GE 60-883-95R Option 36 Manual Mic Gain, Option 37 VOX Receiver Gain, Option 41 Activity Check

Page 22

Option 36: Manual Mic Gain

 

Range = 01-64 (Default = 64)

Determines the mic gain level (sensitivity) during 2-way audio sessions,

¾ To program Manual Mic Gain:

when manually switching between listen and talk.

1.

Press Add.

Room size, acoustics, and furnishings where the panel is located will influ-

2.

Press Option #.

ence the setting. The available settings are 01 (low) to 64 (high). Entries

3.

Press 3, then 6.

must be 2 digits.

4.

Enter the desired Manual Mic Gain using

 

 

 

the numbered buttons.

 

5.

Press Done.

 

 

 

Option 37: VOX Receiver Gain

 

Range = 01-10 (Default = 6)

 

 

Determines the receiver gain level during 2-way audio sessions.

¾ To program VOX Receiver Gain:

If the VOX is switching the speaker on when the central station operator is

1.

Press Add.

not talking, lower both this setting and Option 34: VOX Mic Gain. If the

2.

Press Option #.

VOX is not switching the speaker on when the central station operator is

3.

Press 3, then 7.

talking, raise this setting and lower Option 34: VOX Mic Gain.

4.

Enter the desired VOX Receiver Gain using

This option can be set from 01 to 10. Entries must be 2 digits.

 

the numbered buttons.

Note

 

5.

Press Done.

Changing this setting does not affect speaker volume.

 

 

 

 

Option 38: Alarm Cancel Timeout

Range = (Off), 003-254 Min (Default = 005)

 

 

Determines the number of minutes the user has to cancel an alarm. If the

¾ To program Alarm Cancel Timeout:

alarm is cancelled within the Alarm Cancel Timeout period, an alarm cancel

1.

Press Add.

report is generated.

2.

Press Option #.

Note

3.

Press 3, then 8.

If this option is Off alarms cannot be cancelled and the panel will not announce “or

press Status to cancel.”

4.

Enter the desired Alarm Cancel Timeout

 

 

using the numbered buttons.

 

5.

Press Done.

 

 

 

Option 39: No Audio on Alarm Cancel

 

Range = On/Off (Default = Off)

 

 

Determines if an audio session occurs after an alarm has been cancelled. By

¾ To Add or Delete No Audio on Alarm Can-

default an audio session will occur after a cancelled alarm. Turn this option

 

cel:

on to disable audio after an alarm cancel.

1.

Press Add.

 

2.

Press Option #.

 

3.

Press 3, then 9.

 

4.

Press Done.

 

 

 

Option 40: Report Medication Failures at Supervisory Time

 

Range = On/Off (Default = Off)

 

 

If this option is on, a failure to take medication is reported to the central

¾ To Add or Delete Report Medication Fail-

monitoring station at Supervisory Time. When this option is off (default) a

 

ure at Supervisory Time:

failure to take medication is reported immediately. Pager and voice event

1.

Press Add.

notifications occur immediately.

2.

Press Option #.

 

 

3.

Press 4, then 0.

 

4.

Press Done.

 

 

 

Option 41: Activity Check

 

Range = 02-48 Hours (Default = Off)

 

 

This option determines the number of hours that may pass without the Care-

¾ To Add or Delete Activity Timer:

Gard system detecting activity before a no activity alarm/report is generated.

1. Press Add.

 

2.

Press Option #.

 

3.

Press 4, then 1.

 

4.

Enter the desired No Activity Hours using

 

 

the numbered buttons.

 

5.

Press Done.

 

 

 

17

Programming Options

Page 21 Page 23
Image 22
Page 21 Page 23
Contents CareGard GE Interlogix FCC Part 15 Information to the UserContents Medication Reminders Activity CheckAdding/Replacing Sensors Troubleshooting Sensor Testing Phone Communication TestingDeleting Sensors System Monitoring ETL Listed Installations Special Installation RequirementsCentral Station Reporting Control Panel Multi-Purpose PanicLine Seizure Locating the PanelPlugging in the Phone Line No Line SeizureAdjusting the Speaker Volume Plugging in the PowerPowering up the System To activate a portable panic sensorUtility Access Code 1 Dealer Code Access CodesMaster Access Code Utility Access Code 2 Installer CodeSetting the Clock Entering Program ModeChanging an Access Code ¾ To change an option setting Numbered Options Settings¾ To hear the current setting for each option Function Default Range Desired SettingOption 1 Panel Voice Range = On/Off Default = On¾ To turn Panel Voice On or Off Option 4 Secondary Phone Number Option 2 Account NumberOption 3 Primary Phone Number Option 5 Numeric Pager/Voice Event Notification PhoneOption 8 Phone Lock Phone Mod 1 SettingsOption 7 Downloader Phone Number Option 9 Downloader CodeOption 11 Phone Mod Phone Mod 2 SettingsPhone Mod 3 Settings Option 12 Numeric Pager/Voice Event Notification PhoneOption 13 Dtmf Dialing Option 15 RF TimeoutOption 17 AC Power Failure Report Option 14 Auto Phone TestRing/Hang/Ring Settings Option 18 CPU Low Battery ReportRange = On/Off Default = Option 19 Fail to CommunicateOption 26 AVM Mode Option 21 Call Button EnableOption 22 Downloader Enable Option 23 300 BaudAccess Code Length Defaults Option 28 Access Code LengthRange = 3-6 Default = Option 27 RF Jam DetectOption 32 Supervisory Time Option 30 Demo ModeOption 31 Programming Report Option 33 Modem SensitivityOption 36 Manual Mic Gain Option 38 Alarm Cancel TimeoutOption 39 No Audio on Alarm Cancel Option 37 VOX Receiver GainUsing CareGard with Activity Check Set Exiting Programming ModeResetting Memory to Defaults Option 42 Siren Time OutHome and Away Setting up Medication RemindersAcknowledging Medication Reminders Programming Sensors Adding Replacing SensorsSupervised vs. Not Supervised Sensor Type To ProgramDoor/Window Sensor type possibilities Sensor Type To Trip Sensor Type Options Deleting Sensors AC PowerBackup Battery System¾ To replace the backup battery Sensor Low BatteryReplacing the Backup Battery Sensor Supervisory FailurePhone Test Sensor TestingAutomatic Phone Test Central Station CommunicationRemote Phone Operation Pager CommunicationVoice Event Notification Pager Reporting MessageSystem Function Phone Command Remote Phone OperationTroubleshooting Guide Problem SolutionIndex Numerics
Top Page Image Contents