Heat & Glo LifeStyle SUPREME-N-I30AU About on Mode, About OFF Mode, Turning on the Fireplace

Page 43

About ON Mode

•All functions can be accessed when the remote control is in the ON mode.

•Only active functions will be displayed when the remote control is in the ON mode. For example: if the fan is the only function that’s active, the fan icon and flame will be the only icon shown in the display.

About OFF Mode

Only the following functions can be accessed in the OFF mode:

•AUX1

•AUX2

Only active functions will be displayed when the remote control is in the OFF mode.

Turning ON the Fireplace

•Press the POWER button to turn the fireplace ON. The fireplace will first ignite the pilot. Once the pilot flame is estabilshed the main burner will be lit.

NOTICE: Whenever the fireplace is cycled from OFF to ON, the main burner will light on high for 10 seconds be- fore returning to the previous user setting.

Adjusting Flame Height

•Press the MENU button to activate the menu.

•Using the UP and DOWN arrows highlight the FLAME icon and press SELECT.

•Use the UP and DOWN arrows to adjust the FLAME HEIGHT, then press SELECT. The FLAME HEIGHT can be adjusted to 5 different settings.

NOTICE: FLAME HEIGHT will not be adjustable for first ten seconds when fireplace is turned on.

NOTICE: The system will remember the previous FLAME HEIGHT setting and will automatically adjust after 10 seconds.

Adjusting Fan Speed

•Press the MENU button to activate the menu.

•Using the UP and DOWN arrows highlight the FAN icon and press SELECT.

•Use the UP and DOWN arrows to adjust the FAN SPEED, then press SELECT. The FAN SPEED can be adjusted to 3 different settings: HIGH, MEDIUM, LOW.

NOTICE: The fan has a timer built into the control module. After the fireplace is turned ON the timer will wait for 3 minutes before turning on the fan. In addition, the fan will remain on for 12 minutes after the fireplace has been turned OFF.

NOTICE: Whenever the fan is turned ON, the FAN will start up on the high setting for 10 seconds before adjusting to the previous user setting.

AUX1 Function (Unit dependent Function)

•Press the MENU button to activate the menu.

•Using the UP and DOWN arrows highlight the AUX1 icon and press SELECT.

•Use the UP and DOWN arrows to adjust the AUX1 output, then press SELECT. The AUX1 function can be adjusted to 4 different settings: HI, MED, LOW and OFF.

AUX2 Function (Unit dependent Function)

•Press the MENU button to activate the menu.

•Using the UP and DOWN arrows highlight the AUX2 icon and press SELECT.

•Use the UP and DOWN arrows to turn the AUX2 ON or OFF, then press SELECT. The AUX2 function can be either be turned ON or OFF.

NOTICE: The system will remember the previous AUX1 and AUX2 setting from the menu. However, when the fire- place is turned OFF both AUX1 and AUX2 will be turned off. AUX and AUX2 can be activated when the flame is off from the remote’s OFF mode. When the fireplace is turned back ON the AUX1 and AUX2 settings will be restored to the previous ON setting.

