Honeywell VISTA-20PSIA, VISTA-15PSIA Configurable Zone Type Fields, Zone Type 90 Report Codes

Page 33

Data Field Programming

Configurable Zone Type Fields

•The system allows you to define custom zone types (VISTA-20P supports 4 [types 90-93]; VISTA-15P supports 2 [types 90, 91]), based on the options described at right.

•All configurable zone types can be programmed via the downloader.

•Configurable zone types 90 and 91 can also be programmed from a keypad using data fields *182-*185.

UL installations: Do not configure zones as fire alarm or UL burglar alarm zones.

*182 Configurable Zone Type 90

0-15 = values for each of 10 entries (0-9, # + 10 = 10,

#+ 11 = 11, # + 12 = 12, # + 13 = 13, # + 14 = 14, # + 15 = 15)

Enter the appropriate value for each entry, 1-10, based on the charts on the next page. To calculate the value for each entry, add the values of the selected options in each of the entry’s columns shown in the respective chart (one option per column). For example, to program entry 2 for “alarm response to short,” “auto restore on,” but not a “vent zone,” enter 5 (“1” for alarm short + “4” for auto restore-yes + “0” for vent zone-no).

*183 Zone Type 90 Report Codes

90 ALARM ID: XXX

TROUBLE ID: XXX

Enter the desired 3-digit Contact ID® report codes for alarms and troubles occurring on zones assigned to this zone type. Use existing Contact ID® codes, if appropriate, or define unique codes in CID code range 750-789. Press [∗] to accept and continue.

Important Notice on Report Codes: To avoid confusion at the central station, it is recommended that existing Contact ID® codes be used with configurable zone types whenever possible. See list in System Communication section and/or check with the central station for a complete list of Contact ID® report codes. If none of the codes are suitable, choose a code in the reserved range of 750-789 and make sure to define the code with your central station.

*184 Configurable Zone Type 91

0-15 = values for each of 10 entries (see field *182 for explanation of entries.)

*185 Zone Type 91 Report Codes

91 ALARM ID: XXX

See field *183 for explanation of

TROUBLE ID: XXX

entries and read the Important

 

notice on using these codes.

Configurable Zone Type Options

Auto Restore (entry 2): Faults on zones set for this option are cleared; restore messages sent upon restoral of faults.

Vent Zone (entry 2): Zones set for this option are ignored if faulted when arming the system, but are protected if the zone is later restored (e.g., an open window can be ignored when arming, but if the window is later closed, it will be protected; opening the window again causes an alarm.)

Bypass Disarmed (entry 4): Zones set for this option can be bypassed only while the system is disarmed.

Bypass Armed (entry 4): Zones set for this option can be bypassed when the system is armed or disarmed.

Dial Delay (entry 6): Alarms on zones set for this option participate in dial delay central station reporting, if system dial delay enabled in field *50.

Fault Delay (entry 6): Faults on zones set for this option are delayed by the time set in field *87. Do not use this option if using entry/exit delay for this zone type.

Faults Display (entry 7): Selects how faults on zones set for this zone type are displayed.

Power Reset/Verification(entry 7): Selects whether the system resets power (when user enters code + OFF), and whether the system performs alarm verification (see description for zone type 16 in Programming Overview section) when a fault occurs on these zones.

Use Entry Delay (entry 8): Selects whether to use the system’s entry delay times.

Use Exit Delay (entry 8): Selects whether to use the system’s exit delay time.

Interior Type (entry 8): Zones set for this option are treated same as standard zone type 4 (bypasses when armed STAY, faults displayed).

Alarm Sounds (entry 9): Selects the type of alarms sound for zones set for this zone type.

Bell Timeout (entry 9): Alarm sounding on zones set for this option remain for the duration set in fields *32 / *33.

Fire Zone (entry 9): Zones set for this option respond in the same manner as if programmed for zone type 9. Do not set fire zones to respond as a “fault” in entries 1-6.

Trouble Sounds (entry 10): Selects the type of trouble sounds for zones set for this zone type (periodic beeps = once every 30 seconds; trouble beeps = rapid beeping).

Chime Enable (entry 10): Zones set for this option cause a chime when Chime mode is on.

