Quadra-Fire 7051-158B owner manual Replacement Parts, Glass Replacement

Page 50

R

EDGE 60 Pellet Fireplace

11 Replacement Parts

A. Glass Replacement

WARNING! Risk of Injury!

•Glass is 5mm thick high temperature heat-resistant ceramic glass.

•DO NOT REPLACE with any other material.

•Alternate material may shatter and cause injury

1.To remove the door:

a.Swing open the front.

b.Remove the door by lifting it off the hinge pins.

c.Lay on a fl at surface face down.

2.Using a Phillips head screwdriver, remove 4 screws, 2 on the top and 2 on the bottom. Figure 49.1.

3.Remove metal bracket.

4.Remove the glass.

5.Replace with new glass with gasket.

6.Re-attach metal bracket with 4 screws.

7.Re-install door over hinge pins and close front.

Remove 4 screws

Metal Bracket

Glass with Gasket

Figure 49.1

B.Combustion (Exhaust) Blower Replacement

1.Follow the proper shut down procedures as outlined on page 14, Section 3.A

2.The combustion blower is mounted in the lower right rear of the appliance. Figure 49.2.

3.Use an 11/32 nut driver to loosen all six nuts, but do not remove. Rotate the blower and remove from the housing. Figure 49.3.

4.Disconnect the wires.

5.You will also need to replace the gasket, see Parts List for part number.

6.Install replacement blower in reverse order and re-con- nect the wires.

Combustion Blower Located

Right Lower Side of Fireplace

Combustion Blower

Figure 49.2

LOOSEN ALL 6 NUTS, BUT DO NOT REMOVE

Figure 49.3

Page 50

7051-158B

December 6, 2011

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Natural Curved Tuscan Studio Hot glass will cause burnsEdge 60 Pellet Fireplace Serial Number LabelTable of Contents Edge 60 Pellet Fireplace Edge 60 Pellet Fireplace Listing and Code Approvals User’s Guide Operating InstructionsFuel Material and Fuel Storage Edge 60 Pellet Fireplace Fire SafetyCombustible/Non-Combustible Materials General Operating Information Power SwitchAuto-Clean Firepot System Before Your First FireIgnition Cycles Edge 60 Pellet Fireplace Filling the Hopper with FuelStarting Your First Fire Manual Mode Auto-Clean CycleAutomatic Mode Soft Start Cycle SS-Low / SS-MedBattery Back-up System Optional Edge 60 Pellet Fireplace Battery Back-up System Cont’d Clear SpaceMaintaining & Servicing Your Appliance Quick Reference Maintenance ChartCleaning or Inspection Before Servicing Your ApplianceAccessing Components for Maintenance Edge 60 Pellet Fireplace High Ash Fuel Content MaintenanceDisposal of Ashes Frequency As needed Auto-Clean System Inspection & CleaningCleaning Ash Pan Cleaning Heat Exchanger, Drop Tube & Exhaust Shop Vac* Example Micro Cleaning KitClinker Cleaning the Glass Cleaning the HopperCleaning Convection Blower Do Not Use Lubrication Cleaning Exhaust Blower Do Not Use LubricationChimney Inspection and Cleaning Troubleshooting for Homeowner Frequently Asked QuestionsPossible Cause Corrective Action Floor Support Getting StartedAppliance Location Inspect Appliance and Components Checklist to Help Determine LocationTools And Supplies Needed DescriptionRecommended Sequence Material is installed. See Item GCrush Hazard Recommended Locations Framing Dimensions & ClearancesOutside Air Kit is Required for All installations Hearth ExtensionSealing at the Penetration of Building Envelope Frame the FireplaceEdge 60 Pellet Fireplace Construct the Chase 27.1Behind the Mounting Frame Edge 60 Pellet Fireplace Finishing MaterialFlush with the Mounting Frame Protrudes Beyond the Mounting FrameOpening Clearances for the Curved Tuscan and Natural Fronts Opening Clearances for the Studio Front Edge 60 Pellet Fireplace Mantel Fuel Loading Clearances Rise to run ratioEdge 60 Pellet Fireplace Non-Combustible Materials Combustible MaterialsSub-Floor Material & Securing Fireplace Crush Hazard Installation of FireplacePosition the Fireplace Power Supply Cord Wall Control Wire Shock HazardVertical Installation Back Side of Wall Control with Cover OffVertical Installation Cont’d Horizontal Installation Do not Terminate Vent Vent InformationVenting Termination Minimum Requirements Termination must exhaust above air inlet elevationEdge 60 Pellet Fireplace Avoiding Smoke and Odors Edge 60 Pellet Fireplace Negative Pressure Draft Example of 3 Elbow-Rear Vent Termination Calculation Edge 60 Pellet Fireplace Chimney and Exhaust ConnectionEquivalent Feet of Pipe Edge 60 Pellet Fireplace Pipe Selection Chart Altitude in Thousands of FeetLeft Rear Corner Right Rear Corner Rear of Fireplace Outside Air Inlet LocationsEdge 60 Pellet Fireplace Outside Air Kit Installation Install Outside Air KitVertical Interior Typical Installation Through the Wall & Vertical ExteriorStraight Out Choose which one is best for your installationEdge 60 Pellet Fireplace Through the Wall DegreeMobile Home Installation Rebox. Figures 47.1 Optional Log Set Placement InstructionsAppliance Set-Up Rebox. Figures 47.3Front Installation Replacement Parts Glass ReplacementConvection Blower Replacement Baffl e Removal & Replacement Troubleshooting For Installers Error MessageTop View Fireplace DimensionsReference Materials Rear ViewEdge 60 Pellet Fireplace Component Functions Vacuum Switch Power SupplyPower Switch Overheat Sensor Snap DiscEdge 60 Pellet Fireplace Component Locations View of Left RearEdge 60 Pellet Fireplace Service And Maintenance Log Date of Service Performed By Description of ServiceContact Information Hearth & Home Technologies

