Quadra-Fire 7051-158B Edge 60 Pellet Fireplace Finishing Material, Flush with the Mounting Frame

Page 29

R

EDGE 60 Pellet Fireplace

F. Finishing Material

2.Flush with the Mounting Frame

NOTICE: Non-combustible material is not needed to fi nish this appliance.

It is important that the fi nishing material is determined before the appliance is secured to the fl oor. Depending on the fi n- ishing material and installation method, the appliance may need to be positioned further in or out of the wall.

There are three ways fi nishing material can be applied:.

1.Behind the mounting frame

2.Flush with the mounting frame

3.Protrudes beyond the mounting frame

1.Behind the Mounting Frame

The mounting frame is designed to have a 1/2 inch (13mm) overlap on the sides and the top of the framing opening.

Figure 28.1.

Finishing Material Behind

the Mounting Frame

Mounting Frame

Figure 28.1.

Positioning the nailing fl anges:

Slide the nailing fl anges all the way to the front and this will set the appliance for 1/2 inch (13mm) sheet rock.

If tile, marble or other fl at surface fi nish material is desi- ered and you want the mounting frame to cover the cut edge, set the nailing fl anges at a dimension of the sheet rock thickness plus the fi nishing material thickness.

Figure 28.2.

Example: Sheetrock = 1/2 inch (13mm)

Finish Material = 3/8 inch (9.5mm)

Move fl ange: 7/8 inch (22.5mm)

Front of Fireplace

 

Adjustment Screw

7/8 in

 

 

(22.5mm)

Adjustable Nailing Flange

 

Figure 28.2

The fi nish material can not be thicker than 1-1/2 inches (38mm) to use this method. Figure 28.3.

Set the nailing fl anges for sheet rock thickness and install the appliance.

Install the mounting frame.

Install the fi nishing material to edge of the mounting frame.

Finishing Material Flush with Mounting Frame

Mounting Frame

Figure 28.3.

3.Protrudes Beyond the Mounting Frame

This method is mainly used for a brick or stone installa- tion. When fi nishing material is protrudes of the mounting frame and front, there must be a 1-1/4 inch (32mm) airfl ow clearance in front of the mounting frame. Figure 28.4.

Finishing Material Beyond Door Frame

Masonry Spacer

Door Frame

Maintain 1-1/4 inch (32mm) air clearance in front of door frame

Figure 28.4.

Use the masonry spacer supplied with the Front to position the fi nishing material at the proper dimension. Remember to keep the Front opening clearances in mind when fi nishing material is protrudes of the Front. (See pages 29-30) .

Set the nailing fl anges for sheet rock thickness and install the appliance.

Install the mounting frame.

Install the fi nishing material to edge of the mounting frame.

Complete the installation following all specifi ed clear- ances to combustibles.