Heat & Glo • Supreme-N-I30AU, Supreme-P-I30AU • 2222-900 Rev. P • 6/12

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents HOT Surfaces Models SUPREME-N-I30AU SUPREME-P-I30AUSAI Global Ref No GSCS20181 What to do if you smell gasMODELSSupreme-N-I30AU,Supreme-P-I30AU Homeowner Reference Information CongratulationsUser Guide Table of ContentsLimited Lifetime Warranty Australian Warranty InformationOther Rights Perth Listing and Code Approvals Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches IPI Battery Tray/Battery InstallationNine Hour Safety Shutdown Feature Module ResetBefore Lighting Fireplace GAS Valve Lighting Instructions IPIFinal inspection by What to do if YOU Smell GASIssue Solutions Frequently Asked QuestionsAfter Appliance is Lit Maintenance and Service Firebox Maintenance Tasks-Service TechnicianGasket Seal and Glass Assembly Inspection LogsTypical Appliance System Getting StartedTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Minimum Fireplace Opening Fireplace Size RequirementsFireplace Opening TOP View Front View Side ViewSUPREME-I30AU Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Vent LimitsPage Placing, Securing and Leveling Appliance Damper Flashing Kit Optional Installing Adaptor and Termination CapMasonry Factory BuiltModel Flue Termination Approval Vent Kits Components Direct Vent Flex Liner Accessory KitsFlue Termination For Horizontal Terminations using the SLP-TRAP2Heat Shield Requirements for Horizontal Termination Must adhere to pipe clearances Colinear to Coaxial Adapter Must adhere to pipe clearances Minimum construction requirements Alternate built-in optionsMaximum Total SLP-TVHWMinimum Total Link AdapterNON-COMBUSTIBLE Base Under Unit Flue Starter Plate Gas Connection Gas InformationIntelliFire PlusTM Ignition System Wiring Wiring RequirementsElectrical Information Fan Wiring Diagram Optional Accessories RequirementsFireplace Specific Information Kit ContentsInstallation Precautions REM300-HNG-AU InstructionsInstallation of Remote Control Housing Changing Temperature ScaleFan Installation AUX300CE Module InstallationProgramming the RC300AU to the Control Module Function Buttons Idle When Remote is in on ModeStandby mode Display ScreenAdjusting Fan Speed About on ModeAbout OFF Mode Adjusting Flame HeightPower Outage Adjusting ThermostatAdjusting Timer Setting the Child LockSymptom Possible Cause Corrective Action Frequently Asked Questions/TroubleshootingClearances to Mantels or other Combustibles above Appliance FinishingAppliance Setup Pilot AS Sembly LOG PIN Grate Tines Install the Log AssemblyFor LOG #6 Corner LOG Flush With LOG TABAir Shutter Settings Air Shutter SettingLatches Decorative Fronts and Surrounds Required to Complete Insert InstallationOptional RC300AU Remote Optional BRICK-SI30 Kit Optional AccessoriesIPI+ Symptom Possible Cause Corrective Action TroubleshootingIntelliFire Plus Ignition System If the pilot continues Inspect Maintenance Tasks Maintenance TasksSUPREME-I30-AU Appliance Dimension DiagramModel Dimensions Reference MaterialsDescription Comments Part Number Service PartsLog Set Assembly Metal Insert, IPI#15 Valve Assembly SUPREME-N-I30AU, SUPREME-P-I30AU Contact Information

SUPREME-P-I30AU, SUPREME-N-I30AU specifications

The Heat & Glo LifeStyle SUPREME-P-I30AU and SUPREME-N-I30AU are premium gas fireplaces designed to create a cozy, inviting atmosphere while offering modern technological features and exceptional performance. These units are perfect additions to any home, blending elegance with practicality.

One of the standout features of the SUPREME series is its versatile design. The fireplaces are available in both linear and traditional styles, allowing homeowners to choose the configuration that best complements their living space. With a sleek, modern aesthetic, the SUPREME-P-I30AU offers a panoramic view of the flames, making it a captivating focal point in any room.

These models are equipped with advanced heating capabilities. The powerful heat output ensures that the fireplace can effectively warm spaces ranging from medium to large. Homeowners can enjoy optimal comfort during the colder months, knowing they have a reliable source of heat at their disposal.

Another key characteristic is the innovative IntelliFire technology, which automates the ignition system and monitors the flame to ensure safe and efficient operation. This feature not only enhances the user experience but also minimizes energy consumption by allowing the unit to alternate between different flame settings based on the home's heating needs.

Installation is made easy with the SUPREME series, thanks to its flexible venting options. The fireplaces can be vented either vertically or horizontally, making them suitable for various home layouts. Additionally, the units are designed for easy access to components, simplifying maintenance and ensuring longevity.

Both the SUPREME-P-I30AU and SUPREME-N-I30AU come with a range of aesthetic options for customization, including different media choices such as logs, glass, and stones. This allows users to tailor the appearance of their fireplace to match their personal style and home décor.

Safety features are paramount in the design of the SUPREME series. The fireplaces include advanced safety controls and thermal sensors to prevent overheating and ensure peace of mind for users.

In summary, the Heat & Glo LifeStyle SUPREME-P-I30AU and SUPREME-N-I30AU stand out due to their stylish designs, powerful heating capabilities, innovative technologies, and customizable options, making them ideal choices for anyone looking to enhance their home with a functional and aesthetically pleasing gas fireplace.
Top Page Image Contents