7051-158B specifications

The Quadra-Fire 7051-158B is a premier wood-burning fireplace designed for homeowners seeking an efficient and aesthetically pleasing heating solution. This fireplace combines advanced technology with classic design, making it an exceptional choice for any living space.

One of the key features of the 7051-158B is its impressive heating capability. With a maximum heat output of up to 75,000 BTUs, it can effectively warm areas up to 2,500 square feet. This makes it ideal for both large homes and open-concept areas. The fireplace is equipped with a large firebox that can accommodate logs up to 24 inches, allowing for longer burn times and fewer reloads, thereby enhancing convenience for users.

Efficiency is a major focus of the Quadra-Fire 7051-158B. The unit boasts an impressive EPA-certified efficiency rating, which signifies that it burns wood cleanly and effectively, producing minimal smoke and emissions. This not only benefits the environment but also maximizes the warmth generated from each log of wood burned. The unit is designed to maintain a consistent temperature with its advanced combustion technology, which ensures a clean burn while maximizing heat output.

To enhance user experience, the 7051-158B incorporates several technological features. One such innovation is the Quadra-Fire's patented Four-Point Burn Technology, which promotes optimal airflow and combustion. This technology results in a more complete burn, reducing the amount of creosote buildup in the chimney and enhancing safety. The fireplace also comes with an easy-to-use air control system, allowing homeowners to easily adjust the amount of air entering the firebox for customized heat and burn rates.

From a design perspective, the Quadra-Fire 7051-158B offers a perfect blend of traditional and contemporary aesthetics. The elegant exterior is available in various finishes, enabling homeowners to choose an option that complements their decor. Large glass doors provide a captivating view of the flames, creating a cozy ambiance in any room.

In conclusion, the Quadra-Fire 7051-158B stands out as a top choice for wood-burning fireplaces. With its efficient heating capabilities, cutting-edge technology, and beautiful design, it is sure to enhance both the comfort and appeal of your home. Whether you are looking to heat a large space or simply enjoy the warmth of a wood fire, this fireplace provides a reliable and stylish solution.
Top Page Image Contents