December 6, 2011

7051-158B

Page 29

Image 29
Contents Hot glass will cause burns Natural Curved Tuscan StudioSerial Number Label Edge 60 Pellet FireplaceTable of Contents Edge 60 Pellet Fireplace Edge 60 Pellet Fireplace Listing and Code Approvals Operating Instructions User’s GuideFuel Material and Fuel Storage Edge 60 Pellet Fireplace Fire SafetyCombustible/Non-Combustible Materials Auto-Clean Firepot System Power SwitchGeneral Operating Information Before Your First FireIgnition Cycles Edge 60 Pellet Fireplace Filling the Hopper with FuelStarting Your First Fire Automatic Mode Auto-Clean CycleManual Mode Soft Start Cycle SS-Low / SS-MedBattery Back-up System Optional Clear Space Edge 60 Pellet Fireplace Battery Back-up System Cont’dCleaning or Inspection Quick Reference Maintenance ChartMaintaining & Servicing Your Appliance Before Servicing Your ApplianceEdge 60 Pellet Fireplace High Ash Fuel Content Maintenance Accessing Components for MaintenanceDisposal of Ashes Frequency As needed Auto-Clean System Inspection & CleaningCleaning Ash Pan Shop Vac* Example Micro Cleaning Kit Cleaning Heat Exchanger, Drop Tube & ExhaustClinker Cleaning Convection Blower Do Not Use Lubrication Cleaning the HopperCleaning the Glass Cleaning Exhaust Blower Do Not Use LubricationChimney Inspection and Cleaning Frequently Asked Questions Troubleshooting for HomeownerPossible Cause Corrective Action Floor Support Getting StartedAppliance Location Tools And Supplies Needed Checklist to Help Determine LocationInspect Appliance and Components DescriptionRecommended Sequence Material is installed. See Item GCrush Hazard Outside Air Kit is Required for All installations Framing Dimensions & ClearancesRecommended Locations Hearth ExtensionFrame the Fireplace Sealing at the Penetration of Building Envelope27.1 Edge 60 Pellet Fireplace Construct the ChaseFlush with the Mounting Frame Edge 60 Pellet Fireplace Finishing MaterialBehind the Mounting Frame Protrudes Beyond the Mounting FrameOpening Clearances for the Curved Tuscan and Natural Fronts Opening Clearances for the Studio Front Rise to run ratio Edge 60 Pellet Fireplace Mantel Fuel Loading ClearancesCombustible Materials Edge 60 Pellet Fireplace Non-Combustible MaterialsSub-Floor Material & Securing Fireplace Crush Hazard Installation of FireplacePosition the Fireplace Shock Hazard Power Supply Cord Wall Control WireBack Side of Wall Control with Cover Off Vertical InstallationVertical Installation Cont’d Horizontal Installation Venting Termination Minimum Requirements Vent InformationDo not Terminate Vent Termination must exhaust above air inlet elevationEdge 60 Pellet Fireplace Avoiding Smoke and Odors Edge 60 Pellet Fireplace Negative Pressure Draft Example of 3 Elbow-Rear Vent Termination Calculation Edge 60 Pellet Fireplace Chimney and Exhaust ConnectionEquivalent Feet of Pipe Altitude in Thousands of Feet Edge 60 Pellet Fireplace Pipe Selection ChartOutside Air Inlet Locations Left Rear Corner Right Rear Corner Rear of FireplaceInstall Outside Air Kit Edge 60 Pellet Fireplace Outside Air Kit InstallationThrough the Wall & Vertical Exterior Vertical Interior Typical InstallationEdge 60 Pellet Fireplace Through the Wall Choose which one is best for your installationStraight Out DegreeMobile Home Installation Appliance Set-Up Optional Log Set Placement InstructionsRebox. Figures 47.1 Rebox. Figures 47.3Front Installation Glass Replacement Replacement PartsConvection Blower Replacement Baffl e Removal & Replacement Error Message Troubleshooting For InstallersReference Materials Fireplace DimensionsTop View Rear ViewEdge 60 Pellet Fireplace Component Functions Power Switch Power SupplyVacuum Switch Overheat Sensor Snap DiscView of Left Rear Edge 60 Pellet Fireplace Component LocationsDate of Service Performed By Description of Service Edge 60 Pellet Fireplace Service And Maintenance LogHearth & Home Technologies Contact Information

7051-158B specifications

The Quadra-Fire 7051-158B is a premier wood-burning fireplace designed for homeowners seeking an efficient and aesthetically pleasing heating solution. This fireplace combines advanced technology with classic design, making it an exceptional choice for any living space.

One of the key features of the 7051-158B is its impressive heating capability. With a maximum heat output of up to 75,000 BTUs, it can effectively warm areas up to 2,500 square feet. This makes it ideal for both large homes and open-concept areas. The fireplace is equipped with a large firebox that can accommodate logs up to 24 inches, allowing for longer burn times and fewer reloads, thereby enhancing convenience for users.

Efficiency is a major focus of the Quadra-Fire 7051-158B. The unit boasts an impressive EPA-certified efficiency rating, which signifies that it burns wood cleanly and effectively, producing minimal smoke and emissions. This not only benefits the environment but also maximizes the warmth generated from each log of wood burned. The unit is designed to maintain a consistent temperature with its advanced combustion technology, which ensures a clean burn while maximizing heat output.

To enhance user experience, the 7051-158B incorporates several technological features. One such innovation is the Quadra-Fire's patented Four-Point Burn Technology, which promotes optimal airflow and combustion. This technology results in a more complete burn, reducing the amount of creosote buildup in the chimney and enhancing safety. The fireplace also comes with an easy-to-use air control system, allowing homeowners to easily adjust the amount of air entering the firebox for customized heat and burn rates.

From a design perspective, the Quadra-Fire 7051-158B offers a perfect blend of traditional and contemporary aesthetics. The elegant exterior is available in various finishes, enabling homeowners to choose an option that complements their decor. Large glass doors provide a captivating view of the flames, creating a cozy ambiance in any room.

In conclusion, the Quadra-Fire 7051-158B stands out as a top choice for wood-burning fireplaces. With its efficient heating capabilities, cutting-edge technology, and beautiful design, it is sure to enhance both the comfort and appeal of your home. Whether you are looking to heat a large space or simply enjoy the warmth of a wood fire, this fireplace provides a reliable and stylish solution.