GE 60-883-95R installation instructions Sensor Type To Trip Sensor Type Options

Page 27

Note

The sensor number can be changed during program mode by pressing the num- bered keys after pressing the sensor button. Sensors can be numbered 01 to 24. Be sure to enter 0 before the number for sensor numbers 1 to 9. The sensor number cannot be changed after it has been programmed.

To Add or Replace a Sensor using the Programming Buttons under the Panel Cover

1.Open the front cover.

2.Enter the Utility 1 or Utility 2 Access Code.

3.Press the Add button from the Start menu. The panel announces “Select from Main Menu.”

4.Press Sensor from the Main Menu.

The panel will announce “Press button on sensor X.” X is the next available sensor number. If 24 sensors are already programmed into the panel the panel says “Invalid. Twenty-four sen- sors already programmed.”

5.Trip the sensor.

See Table 8 for descriptions of how to trip each type of sensor. The panel will announce “Press status to accept sensor.” DO NOT press Status at this time. Move on to Step 6.

6.If necessary, change the Sensor name by pressing the Option # button. See Table 8 for Sensor Type Options.

7.Press the Done button to program the sensor.

The system will announce the sensor name, type and number.

Table 8: Programming Sensors

Sensor Type

To Trip

Sensor Type Options

 

 

 

 

 

 

Personal Help Button

Press the help button on the sensor.

Emergency Sensor Type Not Supervised

 

 

Emergency Sensor type Supervised

 

 

 

Pendant Help Button

Press the help button on the sensor.

Emergency Sensor Type Not Supervised

 

 

Emergency Sensor type Supervised

 

 

 

Door/Window Sensor

With the Door/Window Sensor cover

Activity Sensor type Supervised

 

removed, press the Program button on

Activity Sensor type Not Supervised

 

the top of the sensor.

 

 

 

 

Freeze Sensor

With the Freeze Sensor cover

Freeze Sensor type Supervised

 

removed, press the Program button on

 

 

the top of the sensor.

 

 

 

 

Water Sensor

With the Water Sensor cover

Water Sensor type Supervised

 

removed, press the Program button on

 

 

the top of the sensor.

 

 

 

 

Smoke Alarm

Remove the base of the Smoke Alarm

Smoke Sensor type Supervised

 

 

 

Carbon Monoxide (CO)

Plug in the CO Alarm. Within 60 sec-

Carbon Monoxide Sensor type Supervised

Alarm

onds of plugging in, press and hold the

 

 

Test/Reset button until you hear 6

 

 

beeps.

 

 

 

 

Motion Sensor

Remove the sensor from its mounting

Activity Sensor type Supervised

 

plate.

Activity Sensor type Not Supervised

 

 

 

Repeater

With the Repeater cover removed,

Repeater module type Supervised

 

press the tamper switch spring on the

 

 

circuit board.

 

 

 

 

Adding/Replacing Sensors

22

Page 26 Page 28
Image 27
Page 26 Page 28
Contents CareGard FCC Part 15 Information to the User GE InterlogixContents Activity Check Medication RemindersAdding/Replacing Sensors Sensor Testing Phone Communication Testing TroubleshootingDeleting Sensors System Monitoring Special Installation Requirements ETL Listed InstallationsCentral Station Reporting Multi-Purpose Panic Control PanelNo Line Seizure Locating the PanelPlugging in the Phone Line Line SeizureTo activate a portable panic sensor Plugging in the PowerPowering up the System Adjusting the Speaker VolumeUtility Access Code 2 Installer Code Access CodesMaster Access Code Utility Access Code 1 Dealer CodeEntering Program Mode Setting the ClockChanging an Access Code Function Default Range Desired Setting Numbered Options Settings¾ To hear the current setting for each option ¾ To change an option settingRange = On/Off Default = On Option 1 Panel Voice¾ To turn Panel Voice On or Off Option 5 Numeric Pager/Voice Event Notification Phone Option 2 Account NumberOption 3 Primary Phone Number Option 4 Secondary Phone NumberOption 9 Downloader Code Phone Mod 1 SettingsOption 7 Downloader Phone Number Option 8 Phone LockOption 12 Numeric Pager/Voice Event Notification Phone Phone Mod 2 SettingsPhone Mod 3 Settings Option 11 Phone ModOption 14 Auto Phone Test Option 15 RF TimeoutOption 17 AC Power Failure Report Option 13 Dtmf DialingOption 19 Fail to Communicate Option 18 CPU Low Battery ReportRange = On/Off Default = Ring/Hang/Ring SettingsOption 23 300 Baud Option 21 Call Button EnableOption 22 Downloader Enable Option 26 AVM ModeOption 27 RF Jam Detect Option 28 Access Code LengthRange = 3-6 Default = Access Code Length DefaultsOption 33 Modem Sensitivity Option 30 Demo ModeOption 31 Programming Report Option 32 Supervisory TimeOption 37 VOX Receiver Gain Option 38 Alarm Cancel TimeoutOption 39 No Audio on Alarm Cancel Option 36 Manual Mic GainOption 42 Siren Time Out Exiting Programming ModeResetting Memory to Defaults Using CareGard with Activity Check SetSetting up Medication Reminders Home and AwayAcknowledging Medication Reminders Sensor Type To Program Adding Replacing SensorsSupervised vs. Not Supervised Programming SensorsDoor/Window Sensor type possibilities Sensor Type To Trip Sensor Type Options System AC PowerBackup Battery Deleting SensorsSensor Supervisory Failure Sensor Low BatteryReplacing the Backup Battery ¾ To replace the backup batteryCentral Station Communication Sensor TestingAutomatic Phone Test Phone TestPager Reporting Message Pager CommunicationVoice Event Notification Remote Phone OperationRemote Phone Operation System Function Phone CommandProblem Solution Troubleshooting GuideNumerics Index
Top Page Image Contents