Quadra-Fire 7051-158B General Operating Information, Power Switch, Before Your First Fire, = on

Page 9

R

EDGE 60 Pellet Fireplace

CAUTION! Tested and approved for wood pellets, shelled

field corn, wheat and black oil sunfl ower seeds. Burning of any other type of fuel voids your warranty.

Changing to Different Fuel Type

•Empty the hopper of the previous fuel

•Thoroughly vacuum hopper before fi lling with the new fuel

•Select the appropriate setting on the FUEL SELECTION screen on the thermostat wall control

The burn rate, BTU content and heat output will all vary depending on the fuel selected.

Storage

•Wood pellets should be left in their original sealed bag until using to prevent moisture absorption.

•Shelled corn, wheat or sunfl ower seeds should be stored in a tight container to prevent it from absorbing moisture from damp or wet fl oors.

•This will also prevent rodents from becoming a problem.

•Do not store any pellet fuel within the clearance requirements or in an area that would hinder routine cleaning and maintenance.

D. General Operating Information

Read and understand the Thermostat Wall Control manual for detailed operating instructions. The wall control is an intregal part of how to operate this appliance.

1. Thermostat Wall Control - Automatic Setting

2. Thermostat Wall Control - Manual Setting

When you select “Manual” on the AUTO/MANUAL screen the appliance will still automatically turn on and off according to the temperature setting.

However, you will be able to manually control the heat output levels. Adjust the heat output levels by using the HEAT OUTPUT LEVEL screen. Figure 9.2.

Medium

Figure 9.2

3. Auto-Clean Firepot System

Your appliance is equipped with an automatic fi repot cleaning system that will change the frequency of cleaning based on the fuel being burned.

The auto-clean system will clean itself immediately on initial plug in. If there is a power outage, as soon as power is restored it will recycle and clean itself if there is no fi re in the fi repot.

NOTE: User is responsible for removing the ash from the ash drawer.

E. Power Switch

The power switch is located at the bottom right hand corner of the fi replace. It turns the power on and off to the fi replace.

Before servicing the fi replace this power switch must be in the off position. When the power switch is OFF there will be no display on the wall control screen.

The appliance is like most modern furnaces; when the thermostat wall control calls for heat, your appliance will automatically light and deliver heat.

When the room is up to temperature and the wall control is satisfi ed the appliance will shut down.

In the automatic setting the heat output level is controlled by the wall control. Select “Automatic” on the AUTO/MANUAL screen. Figure 9.1.

POWER SWITCH

Figure 9.3

Power Switch

I

0

=ON

=OFF

Automatic

Manual

Off

Figure 9.1

F. Before Your First Fire

•First, make sure your appliance has been properly installed and that all safety requirements have been met.

•Pay particular attention to the fi re protection, venting and thermostat wall control installation instructions.

•Double check that the ash pan, hopper and fi rebox are empty and then close the fi rebox door.

NOTICE: The tip of thermocouple must be in contact with the inside end of the thermocouple cover or missed ignitions can occur.

