Vermont Casting 1945 installation instructions Fireplace Installations, Above the Fireplace

Page 8

Defiant Woodburning Stove

Chimney

Flue

 

Elbow

Flue In-

 

 

ner

Slip Pipe

 

Standard

Thimble

 

Connector

 

Oval to

 

Round Adapter

 

 

Flue Collar

ST492

Fig. 6 An exploded view of the chimney connection in a free- standing masonry installation.

A special piece called the “thimble sleeve,” slightly smaller in diameter than standard connectors and most thimbles, will facilitate the removal of the chimney connector system for inspection and cleaning. (fig. 7) Thimble sleeves should be available from your local dealer.

To install a thimble sleeve, slide it into the breech until it is flush with the inner flue wall. Do not extend it into the actual flue passage, as this could interfere with the draft.

The thimble sleeve should protrude 1-2” (25-50 mm) into the room. Use furnace cement and thin gasketing to seal the sleeve in place in the thimble. Secure the chimney connector to the outer end of the sleeve with sheet metal screws.

Thimble Sleeve

Flue

Chimney Connector

Keep sleeve end flush with flue tile

ST243

Fig. 7 The thimble, made of either ceramic or metal, must be cemented securely in place.

Without a thimble, a suitable length of chimney con- nector can be extended through the breech to the inner face of the flue liner, and cemented securely in place. Additional pieces of connector are then attached with sheet metal screws.

Fireplace Installations

The chimney connector may be connected to the chimney above the fireplace opening or through the fireplace.

Above the Fireplace

The Defiant may be connected to a chimney above a fireplace opening. (Fig. 8) In such installations, the stove is positioned on the hearth in front of the fireplace and the chimney connector rises from the stove top and then angles ninety degrees back into the chimney. The chimney liner should extend to the point at which the chimney connector enters the chimney.

Check These

Clearances *

*

Mantel

• • • • • • •

Seal

 

This Off

ST244a

Fig. 8 In this installation, the chimney connector attaches to the chimney above the fireplace opening.

If the chimney connector in your installation enters the chimney above a fireplace, follow all the guidelines mentioned above for freestanding installations. In addi- tion, give special consideration to the following points:

•Check the clearance between the stove and the chimney connector, and any combustible trim or the mantel.

•Check the clearance between the chimney con- nector and the ceiling. The clearance should be at least 24” (610 mm).

•The fireplace damper must be sealed to prevent room air from escaping up the flue. However, it must be possible to re-open the damper to inspect or clean the chimney.

8

30001693

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Defiant Welcome Save These Instructions for Future ReferenceStory of the Defiant Table of ContentsInstallation Accessories Specifications Defiant, ModelChimney Height InstallationOutside Air What Kind of Chimney to Use Masonry ChimneysPrefabricated Chimneys Chimney SizeChimney Connector Guidelines Single-wall Chimney ConnectorsSecuring the Single-wall Connector to a Masonry Chimney Freestanding InstallationsFireplace Installations Above the FireplaceThrough the Fireplace Wall Pass-ThroughsFloor Protection for Fireplace Installation Floor ProtectionWall Shields Keep the Stove a Safe Distance from Sur Rounding MaterialsSafe Ways to Reduce Clearances Fireplace and Mantel Trim Shields Fireplace and Mantel Trim ClearancesDefiant Clearance Chart Stove Clearance Unprotected Surfaces Protected SurfacesDefiant Clearance Diagrams Unprotected Surfaces Protected SurfacesStove Heat Shields Distance from the Center of the Flue Collar to the Wall Defiant With Rear Heat Shield onlyAssembly Set Up Your StoveInstall Stove Legs Install the Optional Bottom Heat ShieldOperation Defiant ControlsTwo Ways to Add Fuel Single Air Control Regulates Heat Output and Burn TimeDamper Directs Air Flow Within the Stove Infra-Red Reflective Glass Panels For Clear Fire Viewing Andirons Help Protect the GlassBurn Only High-Quality Wood Surface Thermometer is a Valuable Guide to OperationHigh-Efficiency Wood Burning With Catalytic Combustion Use the Air Control Settings that Work Best for YouDefiant Control Settings Conditioning Your Stove Starting and Maintaining a Wood FireRefuel While the Embers Are Still Hot Add larger pieces of wood as the fire begins to burnAsh Disposal Draft Management Steel ChimneyIndoor/Outdoor Location Flue SizingDraft Testing Single VentingCreosote FuelNegative Pressure ConclusionMaintenance How to Adjust the Door Latches Adjust the Damper as NeededCheck the Operation Primary Air Shutter Tighten the Damper Handle as NeededInspection and Cleaning When to Suspect a Combustor ProblemRemoving and Cleaning the Combustor Catalytic ElementRemove the bricks and the brick retainer Replace the Stove Gaskets as Needed 30001693Annual Maintenance Adjust the Door Latch If NecessaryChimney System Permanent Defiant GasketsAppendix Catalytic Combustor Appendix Chimney and Fireplace Hazards For a fireplaceDefiant Woodburning Stove Defiant Woodburning Stove Model Shell Enamel Parts Defiant Color Warranty CFM Corporation

1945 specifications

Vermont Casting, founded in 1975, quickly established itself as a leader in the cast iron stove industry. However, the reference to 1945 in relation to Vermont Casting might allude to the beginnings of the American hearth industry post-World War II. In this pivotal period, the demand for home heating solutions soared, setting the stage for innovations in wood and gas stoves that would shape future designs.

Vermont Casting made a name for itself through a commitment to craftsmanship and durability. The company utilized high-quality cast iron, renowned for its excellent heat retention and even heating properties. This robust material allowed stoves to radiate warmth long after the fire had extinguished, making them an efficient choice for home heating.

One of the standout features of Vermont Casting stoves is their unique design which blends functionality with aesthetic appeal. The company offered both traditional and contemporary styles, appealing to a wide range of consumer tastes. With elaborate decorative patterns and a classic look, Vermont Casting stoves became a centerpiece in many homes, adding warmth not just through heat but also through design.

In terms of technology, Vermont Casting pioneered advancements in combustion efficiency. Their stoves often feature secondary combustion systems that ensure the complete burning of wood, which helps reduce smoke emissions and maximizes heat output. This not only complies with stringent environmental regulations but also makes their products eco-friendly.

Another notable characteristic of Vermont Casting stoves is their versatility. The company produces a range of models that cater to different fuels, including wood, gas, and pellets. This flexibility allows homeowners to choose the best heating solution for their specific needs and preferences.

Vermont Casting also places a strong emphasis on user comfort and ease of use. Many models come equipped with features like airwash systems for cleaner glass, lever handles for easy door operation, and ash pans for convenient cleanup. These thoughtful details enhance the overall user experience, making heating homes more efficient and enjoyable.

As the company has continued to innovate, it has remained committed to sustainability, focusing on creating products that are not only effective but also environmentally responsible. Vermont Casting's dedication to quality, technology, and design has cemented its status as a trusted name in the hearth industry, making it a preferred choice for consumers looking for both performance and style in their heating solutions.
Top Page Image Contents