Quadra-Fire 7051-158B owner manual Convection Blower Replacement Baffl e Removal & Replacement

Page 51

R

EDGE 60 Pellet Fireplace

C. Convection Blower Replacement

D. Baffl e Removal & Replacement

1.Follow the proper shut down procedures as outlined on page 14, Section 3.A.

2.Remove the 2 bolts from the bottom left and right side of the fi replace and slide the fi replace out.

3.Locate the convection blower on the bottom left rear of the fi replace. Reach behind the blower and release the latch by pushing the top of the latch towards the blower. Figure 50.1.

4.Rock the top of the blower slightly and lift up and out. The blower will pass around the control board and out the side of the fi replace.

5.Disconnect the wire harness from the bottom of the blower by depressing the tabs on the sides of the con- nector and then pulling to remove.

6.Re-connect wire harness to the new replacement blower. Install the blower by placing the bottom fl ange into the opening fi rst then rotate blower up into posi- tion.

7.When the blower is properly positioned the latch will engage the notch to hold the blower in place. Figure 50.2.

8.Slide appliance back in position and re-install bolts.

RELEASE THE LATCH

Figure 50.1

Figure 50.2

WARNING! Risk of Injury! Cast iron is a very heavy material. The baffl e is made of cast iron and therefore is heavy and awkward at times to maneuver. Clear and prepare your work area before you begin.

1.Follow the proper shut down procedures as outlined on page 14, Section 3.A.

2.Open front and open fi rebox door.

3.The baffl e is located at the top inside of fi rebox.

4.To remove the baffl e:

a.Place a fl at head screwdriver into the slot of the latches located in the upper corners. Figure 50.3.

b.Push down and the bottom of the latch will fall forward off of the post.

c.Lift the baffl e up and then out toward you.

5.To replace the baffl e:

a.Place the 2 locating ears behind the bottom edge.

b.Tilt the baffl e up and into place.

The baffl e must be centered in the fi rebox before latching it in place.

c.If it is not centered the latch is trapped between the baffl e and side of the fi rebox instead of latch- ing properly.

d.The bottom of the latches will fi t over the posts.

e.Push the top of the latch forward to lock latch into place.

Baffle

Latches

Locating ears - 1 on

Insert flat head screw driver into “V”

each side. Fit behind

bottom edge.

section and push down and the bottom

 

of the latch will fall forward off of post

 

