Vermont Casting 1945 installation instructions Maintenance

Page 28

Defiant Woodburning Stove

Maintenance

Keep Your Stove Looking New

and Working Its Best

Let the fire in the stove go out and allow the stove to cool completely before beginning any maintenance procedure.

Care of the Cast Iron Surface

An occasional dusting with a dry rag will keep the painted cast iron of your Defiant looking new.

The stove’s paint can be touched up as needed. First, mask the areas, such as enamelled parts, glass, or handles, around the spot to be painted. Clean the spot with a wire brush. Remove the griddle and set it aside. It is normal for the griddle to darken after use. You can clean it with a fine-bristle wire brush, or steel wool.

Then, touch up the stove with Vermont Castings’ high temperature stove paint. Apply the paint sparingly; two light coats of paint are better than a single heavy one.

Care of the Porcelain Enamel Surface

Use a dry or slightly damp rag or soft brush to remove spills or stains. For difficult jobs that require a cleaning agent, use only a kitchen appliance cleaner or polish recommended for use on enamel surfaces.

Cleaning the Glass

Most of the carbon deposits on the glass will burn off during hot fires.

However, the ash residue that accumulates on the glass surface should be removed regularly to prevent etching. To clean the glass, follow this procedure:

•Be sure the glass is completely cool.

•Clean the glass with water or a cleaner made espe- cially for this purpose. Do not use abrasive cleaners. Use cleaning agents sparingly and be sure to keep them off the outer surfaces of the stove.

•Rinse the glass thoroughly.

•Dry the glass completely.

Replace Broken Glass Immediately

Do not operate your stove if the glass in the doors is damaged.

If you need to replace the glass, use only the high temperature ceramic glass supplied by Vermont Cast- ings. Do not use substitutes. Be sure to specify left or right glass; the panels are not interchangeable, due to a heat-reflective coating on the side toward the room.

28

Removing the Glass

1.Remove the right and left door assemblies by rais- ing the door until the lower hinge pin clears its hole; then, angle the door bottom slightly outward and pull down to release the upper hinge pin. Place the doors face down on a padded work surface. Be especially careful with enamelled doors.

2.Remove the screws that hold the glass retainer clips in place, and remove the clips.

3.Carefully lift the broken glass panel from the door.

Installing the Glass

Check the gasket around the window; it should be soft and resilient so that the glass will seal properly against the door. Replace the gasket if it has hardened or if it is compressed.

1.Center the glass on the gasket. Be sure to place the glass so that the infrared reflective coating is on the exterior side, facing toward the room.

2.Secure the glass on both doors with the retainer clips. Tighten all screws. (Fig. 38)

3.Replace the doors on the stove.

4.Open and close the doors to check that they fit and work properly. Adjust as necessary.

Door Gasket

Right Door

 

Left Door

 

Glass Gasket

 

Glass Panel

 

Retainer Clip

 

Retainer Clip

 

 

ST547

Fig. 38 An exploded view of the glass assembly.

 

30001693

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Defiant Welcome Save These Instructions for Future ReferenceInstallation Accessories Table of ContentsStory of the Defiant Specifications Defiant, ModelOutside Air InstallationChimney Height What Kind of Chimney to Use Masonry ChimneysPrefabricated Chimneys Chimney SizeChimney Connector Guidelines Single-wall Chimney ConnectorsSecuring the Single-wall Connector to a Masonry Chimney Freestanding InstallationsFireplace Installations Above the FireplaceThrough the Fireplace Wall Pass-ThroughsFloor Protection for Fireplace Installation Floor ProtectionSafe Ways to Reduce Clearances Keep the Stove a Safe Distance from Sur Rounding MaterialsWall Shields Fireplace and Mantel Trim Shields Fireplace and Mantel Trim ClearancesDefiant Clearance Chart Stove Clearance Unprotected Surfaces Protected SurfacesDefiant Clearance Diagrams Unprotected Surfaces Protected SurfacesStove Heat Shields Distance from the Center of the Flue Collar to the Wall Defiant With Rear Heat Shield onlyAssembly Set Up Your StoveInstall Stove Legs Install the Optional Bottom Heat ShieldOperation Defiant ControlsDamper Directs Air Flow Within the Stove Single Air Control Regulates Heat Output and Burn TimeTwo Ways to Add Fuel Infra-Red Reflective Glass Panels For Clear Fire Viewing Andirons Help Protect the GlassBurn Only High-Quality Wood Surface Thermometer is a Valuable Guide to OperationDefiant Control Settings Use the Air Control Settings that Work Best for YouHigh-Efficiency Wood Burning With Catalytic Combustion Conditioning Your Stove Starting and Maintaining a Wood FireRefuel While the Embers Are Still Hot Add larger pieces of wood as the fire begins to burnAsh Disposal Draft Management Steel ChimneyIndoor/Outdoor Location Flue SizingDraft Testing Single VentingCreosote FuelNegative Pressure ConclusionMaintenance How to Adjust the Door Latches Adjust the Damper as NeededCheck the Operation Primary Air Shutter Tighten the Damper Handle as NeededInspection and Cleaning When to Suspect a Combustor ProblemRemoving and Cleaning the Combustor Catalytic ElementRemove the bricks and the brick retainer Replace the Stove Gaskets as Needed 30001693Annual Maintenance Adjust the Door Latch If NecessaryChimney System Permanent Defiant GasketsAppendix Catalytic Combustor Appendix Chimney and Fireplace Hazards For a fireplaceDefiant Woodburning Stove Defiant Woodburning Stove Model Shell Enamel Parts Defiant Color Warranty CFM Corporation

1945 specifications

Vermont Casting, founded in 1975, quickly established itself as a leader in the cast iron stove industry. However, the reference to 1945 in relation to Vermont Casting might allude to the beginnings of the American hearth industry post-World War II. In this pivotal period, the demand for home heating solutions soared, setting the stage for innovations in wood and gas stoves that would shape future designs.

Vermont Casting made a name for itself through a commitment to craftsmanship and durability. The company utilized high-quality cast iron, renowned for its excellent heat retention and even heating properties. This robust material allowed stoves to radiate warmth long after the fire had extinguished, making them an efficient choice for home heating.

One of the standout features of Vermont Casting stoves is their unique design which blends functionality with aesthetic appeal. The company offered both traditional and contemporary styles, appealing to a wide range of consumer tastes. With elaborate decorative patterns and a classic look, Vermont Casting stoves became a centerpiece in many homes, adding warmth not just through heat but also through design.

In terms of technology, Vermont Casting pioneered advancements in combustion efficiency. Their stoves often feature secondary combustion systems that ensure the complete burning of wood, which helps reduce smoke emissions and maximizes heat output. This not only complies with stringent environmental regulations but also makes their products eco-friendly.

Another notable characteristic of Vermont Casting stoves is their versatility. The company produces a range of models that cater to different fuels, including wood, gas, and pellets. This flexibility allows homeowners to choose the best heating solution for their specific needs and preferences.

Vermont Casting also places a strong emphasis on user comfort and ease of use. Many models come equipped with features like airwash systems for cleaner glass, lever handles for easy door operation, and ash pans for convenient cleanup. These thoughtful details enhance the overall user experience, making heating homes more efficient and enjoyable.

As the company has continued to innovate, it has remained committed to sustainability, focusing on creating products that are not only effective but also environmentally responsible. Vermont Casting's dedication to quality, technology, and design has cemented its status as a trusted name in the hearth industry, making it a preferred choice for consumers looking for both performance and style in their heating solutions.
Top Page Image Contents