Air Kit is Required for All installations Hearth ExtensionSealing at the Penetration of Building Envelope Frame the FireplaceEdge 60 Pellet Fireplace Construct the Chase 27.1Behind the Mounting Frame Edge 60 Pellet Fireplace Finishing MaterialFlush with the Mounting Frame Protrudes Beyond the Mounting FrameOpening Clearances for the Curved Tuscan and Natural Fronts Opening Clearances for the Studio Front Edge 60 Pellet Fireplace Mantel Fuel Loading Clearances Rise to run ratioEdge 60 Pellet Fireplace Non-Combustible Materials Combustible MaterialsPosition the Fireplace Installation of FireplaceSub-Floor Material & Securing Fireplace Crush Hazard Power Supply Cord Wall Control Wire Shock HazardVertical Installation Back Side of Wall Control with Cover OffVertical Installation Cont’d Horizontal Installation Do not Terminate Vent Vent InformationVenting Termination Minimum Requirements Termination must exhaust above air inlet elevationEdge 60 Pellet Fireplace Avoiding Smoke and Odors Edge 60 Pellet Fireplace Negative Pressure Draft Equivalent Feet of Pipe Edge 60 Pellet Fireplace Chimney and Exhaust ConnectionExample of 3 Elbow-Rear Vent Termination Calculation Edge 60 Pellet Fireplace Pipe Selection Chart Altitude in Thousands of FeetLeft Rear Corner Right Rear Corner Rear of Fireplace Outside Air Inlet LocationsEdge 60 Pellet Fireplace Outside Air Kit Installation Install Outside Air KitVertical Interior Typical Installation Through the Wall & Vertical ExteriorStraight Out Choose which one is best for your installationEdge 60 Pellet Fireplace Through the Wall DegreeMobile Home Installation Rebox. Figures 47.1 Optional Log Set Placement InstructionsAppliance Set-Up Rebox. Figures 47.3Front Installation Replacement Parts Glass ReplacementConvection Blower Replacement Baffl e Removal & Replacement Troubleshooting For Installers Error MessageTop View Fireplace DimensionsReference Materials Rear ViewEdge 60 Pellet Fireplace Component Functions Vacuum Switch Power SupplyPower Switch Overheat Sensor Snap DiscEdge 60 Pellet Fireplace Component Locations View of Left RearEdge 60 Pellet Fireplace Service And Maintenance Log Date of Service Performed By Description of ServiceContact Information Hearth & Home Technologies

7051-158B specifications

The Quadra-Fire 7051-158B is a premier wood-burning fireplace designed for homeowners seeking an efficient and aesthetically pleasing heating solution. This fireplace combines advanced technology with classic design, making it an exceptional choice for any living space.

One of the key features of the 7051-158B is its impressive heating capability. With a maximum heat output of up to 75,000 BTUs, it can effectively warm areas up to 2,500 square feet. This makes it ideal for both large homes and open-concept areas. The fireplace is equipped with a large firebox that can accommodate logs up to 24 inches, allowing for longer burn times and fewer reloads, thereby enhancing convenience for users.

Efficiency is a major focus of the Quadra-Fire 7051-158B. The unit boasts an impressive EPA-certified efficiency rating, which signifies that it burns wood cleanly and effectively, producing minimal smoke and emissions. This not only benefits the environment but also maximizes the warmth generated from each log of wood burned. The unit is designed to maintain a consistent temperature with its advanced combustion technology, which ensures a clean burn while maximizing heat output.

To enhance user experience, the 7051-158B incorporates several technological features. One such innovation is the Quadra-Fire's patented Four-Point Burn Technology, which promotes optimal airflow and combustion. This technology results in a more complete burn, reducing the amount of creosote buildup in the chimney and enhancing safety. The fireplace also comes with an easy-to-use air control system, allowing homeowners to easily adjust the amount of air entering the firebox for customized heat and burn rates.

From a design perspective, the Quadra-Fire 7051-158B offers a perfect blend of traditional and contemporary aesthetics. The elegant exterior is available in various finishes, enabling homeowners to choose an option that complements their decor. Large glass doors provide a captivating view of the flames, creating a cozy ambiance in any room.

In conclusion, the Quadra-Fire 7051-158B stands out as a top choice for wood-burning fireplaces. With its efficient heating capabilities, cutting-edge technology, and beautiful design, it is sure to enhance both the comfort and appeal of your home. Whether you are looking to heat a large space or simply enjoy the warmth of a wood fire, this fireplace provides a reliable and stylish solution.