Quadra-Fire 7051-158B owner manual Edge 60 Pellet Fireplace

Page 37

R

EDGE 60 Pellet Fireplace

Vertical Installation (Cont’d)

Horizontal Installation

Pipe

Flue Collar

Liberally silicone all around flue collar before inserting into pipe

Top Cover Plate

Figure 36.1

Drill Holes for Screws above Locating Pins

X

1.Remove the fl ue collar and orange gasket from the component pack. Push out the 6 slugs in the gasket.

2.Remove the rear cover plate. Save screws and plate for later re-attachment.

3.Place the orange fl ue gasket over the locating pins on the exhaust fl ue transition on the back of the fi replace. Figure 35.2 on page 35.

4.Position the fl ue collar over the gasket and secure in place.

Figure 36.5.

5.Position the rear cover plate,secure in place. Figure 36.6.

6.Before placing the pipe over the fl ue collar, liberally silicone the end of the fl ue collar with Hi-Temp silicone about 1-1/2 inches (38mm) wide.

7.Drill holes through the pipe walls directly into the fl ue collar one on each side, 180 degrees apart. Screw the pipe to the fl ue collar with 2 screws. Figure 36.7.

Locating Pin on Each Side

Figure 36.2

Insert assemblied pipe and flue collar through top of outer can and over gasket.

Locating Pins each Side

Flue Collar in Horizontal Position

Figure 36.5

REAR COVER PLATE

INSTALLED WITH HOLE

AT THE BOTTOM

Figure 36.6

Secure in place with 4 screws

Figure 36.3

Secure top cover plate in

place.

Attach rear cover plate with hole at the top and secure in place.

Liberally silicone flue collar before placing pipe over collar.

Secure pipe to flue collar with 2 screws, 180 degrees apart

Figure 36.7

Figure 36.4

December 6, 2011

7051-158B

Page 37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Hot glass will cause burns Natural Curved Tuscan StudioSerial Number Label Edge 60 Pellet FireplaceTable of Contents Edge 60 Pellet Fireplace Edge 60 Pellet Fireplace Listing and Code Approvals Operating Instructions User’s GuideCombustible/Non-Combustible Materials Edge 60 Pellet Fireplace Fire SafetyFuel Material and Fuel Storage Auto-Clean Firepot System Power SwitchGeneral Operating Information Before Your First FireStarting Your First Fire Edge 60 Pellet Fireplace Filling the Hopper with FuelIgnition Cycles Automatic Mode Auto-Clean CycleManual Mode Soft Start Cycle SS-Low / SS-MedBattery Back-up System Optional Clear Space Edge 60 Pellet Fireplace Battery Back-up System Cont’dCleaning or Inspection Quick Reference Maintenance ChartMaintaining & Servicing Your Appliance Before Servicing Your ApplianceEdge 60 Pellet Fireplace High Ash Fuel Content Maintenance Accessing Components for MaintenanceCleaning Ash Pan Auto-Clean System Inspection & CleaningDisposal of Ashes Frequency As needed Shop Vac* Example Micro Cleaning Kit Cleaning Heat Exchanger, Drop Tube & ExhaustClinker Cleaning Convection Blower Do Not Use Lubrication Cleaning the HopperCleaning the Glass Cleaning Exhaust Blower Do Not Use LubricationChimney Inspection and Cleaning Frequently Asked Questions Troubleshooting for HomeownerPossible Cause Corrective Action Appliance Location Getting StartedFloor Support Tools And Supplies Needed Checklist to Help Determine LocationInspect Appliance and Components DescriptionCrush Hazard Material is installed. See Item GRecommended Sequence Outside Air Kit is Required for All installations Framing Dimensions & ClearancesRecommended Locations Hearth ExtensionFrame the Fireplace Sealing at the Penetration of Building Envelope27.1 Edge 60 Pellet Fireplace Construct the ChaseFlush with the Mounting Frame Edge 60 Pellet Fireplace Finishing MaterialBehind the Mounting Frame Protrudes Beyond the Mounting FrameOpening Clearances for the Curved Tuscan and Natural Fronts Opening Clearances for the Studio Front Rise to run ratio Edge 60 Pellet Fireplace Mantel Fuel Loading ClearancesCombustible Materials Edge 60 Pellet Fireplace Non-Combustible MaterialsPosition the Fireplace Installation of FireplaceSub-Floor Material & Securing Fireplace Crush Hazard Shock Hazard Power Supply Cord Wall Control WireBack Side of Wall Control with Cover Off Vertical InstallationVertical Installation Cont’d Horizontal Installation Venting Termination Minimum Requirements Vent InformationDo not Terminate Vent Termination must exhaust above air inlet elevationEdge 60 Pellet Fireplace Avoiding Smoke and Odors Edge 60 Pellet Fireplace Negative Pressure Draft Equivalent Feet of Pipe Edge 60 Pellet Fireplace Chimney and Exhaust ConnectionExample of 3 Elbow-Rear Vent Termination Calculation Altitude in Thousands of Feet Edge 60 Pellet Fireplace Pipe Selection ChartOutside Air Inlet Locations Left Rear Corner Right Rear Corner Rear of FireplaceInstall Outside Air Kit Edge 60 Pellet Fireplace Outside Air Kit InstallationThrough the Wall & Vertical Exterior Vertical Interior Typical InstallationEdge 60 Pellet Fireplace Through the Wall Choose which one is best for your installationStraight Out DegreeMobile Home Installation Appliance Set-Up Optional Log Set Placement InstructionsRebox. Figures 47.1 Rebox. Figures 47.3Front Installation Glass Replacement Replacement PartsConvection Blower Replacement Baffl e Removal & Replacement Error Message Troubleshooting For InstallersReference Materials Fireplace DimensionsTop View Rear ViewEdge 60 Pellet Fireplace Component Functions Power Switch Power SupplyVacuum Switch Overheat Sensor Snap DiscView of Left Rear Edge 60 Pellet Fireplace Component LocationsDate of Service Performed By Description of Service Edge 60 Pellet Fireplace Service And Maintenance LogHearth & Home Technologies Contact Information