December 6, 2011

7051-158B

Page 9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Hot glass will cause burns Natural Curved Tuscan StudioSerial Number Label Edge 60 Pellet FireplaceTable of Contents Edge 60 Pellet Fireplace Edge 60 Pellet Fireplace Listing and Code Approvals Operating Instructions User’s GuideEdge 60 Pellet Fireplace Fire Safety Combustible/Non-Combustible MaterialsFuel Material and Fuel Storage Auto-Clean Firepot System Power SwitchGeneral Operating Information Before Your First FireEdge 60 Pellet Fireplace Filling the Hopper with Fuel Starting Your First FireIgnition Cycles Automatic Mode Auto-Clean CycleManual Mode Soft Start Cycle SS-Low / SS-MedBattery Back-up System Optional Clear Space Edge 60 Pellet Fireplace Battery Back-up System Cont’dCleaning or Inspection Quick Reference Maintenance ChartMaintaining & Servicing Your Appliance Before Servicing Your ApplianceEdge 60 Pellet Fireplace High Ash Fuel Content Maintenance Accessing Components for MaintenanceAuto-Clean System Inspection & Cleaning Cleaning Ash PanDisposal of Ashes Frequency As needed Shop Vac* Example Micro Cleaning Kit Cleaning Heat Exchanger, Drop Tube & ExhaustClinker Cleaning Convection Blower Do Not Use Lubrication Cleaning the HopperCleaning the Glass Cleaning Exhaust Blower Do Not Use LubricationChimney Inspection and Cleaning Frequently Asked Questions Troubleshooting for HomeownerPossible Cause Corrective Action Getting Started Appliance LocationFloor Support Tools And Supplies Needed Checklist to Help Determine LocationInspect Appliance and Components DescriptionMaterial is installed. See Item G Crush HazardRecommended Sequence Outside Air Kit is Required for All installations Framing Dimensions & ClearancesRecommended Locations Hearth ExtensionFrame the Fireplace Sealing at the Penetration of Building Envelope27.1 Edge 60 Pellet Fireplace Construct the ChaseFlush with the Mounting Frame Edge 60 Pellet Fireplace Finishing MaterialBehind the Mounting Frame Protrudes Beyond the Mounting FrameOpening Clearances for the Curved Tuscan and Natural Fronts Opening Clearances for the Studio Front Rise to run ratio Edge 60 Pellet Fireplace Mantel Fuel Loading ClearancesCombustible Materials Edge 60 Pellet Fireplace Non-Combustible MaterialsInstallation of Fireplace Position the FireplaceSub-Floor Material & Securing Fireplace Crush Hazard Shock Hazard Power Supply Cord Wall Control WireBack Side of Wall Control with Cover Off Vertical InstallationVertical Installation Cont’d Horizontal Installation Venting Termination Minimum Requirements Vent InformationDo not Terminate Vent Termination must exhaust above air inlet elevationEdge 60 Pellet Fireplace Avoiding Smoke and Odors Edge 60 Pellet Fireplace Negative Pressure Draft Edge 60 Pellet Fireplace Chimney and Exhaust Connection Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculation Altitude in Thousands of Feet Edge 60 Pellet Fireplace Pipe Selection ChartOutside Air Inlet Locations Left Rear Corner Right Rear Corner Rear of FireplaceInstall Outside Air Kit Edge 60 Pellet Fireplace Outside Air Kit InstallationThrough the Wall & Vertical Exterior Vertical Interior Typical InstallationEdge 60 Pellet Fireplace Through the Wall Choose which one is best for your installationStraight Out DegreeMobile Home Installation Appliance Set-Up Optional Log Set Placement InstructionsRebox. Figures 47.1 Rebox. Figures 47.3Front Installation Glass Replacement Replacement PartsConvection Blower Replacement Baffl e Removal & Replacement Error Message Troubleshooting For InstallersReference Materials Fireplace DimensionsTop View Rear ViewEdge 60 Pellet Fireplace Component Functions Power Switch Power SupplyVacuum Switch Overheat Sensor Snap DiscView of Left Rear Edge 60 Pellet Fireplace Component LocationsDate of Service Performed By Description of Service Edge 60 Pellet Fireplace Service And Maintenance LogHearth & Home Technologies Contact Information

7051-158B specifications

The Quadra-Fire 7051-158B is a premier wood-burning fireplace designed for homeowners seeking an efficient and aesthetically pleasing heating solution. This fireplace combines advanced technology with classic design, making it an exceptional choice for any living space.

One of the key features of the 7051-158B is its impressive heating capability. With a maximum heat output of up to 75,000 BTUs, it can effectively warm areas up to 2,500 square feet. This makes it ideal for both large homes and open-concept areas. The fireplace is equipped with a large firebox that can accommodate logs up to 24 inches, allowing for longer burn times and fewer reloads, thereby enhancing convenience for users.

Efficiency is a major focus of the Quadra-Fire 7051-158B. The unit boasts an impressive EPA-certified efficiency rating, which signifies that it burns wood cleanly and effectively, producing minimal smoke and emissions. This not only benefits the environment but also maximizes the warmth generated from each log of wood burned. The unit is designed to maintain a consistent temperature with its advanced combustion technology, which ensures a clean burn while maximizing heat output.

To enhance user experience, the 7051-158B incorporates several technological features. One such innovation is the Quadra-Fire's patented Four-Point Burn Technology, which promotes optimal airflow and combustion. This technology results in a more complete burn, reducing the amount of creosote buildup in the chimney and enhancing safety. The fireplace also comes with an easy-to-use air control system, allowing homeowners to easily adjust the amount of air entering the firebox for customized heat and burn rates.

From a design perspective, the Quadra-Fire 7051-158B offers a perfect blend of traditional and contemporary aesthetics. The elegant exterior is available in various finishes, enabling homeowners to choose an option that complements their decor. Large glass doors provide a captivating view of the flames, creating a cozy ambiance in any room.

In conclusion, the Quadra-Fire 7051-158B stands out as a top choice for wood-burning fireplaces. With its efficient heating capabilities, cutting-edge technology, and beautiful design, it is sure to enhance both the comfort and appeal of your home. Whether you are looking to heat a large space or simply enjoy the warmth of a wood fire, this fireplace provides a reliable and stylish solution.
Top Page Image Contents