GE 60-883-95R Option 18 CPU Low Battery Report, Option 19 Fail to Communicate

Page 18

Option 18: CPU Low Battery Report

 

 

Range = On/Off (Default = On)

Determines whether the panel sends a low CPU battery report to the central

¾ To Add or Delete CPU Low Battery

station when the panel backup battery voltage drops below 5.4 volts (on), or

 

Report:

not (off).

 

1.

Press Add or Delete.

A CPU Low Battery Report is also sent at the time specified by Option 32:

2.

Press Option #.

Supervisory Time. When the backup battery is restored a system battery

3.

Press 1, then 8.

restoral report will be sent to the central station.

 

 

4.

Press Done.

Note

 

 

 

 

 

CPU Low Battery Report must be turned on for ETL (UL 1635) listed systems.

 

 

 

 

 

 

 

 

 

Option 19: Fail to Communicate

 

 

Range = On/Off (Default = On)

 

 

 

 

 

Determines whether the panel sounds trouble beeps if it is unable to success-

¾ To Add or Delete Fail to Communicate:

fully send a report to a central station or pager (on), or not (off).

 

1.

Press Add or Delete.

Note

 

2.

Press Option #.

The panel will try each programmed phone number 8 times before announcing a

3.

Press 1, then 8.

system phone communication failure.

 

If Option 11 is set to 6 or 7 after 3 failed attempts with the phone 1 number a

4.

Press Done.

phone communication failure occurs

 

 

 

 

 

 

 

 

 

 

 

Option 20: Ring/Hang/Ring

 

 

Range = On/Off (Default = 1)

 

 

 

 

 

Determines when the panel answers a remote phone access call. Depending

¾ To program Ring/Hang/Ring:

on whether an answering machine exists at the panel location, off-site access

1.

Press Add.

to the panel can be achieved with a series of phone calls or just one. Table 5

2.

Press Option #.

shows the available settings.

 

¾ For off-site access where an answering machine exists, the user

3.

Press 2, then 0.

4.

Enter a Ring/Hang/Ring setting using the

must perform the following steps:

 

1. Call the panel location.

 

 

numbered buttons.

 

5.

Press Done.

2. Let the Phone ring once, then hang up.

 

 

 

 

 

3. Wait at least 10 seconds but not more than 40, then call the panel location

 

 

 

again. The panel should answer on the first ring.

 

 

 

 

• If set to 1, perform steps 1-3 once.

 

 

 

 

• If set to 2, perform steps 1-3 twice.

 

 

 

 

• If set to 3, perform steps 1-3 three times.

 

 

 

 

See “Phone Communication” in the Testing the System section of this man-

 

 

 

ual for the commands used for remote phone control.

 

 

 

 

Note

 

 

 

 

For off-site access where an answering machine does not exist, the user simply

 

 

 

calls the panel location once and listens for 10 rings. The panel should answer

 

 

 

after the tenth ring.

 

 

 

 

 

 

 

 

 

Table 5: Ring/Hang/Ring Settings

 

 

 

 

 

Setting

Control Panel answers after:

 

 

 

 

 

 

 

 

 

 

1

ring/hang/ring or 10 rings

 

 

 

 

 

 

2

ring/hang/ring/hang/ring or 10 rings

 

 

 

 

 

 

3

ring/hang/ring/hang/ring/hang/ring or 10

 

 

 

rings

 

 

 

 

 

 

 

 

 

 

4

10 rings

 

 

 

 

 

 

 

 

Off

Disabled - no remote (off-site) access

 

 

 

 

 

 

 

13

Programming Options

Page 17 Page 19
Image 18
Page 17 Page 19
Contents CareGard GE Interlogix FCC Part 15 Information to the UserContents Activity Check Medication RemindersAdding/Replacing Sensors Sensor Testing Phone Communication Testing TroubleshootingDeleting Sensors System Monitoring Special Installation Requirements ETL Listed InstallationsCentral Station Reporting Control Panel Multi-Purpose PanicLine Seizure Locating the PanelPlugging in the Phone Line No Line SeizureAdjusting the Speaker Volume Plugging in the PowerPowering up the System To activate a portable panic sensorUtility Access Code 1 Dealer Code Access CodesMaster Access Code Utility Access Code 2 Installer CodeEntering Program Mode Setting the ClockChanging an Access Code ¾ To change an option setting Numbered Options Settings¾ To hear the current setting for each option Function Default Range Desired SettingRange = On/Off Default = On Option 1 Panel Voice¾ To turn Panel Voice On or Off Option 4 Secondary Phone Number Option 2 Account NumberOption 3 Primary Phone Number Option 5 Numeric Pager/Voice Event Notification PhoneOption 8 Phone Lock Phone Mod 1 SettingsOption 7 Downloader Phone Number Option 9 Downloader CodeOption 11 Phone Mod Phone Mod 2 SettingsPhone Mod 3 Settings Option 12 Numeric Pager/Voice Event Notification PhoneOption 13 Dtmf Dialing Option 15 RF TimeoutOption 17 AC Power Failure Report Option 14 Auto Phone TestRing/Hang/Ring Settings Option 18 CPU Low Battery ReportRange = On/Off Default = Option 19 Fail to CommunicateOption 26 AVM Mode Option 21 Call Button EnableOption 22 Downloader Enable Option 23 300 BaudAccess Code Length Defaults Option 28 Access Code LengthRange = 3-6 Default = Option 27 RF Jam DetectOption 32 Supervisory Time Option 30 Demo ModeOption 31 Programming Report Option 33 Modem SensitivityOption 36 Manual Mic Gain Option 38 Alarm Cancel TimeoutOption 39 No Audio on Alarm Cancel Option 37 VOX Receiver GainUsing CareGard with Activity Check Set Exiting Programming ModeResetting Memory to Defaults Option 42 Siren Time OutSetting up Medication Reminders Home and AwayAcknowledging Medication Reminders Programming Sensors Adding Replacing SensorsSupervised vs. Not Supervised Sensor Type To ProgramDoor/Window Sensor type possibilities Sensor Type To Trip Sensor Type Options Deleting Sensors AC PowerBackup Battery System¾ To replace the backup battery Sensor Low BatteryReplacing the Backup Battery Sensor Supervisory FailurePhone Test Sensor TestingAutomatic Phone Test Central Station CommunicationRemote Phone Operation Pager CommunicationVoice Event Notification Pager Reporting MessageSystem Function Phone Command Remote Phone OperationTroubleshooting Guide Problem SolutionIndex Numerics
Top Page Image Contents