Quadra-Fire 7051-158B Crush Hazard, Recommended Sequence, Material is installed. See Item G

Page 25

R

EDGE 60 Pellet Fireplace

F. Recommended Sequence of Installation

G. Items to Verify During Test Burn

NOTICE:

Read and understand Sections 6 through 10 for detailed information before installing the fi replace.

Follow all clearances as specifi ed.

The choice of fi nishing material and decorative front must be determined before installation can begin as it will determine the placement of the fi replace.

Outside air is required on all installations and the Outside Air Kit must be ordered separately.

Check for leaks in the exhaust venting system. Do you see any smoke?

Remember on a fi rst burn odors and vapors are released due to the curing of the high tem- perature paint. The focus is on the venting system.

Check overall operation, are there any error codes on the Wall Control?

Confi rm that outside air is hooked up and properly sealed. Is there cold air infi ltration?

 

Recommended Sequence

 

 

1.

Identify the exhaust vent and outside air locations

 

and install necessary venting components including

 

wall thimble, fi re stop or roof fl ashing for a verti-

 

cal termination. NOTE: Outside Air Kit must be

 

ordered separately.

 

 

2.

Complete the framing.

 

 

3.

Install the electrical junction box near the electrical

 

opening on the left side of the appliance. Maximum

 

distance of 9 inches (229mm) from appliance.

 

 

4.

Identify the location of the wall control and run the

 

wire (25 ft [7.62 meters] in length) to the left side of

 

the appliance.

 

 

5.

Prepare the fi replace for the exhaust vent adapter.

 

Install adapter, seal with high temp silicone and

 

screws and install all cover plates.

 

 

6.

Preset the nailing fl anges depending on the thick-

 

ness of your fi nishing material.

 

 

7.

Ensure that fi replace is level before securing in

 

place. If not level the decorative front will not swing

 

out properly.

 

 

8.

IT IS CRUCIAL FIREPLACE IS ROBUSTLY

 

SECURED. Slide the fi replace into place and

 

secure to the fl oor with the securing brackets and to

 

the wall. See page 33 for detailed instructions.

 

 

9.

Attach the exhaust and outside air venting to the

 

appliance.

 

 

10.

Hook up power and the wall control.

 

 

11.

Slide the fi replace out on the rail system to validate

 

that it is secure and there is no defl ection in the

 

outer can.

 

 

12.

Slide the fi replace back into the outer can. Re-attach

 

the bolts and brackets. Double check they are cor-

 

rectly positioned to ensure the exhaust gaskets are

 

properly sealed to prevent combustion leakage.

 

 

13.

A burn test must be performed before fi nishing

 

material is installed. (See Item “G”).

 

 

14.

Install the fi nishing material.

 

 

15.

Install the decorative front.

 

 

WARNING

Crush Hazard!

To avoid tipping over, this appliance must be securely fastened to the fl oor.

The fi replace must be secured in place as outlined in Section 6 and 7.

When servicing the fi replace, the fi replace slides foward on the rail system.

Tipping can occur if fi replace is not properly secured to the fl oor.

