GE 60-883-95R Plugging in the Power, Powering up the System, Adjusting the Speaker Volume

Page 9

To Home

Phone Jack

To Phone or Answering

Machine

To AC Outlet

Power Switch

LINE

PHONE

Figure 2. Connecting the CareGard System to the Phone Line

Plugging in the Power

The panel is pre-wired for power. Simply plug the transformer into an available standard outlet (110 VAC).

Important !

Make sure the outlet is not controlled by a switch or part of a ground fault interrupt circuit (GFIC).

Powering up the System

Turn the Power switch on the back of the panel to On. The panel voice should announce “Hello, system X is OK.”

Note

After power up the system may announce “System Low Battery” and the Status light will flash. It may take several hours for the battery to fully change after it is initially plugged in.

Adjusting the Speaker Volume

The Volume button on the front of the panel controls the volume of announcements from the speaker and the volume during a 2-way talk session.

Adjust the built-in speaker volume using the Volume button on the front of the panel. Each time the Volume button is pressed it increases the speaker volume one level and announces the volume level.

Adjust the volume the same way during a 2-way talk session.

Basic Operation The main function of the CareGard system is to respond to the wrist or pendant panic and the panel Call button.

To activate a portable panic sensor:

•Wrist Panic - Press the button until its red light blinks.

•Pendant Panic - Press and hold the button for 2 seconds.

To activate the panel Call button:

Depending on how Option 21 (Call Button Enable) is set, the Call button operates with a single press or two presses. If Option 21 is set to off, the panel Call button cannot be used to initiate an emergency call.

Basic Operation

4

Image 9

Contents CareGard FCC Part 15 Information to the User GE InterlogixContents Activity Check Medication RemindersAdding/Replacing Sensors Sensor Testing Phone Communication Testing TroubleshootingDeleting Sensors System Monitoring Special Installation Requirements ETL Listed InstallationsCentral Station Reporting Multi-Purpose Panic Control PanelPlugging in the Phone Line Locating the PanelLine Seizure No Line SeizurePowering up the System Plugging in the PowerAdjusting the Speaker Volume To activate a portable panic sensorMaster Access Code Access CodesUtility Access Code 1 Dealer Code Utility Access Code 2 Installer CodeEntering Program Mode Setting the ClockChanging an Access Code ¾ To hear the current setting for each option Numbered Options Settings¾ To change an option setting Function Default Range Desired SettingRange = On/Off Default = On Option 1 Panel Voice¾ To turn Panel Voice On or Off Option 3 Primary Phone Number Option 2 Account NumberOption 4 Secondary Phone Number Option 5 Numeric Pager/Voice Event Notification PhoneOption 7 Downloader Phone Number Phone Mod 1 SettingsOption 8 Phone Lock Option 9 Downloader CodePhone Mod 3 Settings Phone Mod 2 SettingsOption 11 Phone Mod Option 12 Numeric Pager/Voice Event Notification PhoneOption 17 AC Power Failure Report Option 15 RF TimeoutOption 13 Dtmf Dialing Option 14 Auto Phone TestRange = On/Off Default = Option 18 CPU Low Battery ReportRing/Hang/Ring Settings Option 19 Fail to CommunicateOption 22 Downloader Enable Option 21 Call Button EnableOption 26 AVM Mode Option 23 300 BaudRange = 3-6 Default = Option 28 Access Code LengthAccess Code Length Defaults Option 27 RF Jam DetectOption 31 Programming Report Option 30 Demo ModeOption 32 Supervisory Time Option 33 Modem SensitivityOption 39 No Audio on Alarm Cancel Option 38 Alarm Cancel TimeoutOption 36 Manual Mic Gain Option 37 VOX Receiver GainResetting Memory to Defaults Exiting Programming ModeUsing CareGard with Activity Check Set Option 42 Siren Time OutSetting up Medication Reminders Home and AwayAcknowledging Medication Reminders Supervised vs. Not Supervised Adding Replacing SensorsProgramming Sensors Sensor Type To ProgramDoor/Window Sensor type possibilities Sensor Type To Trip Sensor Type Options Backup Battery AC PowerDeleting Sensors SystemReplacing the Backup Battery Sensor Low Battery¾ To replace the backup battery Sensor Supervisory FailureAutomatic Phone Test Sensor TestingPhone Test Central Station CommunicationVoice Event Notification Pager CommunicationRemote Phone Operation Pager Reporting MessageRemote Phone Operation System Function Phone CommandProblem Solution Troubleshooting GuideNumerics Index