Honeywell VISTA-20PSIA, VISTA-15PSIA About Zone Lists *81 Menu Mode, Zone List Programming

Page 48

Installation and Setup Guide

Enter Output No.

R0202

Output Number

01-16 = VISTA-20P output no.; 01-08 = VISTA-15P output no.; 17-18 = on-board triggers Enter the device output number (programmed in *79 Menu Mode) you want associated with this output. Press [✱] to continue.

02A E P TRIG

R02 1 1 3 ZL=00

Summary Screen

A summary screen appears showing the programmed settings. Press [✱] to continue.

About Zone Lists (*81 Menu Mode)

Zone lists let you group individual zones for use with certain system actions. The following table shows the available zone lists and their purposes:

List No.

 

Used for…

Notes

1, 2

general purpose (GP)

• Any list may include any or all of the system's zone

3

 

chime-by-zone(see field *26 to enable option)

numbers.

4

cross zones (see note at right)

• A zone list can be assigned to more than one output relay.

5

night stay zones

• Zone List 4: When creating zone list 4 for cross zoning,

6

 

general purpose

include only zones assigned to zone types 3, 4, or 5. Do not

 

 

V20PSIA/V15PSIA

: dial delay disable

include zones that have delays (entry/exit zones, interior

7

 

general purpose

w/delay) or 24-hour zones, as these zone types may produce

 

 

V20PSIA/V15PSIA

: unlimited reports

unpredictable operation and may not function as intended.

8

 

general purpose

See field *85 for Cross Zone Timer option.

9

zones that activate Pager 1

• Zone List 6:

V20PSIA/V15PSIA

: See field *50 for Dial Delay

10

zones that activate Pager 2

Disable option.

11

zones that activate Pager 3 (VISTA-20P)

• Zone List 7:

V20PSIA/V15PSIA

: See field *93 for Unlimited

12

zones that activate Pager 4 (VISTA-20P)

Reports option.

Zone List Programming

1.Select an appropriate zone list number.

2.Add the desired zone numbers to be included in that list.

Start Zone List Program Mode by pressing ✱81 while in Data Programming mode.

*81 Menu Mode

 

 

 

Zone List Number

 

Zone List No.

 

 

 

01-12 = zone list number; [∗] to continue

 

(00 = Quit)

01

 

Enter the Zone List Number to program (or 00 to quit). Press [✱] to advance.

 

 

 

 

 

 

In the following displays, zone list 01 has been selected for programming.

 

 

 

Zone Number

 

01 Enter Zn Num.

 

01-64†= zone numbers followed by [∗] to accept each zone; 00 to continue

 

(00 = Quit)

00

 

Enter each zone number to add to the zone list, followed by pressing [✱] (example, 01✱,

 

 

 

 

 

 

 

 

 

02✱, 03✱). After all zones are entered, press 00 to continue.

 

 

 

IMPORTANT: Do not include fire zones in zone lists that are used to STOP device actions.

 

 

 

† VISTA-20P = 01-64; VISTA-15P = 01-06, 09-34, 49-56.

01 Del Zn List?

Deleting Zone Lists

0 = don’t delete list; 1 = delete this zone list; [∗] to continue

0 = No 1 = Yes 0

To delete the zone list, enter 1. All zones in the zone list will be deleted automatically and

 

the system returns to the Zone List No. prompt. To save the zone list, enter 0.

01 Delete Zone?

0 = No 1 = Yes 0

Deleting a Zone

0 = don’t delete zones; 1 = go to next prompt to delete zones; [∗] to continue

To save the zone list, enter 0 and the system returns to the Zone List No. prompt. To delete a zone or zones in a zone list, enter 1 to continue.

01 Zn to Delete?

 

(00 = Quit)

00

Delete the Zone

01-64†= zones to be deleted from list followed by [∗] to accept each zone; 00 to continue Enter each zone to be deleted from the list, followed by [✱]. After all zones to be deleted are entered, enter 00 to return to the Zone List No. prompt so that another list can be programmed, if desired.

† VISTA-20P = 01-64; VISTA-15P = 01-06, 09-34, 49-56.

