Honeywell VISTA-15P, VISTA-20P Output Action, 01-08 = zone list ∗ to continue, = Stay Closed

Menu Mode Programming

“A”

01 Zn List

1

Zone List (prompt appears if zone list was selected)

01-08 = zone list; [∗] to continue

Enter the desired zone list number associated with this output number. NOTE: Do not use pager zone lists 09-12 in output definitions.

Enter the zone list event that will activate this output.

Enter Event		0	= restore; 1 = alarm;
Alarm	1	2	= fault; 3= trouble

NOTE: For alarm, fault, and trouble, an event on ANY zone in the list activates the output, but ALL zones in the list must be restored before the output is restored.

Press [✱] to continue and skip to the “Output Action” prompt.

“B”

01 Enter Zn type

Perimeter 03

“C”

01 Enter Zn No.

12

Zone Type (prompt appears if zone type was selected)

Enter the desired zone type associated with this output number. See below for a list of available zone types.

CHOICES FOR ZONE TYPES:

00	= Not Used	05	= Day/Night		12	= Monitor Zone
01	= Ent/Exit #1	06	= 24 Hr Silent		14	= Carbon Monoxide
02	= Ent/Exit #2	07	= 24 Hr Audible		16	= Fire w/verification
03	= Perimeter	08	= 24 Hr Aux		23	= No Alarm Response
04	= Interior Follower	09	= Fire		24	= Silent Burglary
		10	= Interior w/Delay		77	= Keyswitch Zone
					81	= AAV Monitor Zone
					90-91 = Configurable
CHOICES FOR SYSTEM OPERATION:
20	= Arming–Stay	36		= **At Bell Timeout***		52	= Kissoff
21	= Arming–Away	38		= Chime		54	= Fire Zone Reset
22	= Disarming	39		= Any Fire Alarm		58	= Duress
31	= End of Exit Time	40		= Bypassing		60	= AAV
32	= Start of Entry Time	41		= **AC Power Failure		66	= Function Key†
33	= Any Burglary Alarm 42 = **System Battery Low 67 = Bell Fail
		43		= Comm. Failure		68	= Telco Line Cut
						78	= Keyswitch Red LED
						79	= Keyswitch Green LED

**Use 0 (Any) for Partition No. (P) entry.

***Or at Disarming, whichever occurs earlier.

† Use *57 Menu Mode to assign the function key (function “07”).

Note: In normal operation mode:

Code + # + 7 + NN Key Entry starts Device NN.

Code + # + 8 + NN Key Entry stops Device NN.

Enter the partition in which this zone type will occur.

01 Partition		0 = any partition; 1 = partition 1;
Any partition	0	2 = partition 2; 3 = common

Press [✱] to continue and skip to the “Output Action” prompt.

Zone Number (prompt appears if zone number was selected) Enter the desired zone number associated with this output number. Press [✱] to continue.

Enter the zone event that will activate this output.

01 Enter Event

Restore0

0 = restore; 1 = alarm/fault/trouble

Press [✱] to continue to the “Output Action” prompt

01 Output Action
Close for 2 sec	1

Output Action

0	= off	4	= Change Device State
1	= Close for 2 seconds	5	= Duration 1 (see data field *177)
2	= Stay Closed	6	= Duration 2 (see data field *177)

3 = Pulse on & off (1 sec ON, 1 sec OFF)

Enter the desired device action as listed above. Press the [✱] key to continue.

5-11