Figure 50.3

December 6, 2011

7051-158B

Page 51

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Hot glass will cause burns Natural Curved Tuscan StudioSerial Number Label Edge 60 Pellet FireplaceTable of Contents Edge 60 Pellet Fireplace Edge 60 Pellet Fireplace Listing and Code Approvals Operating Instructions User’s GuideEdge 60 Pellet Fireplace Fire Safety Combustible/Non-Combustible MaterialsFuel Material and Fuel Storage Before Your First Fire Power SwitchAuto-Clean Firepot System General Operating InformationEdge 60 Pellet Fireplace Filling the Hopper with Fuel Starting Your First FireIgnition Cycles Soft Start Cycle SS-Low / SS-Med Auto-Clean CycleAutomatic Mode Manual ModeBattery Back-up System Optional Clear Space Edge 60 Pellet Fireplace Battery Back-up System Cont’dBefore Servicing Your Appliance Quick Reference Maintenance ChartCleaning or Inspection Maintaining & Servicing Your ApplianceEdge 60 Pellet Fireplace High Ash Fuel Content Maintenance Accessing Components for MaintenanceAuto-Clean System Inspection & Cleaning Cleaning Ash PanDisposal of Ashes Frequency As needed Shop Vac* Example Micro Cleaning Kit Cleaning Heat Exchanger, Drop Tube & ExhaustClinker Cleaning Exhaust Blower Do Not Use Lubrication Cleaning the HopperCleaning Convection Blower Do Not Use Lubrication Cleaning the GlassChimney Inspection and Cleaning Frequently Asked Questions Troubleshooting for HomeownerPossible Cause Corrective Action Getting Started Appliance LocationFloor Support Description Checklist to Help Determine LocationTools And Supplies Needed Inspect Appliance and ComponentsMaterial is installed. See Item G Crush HazardRecommended Sequence Hearth Extension Framing Dimensions & ClearancesOutside Air Kit is Required for All installations Recommended LocationsFrame the Fireplace Sealing at the Penetration of Building Envelope27.1 Edge 60 Pellet Fireplace Construct the ChaseProtrudes Beyond the Mounting Frame Edge 60 Pellet Fireplace Finishing MaterialFlush with the Mounting Frame Behind the Mounting FrameOpening Clearances for the Curved Tuscan and Natural Fronts Opening Clearances for the Studio Front Rise to run ratio Edge 60 Pellet Fireplace Mantel Fuel Loading ClearancesCombustible Materials Edge 60 Pellet Fireplace Non-Combustible MaterialsInstallation of Fireplace Position the FireplaceSub-Floor Material & Securing Fireplace Crush Hazard Shock Hazard Power Supply Cord Wall Control WireBack Side of Wall Control with Cover Off Vertical InstallationVertical Installation Cont’d Horizontal Installation Termination must exhaust above air inlet elevation Vent InformationVenting Termination Minimum Requirements Do not Terminate VentEdge 60 Pellet Fireplace Avoiding Smoke and Odors Edge 60 Pellet Fireplace Negative Pressure Draft Edge 60 Pellet Fireplace Chimney and Exhaust Connection Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculation Altitude in Thousands of Feet Edge 60 Pellet Fireplace Pipe Selection ChartOutside Air Inlet Locations Left Rear Corner Right Rear Corner Rear of FireplaceInstall Outside Air Kit Edge 60 Pellet Fireplace Outside Air Kit InstallationThrough the Wall & Vertical Exterior Vertical Interior Typical InstallationDegree Choose which one is best for your installationEdge 60 Pellet Fireplace Through the Wall Straight OutMobile Home Installation Rebox. Figures 47.3 Optional Log Set Placement InstructionsAppliance Set-Up Rebox. Figures 47.1Front Installation Glass Replacement Replacement PartsConvection Blower Replacement Baffl e Removal & Replacement Error Message Troubleshooting For InstallersRear View Fireplace DimensionsReference Materials Top ViewEdge 60 Pellet Fireplace Component Functions Overheat Sensor Snap Disc Power SupplyPower Switch Vacuum SwitchView of Left Rear Edge 60 Pellet Fireplace Component LocationsDate of Service Performed By Description of Service Edge 60 Pellet Fireplace Service And Maintenance LogHearth & Home Technologies Contact Information

7051-158B specifications

The Quadra-Fire 7051-158B is a premier wood-burning fireplace designed for homeowners seeking an efficient and aesthetically pleasing heating solution. This fireplace combines advanced technology with classic design, making it an exceptional choice for any living space.

One of the key features of the 7051-158B is its impressive heating capability. With a maximum heat output of up to 75,000 BTUs, it can effectively warm areas up to 2,500 square feet. This makes it ideal for both large homes and open-concept areas. The fireplace is equipped with a large firebox that can accommodate logs up to 24 inches, allowing for longer burn times and fewer reloads, thereby enhancing convenience for users.

Efficiency is a major focus of the Quadra-Fire 7051-158B. The unit boasts an impressive EPA-certified efficiency rating, which signifies that it burns wood cleanly and effectively, producing minimal smoke and emissions. This not only benefits the environment but also maximizes the warmth generated from each log of wood burned. The unit is designed to maintain a consistent temperature with its advanced combustion technology, which ensures a clean burn while maximizing heat output.

To enhance user experience, the 7051-158B incorporates several technological features. One such innovation is the Quadra-Fire's patented Four-Point Burn Technology, which promotes optimal airflow and combustion. This technology results in a more complete burn, reducing the amount of creosote buildup in the chimney and enhancing safety. The fireplace also comes with an easy-to-use air control system, allowing homeowners to easily adjust the amount of air entering the firebox for customized heat and burn rates.

From a design perspective, the Quadra-Fire 7051-158B offers a perfect blend of traditional and contemporary aesthetics. The elegant exterior is available in various finishes, enabling homeowners to choose an option that complements their decor. Large glass doors provide a captivating view of the flames, creating a cozy ambiance in any room.

In conclusion, the Quadra-Fire 7051-158B stands out as a top choice for wood-burning fireplaces. With its efficient heating capabilities, cutting-edge technology, and beautiful design, it is sure to enhance both the comfort and appeal of your home. Whether you are looking to heat a large space or simply enjoy the warmth of a wood fire, this fireplace provides a reliable and stylish solution.
Top Page Image Contents