December 6, 2011

7051-158B

Page 25

Image 25
Contents Hot glass will cause burns Natural Curved Tuscan StudioSerial Number Label Edge 60 Pellet FireplaceTable of Contents Edge 60 Pellet Fireplace Edge 60 Pellet Fireplace Listing and Code Approvals Operating Instructions User’s GuideCombustible/Non-Combustible Materials Edge 60 Pellet Fireplace Fire SafetyFuel Material and Fuel Storage Auto-Clean Firepot System Power SwitchGeneral Operating Information Before Your First FireStarting Your First Fire Edge 60 Pellet Fireplace Filling the Hopper with FuelIgnition Cycles Automatic Mode Auto-Clean CycleManual Mode Soft Start Cycle SS-Low / SS-MedBattery Back-up System Optional Clear Space Edge 60 Pellet Fireplace Battery Back-up System Cont’dCleaning or Inspection Quick Reference Maintenance ChartMaintaining & Servicing Your Appliance Before Servicing Your ApplianceEdge 60 Pellet Fireplace High Ash Fuel Content Maintenance Accessing Components for MaintenanceCleaning Ash Pan Auto-Clean System Inspection & CleaningDisposal of Ashes Frequency As needed Shop Vac* Example Micro Cleaning Kit Cleaning Heat Exchanger, Drop Tube & ExhaustClinker Cleaning Convection Blower Do Not Use Lubrication Cleaning the HopperCleaning the Glass Cleaning Exhaust Blower Do Not Use LubricationChimney Inspection and Cleaning Frequently Asked Questions Troubleshooting for HomeownerPossible Cause Corrective Action Appliance Location Getting StartedFloor Support Tools And Supplies Needed Checklist to Help Determine LocationInspect Appliance and Components DescriptionCrush Hazard Material is installed. See Item GRecommended Sequence Outside Air Kit is Required for All installations Framing Dimensions & ClearancesRecommended Locations Hearth ExtensionFrame the Fireplace Sealing at the Penetration of Building Envelope27.1 Edge 60 Pellet Fireplace Construct the ChaseFlush with the Mounting Frame Edge 60 Pellet Fireplace Finishing MaterialBehind the Mounting Frame Protrudes Beyond the Mounting FrameOpening Clearances for the Curved Tuscan and Natural Fronts Opening Clearances for the Studio Front Rise to run ratio Edge 60 Pellet Fireplace Mantel Fuel Loading ClearancesCombustible Materials Edge 60 Pellet Fireplace Non-Combustible MaterialsPosition the Fireplace Installation of FireplaceSub-Floor Material & Securing Fireplace Crush Hazard Shock Hazard Power Supply Cord Wall Control WireBack Side of Wall Control with Cover Off Vertical InstallationVertical Installation Cont’d Horizontal Installation Venting Termination Minimum Requirements Vent InformationDo not Terminate Vent Termination must exhaust above air inlet elevationEdge 60 Pellet Fireplace Avoiding Smoke and Odors Edge 60 Pellet Fireplace Negative Pressure Draft Equivalent Feet of Pipe Edge 60 Pellet Fireplace Chimney and Exhaust ConnectionExample of 3 Elbow-Rear Vent Termination Calculation Altitude in Thousands of Feet Edge 60 Pellet Fireplace Pipe Selection ChartOutside Air Inlet Locations Left Rear Corner Right Rear Corner Rear of FireplaceInstall Outside Air Kit Edge 60 Pellet Fireplace Outside Air Kit InstallationThrough the Wall & Vertical Exterior Vertical Interior Typical InstallationEdge 60 Pellet Fireplace Through the Wall Choose which one is best for your installationStraight Out DegreeMobile Home Installation Appliance Set-Up Optional Log Set Placement InstructionsRebox. Figures 47.1 Rebox. Figures 47.3Front Installation Glass Replacement Replacement PartsConvection Blower Replacement Baffl e Removal & Replacement Error Message Troubleshooting For InstallersReference Materials Fireplace DimensionsTop View Rear ViewEdge 60 Pellet Fireplace Component Functions Power Switch Power SupplyVacuum Switch Overheat Sensor Snap DiscView of Left Rear Edge 60 Pellet Fireplace Component LocationsDate of Service Performed By Description of Service Edge 60 Pellet Fireplace Service And Maintenance LogHearth & Home Technologies Contact Information

7051-158B specifications

The Quadra-Fire 7051-158B is a premier wood-burning fireplace designed for homeowners seeking an efficient and aesthetically pleasing heating solution. This fireplace combines advanced technology with classic design, making it an exceptional choice for any living space.

One of the key features of the 7051-158B is its impressive heating capability. With a maximum heat output of up to 75,000 BTUs, it can effectively warm areas up to 2,500 square feet. This makes it ideal for both large homes and open-concept areas. The fireplace is equipped with a large firebox that can accommodate logs up to 24 inches, allowing for longer burn times and fewer reloads, thereby enhancing convenience for users.

Efficiency is a major focus of the Quadra-Fire 7051-158B. The unit boasts an impressive EPA-certified efficiency rating, which signifies that it burns wood cleanly and effectively, producing minimal smoke and emissions. This not only benefits the environment but also maximizes the warmth generated from each log of wood burned. The unit is designed to maintain a consistent temperature with its advanced combustion technology, which ensures a clean burn while maximizing heat output.

To enhance user experience, the 7051-158B incorporates several technological features. One such innovation is the Quadra-Fire's patented Four-Point Burn Technology, which promotes optimal airflow and combustion. This technology results in a more complete burn, reducing the amount of creosote buildup in the chimney and enhancing safety. The fireplace also comes with an easy-to-use air control system, allowing homeowners to easily adjust the amount of air entering the firebox for customized heat and burn rates.

From a design perspective, the Quadra-Fire 7051-158B offers a perfect blend of traditional and contemporary aesthetics. The elegant exterior is available in various finishes, enabling homeowners to choose an option that complements their decor. Large glass doors provide a captivating view of the flames, creating a cozy ambiance in any room.

In conclusion, the Quadra-Fire 7051-158B stands out as a top choice for wood-burning fireplaces. With its efficient heating capabilities, cutting-edge technology, and beautiful design, it is sure to enhance both the comfort and appeal of your home. Whether you are looking to heat a large space or simply enjoy the warmth of a wood fire, this fireplace provides a reliable and stylish solution.