GE 60-883-95R Option 1 Panel Voice, Range = On/Off Default = On, ¾ To turn Panel Voice On or Off

Page 13

Table 1: Numbered Options Settings

	No.	Function	Default	Range	Desired Setting


	21	Call Button Enable	1	1, 2, Off

	22	Downloader Enable (Not Currently Available)	On	On/Off

	23	300 Baud	On	On/Off

	24	Audio Verification	On	On/Off

	25	Trouble Beeps	On	On/Off

	26	AVM Mode	Off	On/Off

	27	RF Jam Detect	Off	On/Off

	28	Access Code Length	4	3-6

	29	RF Phone Answer	On	On/Off

	30	Demo Mode	Off	On/Off

	31	Programming Report	Off	On/Off

	32	Supervisory Time	12:00 A.M.	Any time of day

	33	Modem Sensitivity	Off	On/Off

	34	VOX Mic Gain	14	01-64

	35	VOX Gain Range	20	01-64

	36	Manual Mic Gain	64	01-64

	37	VOX Receiver Gain	6	01-10

	38	Alarm Cancel Timeout	005 minutes	003-254
				255 = Off

	39	No Audio after Cancel	Off	On/Off

	40	Report Medication Failures At Supervisory Time	Off	On/Off

	41	No Activity Hours	Off	02-48

	42	Siren Time Out	4 minutes	002-254

	43	House Code	A	A-P


	Option 1: Panel Voice			Range = On/Off (Default = On)

When this option is Off and Option 21 is set to 2 the panel will not announce “Press again for emergency call, or press Status to cancel.” This option is ignored when the panel is in program mode.

¾To turn Panel Voice On or Off:

1. Press Add or Delete.

2. Press Option #.

3. Press 0, then 1.

4. Press Done.

Programming Options

8

Image 13

Contents CareGard FCC Part 15 Information to the User GE InterlogixContents Medication Reminders Activity CheckAdding/Replacing Sensors Troubleshooting Sensor Testing Phone Communication TestingDeleting Sensors System Monitoring ETL Listed Installations Special Installation RequirementsCentral Station Reporting Multi-Purpose Panic Control PanelPlugging in the Phone Line Locating the PanelLine Seizure No Line SeizurePowering up the System Plugging in the PowerAdjusting the Speaker Volume To activate a portable panic sensorMaster Access Code Access CodesUtility Access Code 1 Dealer Code Utility Access Code 2 Installer CodeSetting the Clock Entering Program ModeChanging an Access Code ¾ To hear the current setting for each option Numbered Options Settings¾ To change an option setting Function Default Range Desired SettingOption 1 Panel Voice Range = On/Off Default = On¾ To turn Panel Voice On or Off Option 3 Primary Phone Number Option 2 Account NumberOption 4 Secondary Phone Number Option 5 Numeric Pager/Voice Event Notification PhoneOption 7 Downloader Phone Number Phone Mod 1 SettingsOption 8 Phone Lock Option 9 Downloader CodePhone Mod 3 Settings Phone Mod 2 SettingsOption 11 Phone Mod Option 12 Numeric Pager/Voice Event Notification PhoneOption 17 AC Power Failure Report Option 15 RF TimeoutOption 13 Dtmf Dialing Option 14 Auto Phone TestRange = On/Off Default = Option 18 CPU Low Battery ReportRing/Hang/Ring Settings Option 19 Fail to CommunicateOption 22 Downloader Enable Option 21 Call Button EnableOption 26 AVM Mode Option 23 300 BaudRange = 3-6 Default = Option 28 Access Code LengthAccess Code Length Defaults Option 27 RF Jam DetectOption 31 Programming Report Option 30 Demo ModeOption 32 Supervisory Time Option 33 Modem SensitivityOption 39 No Audio on Alarm Cancel Option 38 Alarm Cancel TimeoutOption 36 Manual Mic Gain Option 37 VOX Receiver GainResetting Memory to Defaults Exiting Programming ModeUsing CareGard with Activity Check Set Option 42 Siren Time OutHome and Away Setting up Medication RemindersAcknowledging Medication Reminders Supervised vs. Not Supervised Adding Replacing SensorsProgramming Sensors Sensor Type To ProgramDoor/Window Sensor type possibilities Sensor Type To Trip Sensor Type Options Backup Battery AC PowerDeleting Sensors SystemReplacing the Backup Battery Sensor Low Battery¾ To replace the backup battery Sensor Supervisory FailureAutomatic Phone Test Sensor TestingPhone Test Central Station CommunicationVoice Event Notification Pager CommunicationRemote Phone Operation Pager Reporting MessageRemote Phone Operation System Function Phone CommandProblem Solution Troubleshooting GuideNumerics Index