Honeywell LYNXR-I manual Zones, Fire Protection, Burglary Protection, Security Codes, Alarms

Page 7

SYSTEM OVERVIEW

General Operation

Zones

Your system's sensing devices have been assigned to various "zones." For example, the sensing device on your entry/exit door may have been assigned to zone 01, sensing devices on windows in the master bedroom to zone 02, and so on. These numbers appear on the display when an alarm or trouble condition occurs.

UL

LYNXR-I is not intended for UL985 Household Fire applications unless a 24-hour

backup battery (P/N LYNXRCHKIT-HC) is installed.

 

 

 

Fire Protection

The fire protection portion of your security system (if used) is always active and will sound an alarm if a fire condition is detected. Refer to the FIRE ALARM SYSTEM section for important information concerning fire protection, smoke detectors and planning emergency exit routes from the premises.

Burglary Protection

Your system provides two modes of burglary protection: STAY and AWAY. STAY mode protects the perimeter only, allowing you to freely move within inside the premises. AWAY mode protects the entire system. Both modes provide an entry delay time that allows you to reenter the premises without setting off an alarm. For additional security, you can turn the entry delay off when arming the system by using

the

NO DELAY

key in combination with the desired arming key. The system also allows you to bypass

selected zones before arming the system, if desired. Refer to the BYPASSING PROTECTION ZONES section. The system also provides a CHIME mode, for alerting users to the opening of protected doors and windows while the system is disarmed.

You must turn on ("arm") the burglary protection portion of your system before it will sense burglary alarms. To arm the system, enter your user code then press the desired arming key (AWAY or STAY). Refer to the ARMING THE SYSTEM section for detailed procedures and information.

Security Codes

At the time of installation, you were assigned a personal 4-digit security or “master user” code. You must enter the user code when arming and disarming the system, and when performing other system functions. As an additional security feature, other users who do not need to know your code can be assigned up to 6 different security codes. Refer to the SECURITY CODES section for procedures on adding security codes to the system.

Alarms

When an alarm occurs, the keypad and external sounders will sound for about 15-seconds, and the keypad will display the zone(s) causing the alarm. After 15-seconds, the siren stops temporarily and voice announcements of the zones in alarm begins. When these zones have been announced, the siren sounds again and the cycle repeats itself, until the system is disarmed (code + OFF) or until alarm bell

– 7 –

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Ademco LYNXR-I Page Table of Contents Page System Overview AUX Burglary Protection AlarmsZones Fire ProtectionGeneral Operation Two-Way Voice FeatureTo arm with no Delay To arm in Stay modeTo restart exit delay To arm in Away modeTo remotely activate X10 devices 7 To turn Test mode onTo turn Test mode off To remotely activate X10 devicesGeneral About the Master KeypadArmed Ready Master Keypad DefinitionsSystem Overview LED Meanings About the Display and IndicatorsSystem Can Be Armed Checking System StatusGeneral Information Press the Status KeyArming the System Arming in Stay ModeArming In Away Mode Restarting Exit Delay While System ArmedTo arm with no Delay if Quick Arm is active Arming the System With No DelayQuick Arming Exit Alarms Exit Alarm Active Entry/Exit DelaysExit Delay Entry DelayTo disarm the system and silence burglary alarms Memory of AlarmDisarming the System Displaying Bypassed Zones Bypassing Protection ZonesBypassing Individual Zones Forced BypassChime Mode Panic Keys / Chime ModePanic Keys Manual Paging Paging FeatureAutomatic Paging Code FormatReminder Announcements Follow Me Announcement FeatureFollow Me Reminder and System Announcements System AnnouncementsTo delete Follow Me reminder telephone number To program Follow Me reminder telephone numberTo deactivate X10 devices 7 Device DescriptionsDevice Description Deleting Messages Message Recording/Playback/Volume ControlRecording a Message Message PlaybackTo adjust message playback/system announcement volume Adjusting the VolumeTo restore announcement sounding Defining the AUX Function AUX FunctionPerforming the AUX function Month Clock/CalendarHour MinuteYear DayScheduling User Interface Schedule number = the value that was last stored in the memoryXx bd Entry Event Comment Event Identifier EntriesEntry Day Day of Week EntriesUsing Remote Phone Control Feature Remote Phone Control FeatureEnter To remotely Bypass zones Remote Phone Control Commands To remotely disarm systemTo remotely arm in Away mode To remotely deactivate X10 devices 1-6 # + 7 + device noUsing the Speaker Phone Feature Speaker Phone FeatureUser Functions General Information Silencing a Fire AlarmCase of Fire Fire Alarm System Emergency Evacuation Add a user code Security CodesTo Add/Delete a User or Change a Users Code Changing the Master User CodeEntering Test Mode Testing the System to be conducted weeklyExit Test Mode Typical Trouble Condition Displays Trouble MessagesRoutine Care Changing the LYNXR-I System Battery Low Battery Conditions in Wireless SensorsMaintaining your system Summary Of Audible Notification LED Meanings Federal Communications Commission FCC Part 15 Statement UL Notice This is a Grade a residential systemIndustry Canada Ringer Equivalence Number Notice Federal Communications Commission FCC PartEvent of Telephone Operational Problems Servicing Information Notifies Insert B = Burglary, F = Fire Owners Insurance Premium Credit RequestOwners Insurance Premium Credit Request Index Manual Paging Limitations of this Alarm System ONE Year Limited Warranty Page Page Page Page Page ‡K14115$Š
Top Page Image Contents