7051-158B specifications

The Quadra-Fire 7051-158B is a premier wood-burning fireplace designed for homeowners seeking an efficient and aesthetically pleasing heating solution. This fireplace combines advanced technology with classic design, making it an exceptional choice for any living space.

One of the key features of the 7051-158B is its impressive heating capability. With a maximum heat output of up to 75,000 BTUs, it can effectively warm areas up to 2,500 square feet. This makes it ideal for both large homes and open-concept areas. The fireplace is equipped with a large firebox that can accommodate logs up to 24 inches, allowing for longer burn times and fewer reloads, thereby enhancing convenience for users.

Efficiency is a major focus of the Quadra-Fire 7051-158B. The unit boasts an impressive EPA-certified efficiency rating, which signifies that it burns wood cleanly and effectively, producing minimal smoke and emissions. This not only benefits the environment but also maximizes the warmth generated from each log of wood burned. The unit is designed to maintain a consistent temperature with its advanced combustion technology, which ensures a clean burn while maximizing heat output.

To enhance user experience, the 7051-158B incorporates several technological features. One such innovation is the Quadra-Fire's patented Four-Point Burn Technology, which promotes optimal airflow and combustion. This technology results in a more complete burn, reducing the amount of creosote buildup in the chimney and enhancing safety. The fireplace also comes with an easy-to-use air control system, allowing homeowners to easily adjust the amount of air entering the firebox for customized heat and burn rates.

From a design perspective, the Quadra-Fire 7051-158B offers a perfect blend of traditional and contemporary aesthetics. The elegant exterior is available in various finishes, enabling homeowners to choose an option that complements their decor. Large glass doors provide a captivating view of the flames, creating a cozy ambiance in any room.

In conclusion, the Quadra-Fire 7051-158B stands out as a top choice for wood-burning fireplaces. With its efficient heating capabilities, cutting-edge technology, and beautiful design, it is sure to enhance both the comfort and appeal of your home. Whether you are looking to heat a large space or simply enjoy the warmth of a wood fire, this fireplace provides a reliable and stylish solution.
Top Page Image Contents