Heat & Glo LifeStyle SUPREME-P-I30AU, SUPREME-N-I30AU Mantel and Wall Projections, SUPREME-I30AU

Page 20

1-1/2 in.

(38 mm)

BD

CD

SURROUND

APPLIANCE

SIDE VIEW

AD

SURROUND

APPLIANCE

TOP VIEW

MINIMUM FIREPLACE SIZE (1-1/2 IN. (38 mm) Surround Depth)

 

Location

 

SUPREME-I30AU

 

Inches

 

Millimeters

 

 

 

AD

Alternate Unit Width

29-1/16

 

738

BD

Alternate Unit Depth

13-7/8

 

352

CD

Alternate Unit Height

19-1/16

 

484

*Note: If exhaust collar on insert and fireplace damper do not line up, add 4 in. (102 mm) to minimum fireplace height for bends in vent pipe.

Figure 5.3 Fireplace Opening - Deep Surround

B. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as specified. Framing or finishing material closer than the minimums listed must be construct- ed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).

Clearance to combustible material under the insert is 1/4 in. (6 mm). Clearance from top of fireplace opening for combustibles extending 12 in. (305 mm) max. is 12 in (305 mm)

•Use leveling legs to raise insert minimum 1/4 in. (6 mm) above combustible material or outer wrap of factory built firebox.

Combustible facings must not extend behind the insert surround. For non-combustible material specifications refer to Section 1.E.

NON-COMBUSTIBLE FACING

 

12 in.

 

(305 mm)

 

MAX.

 

MINIMUM CLEARANCE

TO COMBUSTIBLE

12 in.

MANTEL OR

(305 mm)

PROJECTION

MIN.

Figure 5.4 Mantel Clearances or Other Combustibles Above Appliances

20

Heat & Glo • Supreme-N-I30AU, Supreme-P-I30AU • 2222-900 Rev. P • 6/12

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Models SUPREME-N-I30AU SUPREME-P-I30AU SAI Global Ref No GSCS20181What to do if you smell gas HOT SurfacesMODELSSupreme-N-I30AU,Supreme-P-I30AU Congratulations Homeowner Reference InformationTable of Contents User GuideAustralian Warranty Information Limited Lifetime WarrantyOther Rights Perth Listing and Code Approvals Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesIPI Battery Tray/Battery Installation Clear SpaceBefore Lighting Fireplace Module ResetNine Hour Safety Shutdown Feature Lighting Instructions IPI Final inspection byWhat to do if YOU Smell GAS GAS ValveAfter Appliance is Lit Frequently Asked QuestionsIssue Solutions Maintenance and Service Maintenance Tasks-Service Technician Gasket Seal and Glass Assembly InspectionLogs FireboxGetting Started Typical Appliance SystemInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Fireplace Size Requirements Minimum Fireplace OpeningTOP View Front View Side View Fireplace OpeningMantel and Wall Projections SUPREME-I30AUTermination Locations Vent Termination Minimum ClearancesInstallation Preparation Installing Vent Pipe and Appliance Connecting Vent PipeVent Limits Venting ComponentsPage Placing, Securing and Leveling Appliance Installing Adaptor and Termination Cap MasonryFactory Built Damper Flashing Kit OptionalModel Flue Termination Approval Direct Vent Flex Liner Accessory Kits Vent Kits ComponentsHeat Shield Requirements for Horizontal Termination For Horizontal Terminations using the SLP-TRAP2Flue Termination Must adhere to pipe clearances Colinear to Coaxial Adapter Must adhere to pipe clearances Alternate built-in options Minimum construction requirementsSLP-TVHW Minimum TotalLink Adapter Maximum TotalNON-COMBUSTIBLE Base Under Unit Flue Starter Plate Gas Information Gas ConnectionElectrical Information Wiring RequirementsIntelliFire PlusTM Ignition System Wiring Optional Accessories Requirements Fan Wiring DiagramKit Contents Installation PrecautionsREM300-HNG-AU Instructions Fireplace Specific InformationChanging Temperature Scale Installation of Remote Control HousingProgramming the RC300AU to the Control Module AUX300CE Module InstallationFan Installation Idle When Remote is in on Mode Standby modeDisplay Screen Function ButtonsAbout on Mode About OFF ModeAdjusting Flame Height Adjusting Fan SpeedAdjusting Thermostat Adjusting TimerSetting the Child Lock Power OutageFrequently Asked Questions/Troubleshooting Symptom Possible Cause Corrective ActionFinishing Clearances to Mantels or other Combustibles above ApplianceAppliance Setup Install the Log Assembly Pilot AS Sembly LOG PIN Grate TinesCorner LOG Flush With LOG TAB For LOG #6Latches Air Shutter SettingAir Shutter Settings Required to Complete Insert Installation Decorative Fronts and SurroundsIPI+ Optional AccessoriesOptional RC300AU Remote Optional BRICK-SI30 Kit IntelliFire Plus Ignition System TroubleshootingSymptom Possible Cause Corrective Action If the pilot continues Maintenance Tasks Inspect Maintenance TasksAppliance Dimension Diagram Model DimensionsReference Materials SUPREME-I30-AUService Parts Log Set AssemblyMetal Insert, IPI Description Comments Part Number#15 Valve Assembly SUPREME-N-I30AU, SUPREME-P-I30AU Contact Information

SUPREME-P-I30AU, SUPREME-N-I30AU specifications

The Heat & Glo LifeStyle SUPREME-P-I30AU and SUPREME-N-I30AU are premium gas fireplaces designed to create a cozy, inviting atmosphere while offering modern technological features and exceptional performance. These units are perfect additions to any home, blending elegance with practicality.

One of the standout features of the SUPREME series is its versatile design. The fireplaces are available in both linear and traditional styles, allowing homeowners to choose the configuration that best complements their living space. With a sleek, modern aesthetic, the SUPREME-P-I30AU offers a panoramic view of the flames, making it a captivating focal point in any room.

These models are equipped with advanced heating capabilities. The powerful heat output ensures that the fireplace can effectively warm spaces ranging from medium to large. Homeowners can enjoy optimal comfort during the colder months, knowing they have a reliable source of heat at their disposal.

Another key characteristic is the innovative IntelliFire technology, which automates the ignition system and monitors the flame to ensure safe and efficient operation. This feature not only enhances the user experience but also minimizes energy consumption by allowing the unit to alternate between different flame settings based on the home's heating needs.

Installation is made easy with the SUPREME series, thanks to its flexible venting options. The fireplaces can be vented either vertically or horizontally, making them suitable for various home layouts. Additionally, the units are designed for easy access to components, simplifying maintenance and ensuring longevity.

Both the SUPREME-P-I30AU and SUPREME-N-I30AU come with a range of aesthetic options for customization, including different media choices such as logs, glass, and stones. This allows users to tailor the appearance of their fireplace to match their personal style and home décor.

Safety features are paramount in the design of the SUPREME series. The fireplaces include advanced safety controls and thermal sensors to prevent overheating and ensure peace of mind for users.

In summary, the Heat & Glo LifeStyle SUPREME-P-I30AU and SUPREME-N-I30AU stand out due to their stylish designs, powerful heating capabilities, innovative technologies, and customizable options, making them ideal choices for anyone looking to enhance their home with a functional and aesthetically pleasing gas fireplace.
Top Page Image Contents