Honeywell LYNXR-I manual Event Identifier Entries, Entry Event Comment

Page 34

USER FUNCTIONS

Scheduling User Interface

Event Identifier Entries

Note: On systems that are is equipped with a Wireless keypad, reminder announcements and the alarm clock will only be broadcast locally by the LYNXR keypad.

Entry	Event	Comment
0	Empty	No event scheduled (or schedule is temporarily disabled)

1	X10 Device	Turn an X10 device, either on or off at begin/end times. (will
		have a start and end time to program) (time driven)
		NOTE: SH10A siren cannot be used.

2	Latch Key Report	Send a special pager report (7110000) indicating system not
		yet disarmed. (will have a start/end time to send the report)
		(window driven), (reports only to pager)
		NOTE: Option *49 must be programmed to be 6 or higher.
		Make sure unit is armed prior to start of window time.
		In addition a secondary phone number must be
		programmed in Option *42.

3	Automatic Stay Arming	Will arm the system automatically, and bypass any open
		zones, at a given time. It will send a report to the pager and
		central station, indicating system has been auto armed stay,
		plus all bypass reports. (will have only a start time to send the
		report) (time driven)
		NOTES: (1) Prior executing auto stay arming, force bypass
		will be executed - if option *23 was enabled.
		(2) If pager report is required, Option *49 must be
		programmed to be 6 or higher.

4	Reminder Announcements	Will announce the message recorded by your installer. This
		will be repeated every minute until a key is depressed, or a
		button type zone does an arm or disarm. †
		NOTE: Make sure installer programmed the message at the
		time of installation.

5	Alarm Clock	Will start a trouble tone (beep) on the speaker, which will
		continue until a key is depressed. †

Figure 1.

– 34 –

Image 34

Contents Ademco LYNXR-I Page Table of Contents Page System Overview AUX Fire Protection AlarmsZones Burglary ProtectionTwo-Way Voice Feature General OperationTo arm in Away mode To arm in Stay modeTo restart exit delay To arm with no DelayTo remotely activate X10 devices To turn Test mode onTo turn Test mode off To remotely activate X10 devices 7About the Master Keypad GeneralMaster Keypad Definitions Armed ReadySystem Overview About the Display and Indicators LED MeaningsPress the Status Key Checking System StatusGeneral Information System Can Be ArmedRestarting Exit Delay While System Armed Arming in Stay ModeArming In Away Mode Arming the SystemTo arm with no Delay if Quick Arm is active Arming the System With No DelayQuick Arming Entry Delay Entry/Exit DelaysExit Delay Exit Alarms Exit Alarm ActiveTo disarm the system and silence burglary alarms Memory of AlarmDisarming the System Forced Bypass Bypassing Protection ZonesBypassing Individual Zones Displaying Bypassed ZonesChime Mode Panic Keys / Chime ModePanic Keys Code Format Paging FeatureAutomatic Paging Manual PagingSystem Announcements Follow Me Announcement FeatureFollow Me Reminder and System Announcements Reminder AnnouncementsTo program Follow Me reminder telephone number To delete Follow Me reminder telephone numberTo deactivate X10 devices 7 Device DescriptionsDevice Description Message Playback Message Recording/Playback/Volume ControlRecording a Message Deleting MessagesTo adjust message playback/system announcement volume Adjusting the VolumeTo restore announcement sounding Defining the AUX Function AUX FunctionPerforming the AUX function Minute Clock/CalendarHour MonthDay YearScheduling User Interface = the value that was last stored in the memory Schedule numberXx bd Event Identifier Entries Entry Event CommentDay of Week Entries Entry DayUsing Remote Phone Control Feature Remote Phone Control FeatureEnter To remotely deactivate X10 devices 1-6 # + 7 + device no Remote Phone Control Commands To remotely disarm systemTo remotely arm in Away mode To remotely Bypass zonesSpeaker Phone Feature Using the Speaker Phone FeatureUser Functions General Information Silencing a Fire AlarmCase of Fire Fire Alarm System Emergency Evacuation Changing the Master User Code Security CodesTo Add/Delete a User or Change a Users Code Add a user codeEntering Test Mode Testing the System to be conducted weeklyExit Test Mode Typical Trouble Condition Displays Trouble MessagesRoutine Care Changing the LYNXR-I System Battery Low Battery Conditions in Wireless SensorsMaintaining your system Summary Of Audible Notification LED Meanings Federal Communications Commission FCC Part 15 Statement UL Notice This is a Grade a residential systemIndustry Canada Federal Communications Commission FCC Part Ringer Equivalence Number NoticeEvent of Telephone Operational Problems Servicing Information Owners Insurance Premium Credit Request Notifies Insert B = Burglary, F = FireOwners Insurance Premium Credit Request Index Manual Paging Limitations of this Alarm System ONE Year Limited Warranty Page Page Page Page Page ‡K14115$Š