5-12

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Ademco Vista Series Recommendations for Proper Protection Table Of Contents Table Of Contents Features and Installation Highlights Capabilities and FunctionsImportant Installation Highlights Installer Please Read Compatible DevicesDevice Mounting and Wiring the Control Installing the Control Cabinet and PC BoardAuxiliary Device Current Draw Worksheet AC Power, Battery, and Ground Connections Wire Run ChartConnecting the Keypads and Other Addressable Devices Sounder Bell ConnectionsBasic Connections Supervised outputTable of Device Addresses Keypad NotesLong Range Radio Connections Size MA or less 100 mA 300 mA 500 mA 600 mAHardwire Zones and Zone Expansion Smoke Detector Notes ZonesInstalling the RF Receiver and Wireless Transmitter Zones Compatible ReceiversRF Receiver No. of Zones Receiver ConnectionsInstalling a 5800TM InstallingTransmitter Battery Life ModuleInstalling a Keyswitch Keyswitch ConnectionsPowerline Carrier Devices 4204/4229 Relay ModulesOn-Board Triggers With the control as shown belowPhone Module Problems Phone Line 4285/4286 Phone ModuleAudio Alarm Verification Connections AAV, listen-In BankProgramming Overview About ProgrammingMechanics of Programming Zone Type Definitions Alarm by Night Hr Silent AlarmAlarm Auxiliary AlarmNo Alarm KeyswitchConfigurable Response TypeSystem Setup Fields ∗20 ∗29 Data Field ProgrammingAbout Data Field Programming Zone Sounds & Timing ∗31-∗39Dialer Programming ∗40 ∗50 Burglary Dialer Delay Dynamic Signaling DelayDynamic Signaling Priority Zone Programming Menu ModeSystem Status Report Codes Miscellaneous System Fields Misc. Fault Delay Time Program Mode Lockout OptionsEvent Log Enables Phone Line Monitor EnablePager Programming Fields 172Pager Delay Option for Alarms Clean Me OptionPager 1 Characters Pager 1 Report OptionsConfigurable Zone Type Fields Configurable Zone TypeConfigurable Zone Type Options Zone Type 90 Report CodesConfigurable Zone Type Charts Zone Conditions Represented EntriesTouch Screen Keypad AUI Enable Keypad Programming FieldsInstallation and Setup Guide Menu Mode Programming Zone Programming ProcedureZones and Partitions About Zone Programming ∗56 and ∗58 Menu ModesHardwire Type Zone NumberSummary Screen Zone Type ZTInput Device type Serial number Entry and Loop Number EntryLoop Number Change Enroll Summary∗58 Expert Programming Mode Procedures Completing Zone ProgrammingZone Programming Serial numberTo Delete a Serial Number ConfirmWireless Key Programming Templates Template NumberTemplate Display PartitionWireless Key Predefined Default Templates Wireless Key Transmitter5804BD 2-Way Wireless Key Transmitter Not ConfirmedAbout Output Device Programming *79/*80 Menu Mode Menu Mode Output Device MappingProgramming Output Devices Output IdentificationOutput Type Relay PositionModule Addresses Menu Mode Defining Output Functions Output Function NoActivated By Output Action 01-08 = zone list ∗ to continue= off = Change Device State = Close for 2 seconds = Stay ClosedAbout Zone Lists *81 Menu Mode Zone List ProgrammingAbout Function Keys *57 Menu Mode Programming Function KeysFunction Key Partition NumbeAbout Descriptor Programming *82 Menu Mode Programming Zone Descriptors Menu Mode ∗82Accept First Word Second 3-Digit Index NoAccept Second Word Assigning Partition/Custom Message DescriptorsCharacter Ascii Chart For Adding Custom Words For Entering Zone DescriptorsProgramming Installer and User Schedules Schedule NumberStart Time Repeat Option = repeat every third week 4 = repeat every fourth weekRandomize For events 01 System Communication and Operation Panel Communication with Central StationReport Code Formats DigitWhere Code for Type +1/4+1 Report Standard ExpandedAdemco Contact ID Some event codes may not apply to certain control panelsCode Definition Keyfob must be enrolled in system first see Wireless Key System Security CodesAttributes Values Level User No FunctionsKeypad Commands Keypad FunctionsVoice Keypads Function DescriptionSetting the Real-Time Clock Keys Displayed as Zone ∗ /1 ∗ /#Various System Trouble Displays Alpha Display Fixed Disp MeaningInstallation and Setup Guide Testing the System About Test ProceduresChecking Transmitter Enrollment Sniffer Mode System TestGo/No Go Test Mode Automatic Standby Battery TestsDialer Communication Test and Periodic Test Reports Automatic Periodic Test ReportSpecifications & Accessories Security ControlElectrical CommunicationWire Smoke Detector Detector TypeSeries Transmitter Input Loop Identification Compatible 5800 Series Transmitters TableModel Product Input Type Description 5827 Wireless Keypad Can be used to turn the burglary protection on and offTo be transmitted Regulatory Agency Statements Industrie CanadaUL Notices Page Installation and Setup Guide Page Installation and Setup Guide Limitations and Warranty Limitations of this Alarm System10-8 Index 10-10 Summary of Connections Limited Warranty K5305-1V5 10/04 Rev. a
Top Page Image Contents