4-9

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Ademco Vista Series Recommendations for Proper Protection Table Of Contents Table Of Contents Capabilities and Functions Features and Installation HighlightsImportant Installation Highlights Installer Please Read Compatible DevicesDevice Installing the Control Cabinet and PC Board Mounting and Wiring the ControlAuxiliary Device Current Draw Worksheet Wire Run Chart AC Power, Battery, and Ground ConnectionsSounder Bell Connections Connecting the Keypads and Other Addressable DevicesBasic Connections Supervised outputKeypad Notes Table of Device AddressesLong Range Radio Connections Size MA or less 100 mA 300 mA 500 mA 600 mAHardwire Zones and Zone Expansion Zones Smoke Detector NotesCompatible Receivers Installing the RF Receiver and Wireless Transmitter ZonesRF Receiver No. of Zones Receiver ConnectionsInstalling Installing a 5800TMTransmitter Battery Life ModuleKeyswitch Connections Installing a Keyswitch4204/4229 Relay Modules Powerline Carrier DevicesWith the control as shown below On-Board TriggersPhone Line 4285/4286 Phone Module Phone Module ProblemsBank Audio Alarm Verification Connections AAV, listen-InProgramming Overview About ProgrammingMechanics of Programming Zone Type Definitions Hr Silent Alarm Alarm by NightAlarm Auxiliary AlarmKeyswitch No AlarmConfigurable Response TypeData Field Programming System Setup Fields ∗20 ∗29About Data Field Programming Zone Sounds & Timing ∗31-∗39Dialer Programming ∗40 ∗50 Dynamic Signaling Delay Burglary Dialer DelayDynamic Signaling Priority Zone Programming Menu ModeSystem Status Report Codes Miscellaneous System Fields Program Mode Lockout Options Misc. Fault Delay TimeEvent Log Enables Phone Line Monitor EnablePager Programming Fields Clean Me Option 172Pager Delay Option for AlarmsPager 1 Characters Pager 1 Report OptionsConfigurable Zone Type Configurable Zone Type FieldsConfigurable Zone Type Options Zone Type 90 Report CodesZone Conditions Represented Entries Configurable Zone Type ChartsKeypad Programming Fields Touch Screen Keypad AUI EnableInstallation and Setup Guide Zone Programming Procedure Menu Mode ProgrammingZones and Partitions About Zone Programming ∗56 and ∗58 Menu ModesZone Number Hardwire TypeSummary Screen Zone Type ZTSerial number Entry and Loop Number Entry Input Device typeLoop Number Change Enroll SummaryCompleting Zone Programming ∗58 Expert Programming Mode ProceduresSerial number Zone ProgrammingTo Delete a Serial Number ConfirmTemplate Number Wireless Key Programming TemplatesTemplate Display PartitionWireless Key Transmitter Wireless Key Predefined Default Templates5804BD 2-Way Wireless Key Transmitter Not ConfirmedMenu Mode Output Device Mapping About Output Device Programming *79/*80 Menu ModeProgramming Output Devices Output IdentificationOutput Type Relay PositionModule Addresses Menu Mode Defining Output Functions Output Function NoActivated By 01-08 = zone list ∗ to continue Output Action= off = Change Device State = Close for 2 seconds = Stay ClosedZone List Programming About Zone Lists *81 Menu ModeProgramming Function Keys About Function Keys *57 Menu ModeFunction Key Partition NumbeProgramming Zone Descriptors Menu Mode ∗82 About Descriptor Programming *82 Menu ModeSecond 3-Digit Index No Accept First WordAccept Second Word Assigning Partition/Custom Message DescriptorsFor Entering Zone Descriptors Character Ascii Chart For Adding Custom WordsProgramming Installer and User Schedules Schedule NumberStart Time Repeat Option = repeat every third week 4 = repeat every fourth weekRandomize For events 01 Panel Communication with Central Station System Communication and OperationReport Code Formats DigitCode for Type +1/4+1 Report Standard Expanded WhereAdemco Contact ID Some event codes may not apply to certain control panelsCode Definition System Security Codes Keyfob must be enrolled in system first see Wireless KeyAttributes Values Level User No FunctionsKeypad Functions Keypad CommandsVoice Keypads Function DescriptionKeys Displayed as Zone ∗ /1 ∗ /# Setting the Real-Time ClockAlpha Display Fixed Disp Meaning Various System Trouble DisplaysInstallation and Setup Guide About Test Procedures Testing the SystemChecking Transmitter Enrollment Sniffer Mode System TestAutomatic Standby Battery Tests Go/No Go Test ModeDialer Communication Test and Periodic Test Reports Automatic Periodic Test ReportSecurity Control Specifications & AccessoriesElectrical CommunicationDetector Type Wire Smoke DetectorSeries Transmitter Input Loop Identification Compatible 5800 Series Transmitters TableModel Product Input Type Description 5827 Wireless Keypad Can be used to turn the burglary protection on and offTo be transmitted Industrie Canada Regulatory Agency StatementsUL Notices Page Installation and Setup Guide Page Installation and Setup Guide Limitations of this Alarm System Limitations and Warranty10-8 Index 10-10 Summary of Connections K5305-1V5 10/04 Rev. a Limited Warranty
Top Page Image Contents