Whirlpool 1187361 Mode, Fan Speed, Temperature, To change the temperature display from F to C

Page 11

Mode

1.Press MODE until you see the indicator light come on for the setting you desire.

2.Choose AUTO, COOL, FAN ONLY or POWER SAVER.

■Auto - Cools room while it automatically controls fan speed. You cannot change fan speed, but you can adjust temperature by pressing the plus or minus button.

■Cool - Cools room. You can select fan speed by pressing Fan Speed. You can then adjust temperature by pressing the plus or minus button.

■Fan Only - Only the fan runs. Display shows “FO” (fan only).

NOTE: Fan runs on Turbo speed only.

■Power Saver - Fan runs only when cooling is needed. Fan stops running when the room temperature matches the Temperature control setting.

Since the fan does not circulate the room air continuously, less energy is used, but the room air is not circulated as often. Use Power Saver when you are asleep or away from home.

Fan Speed

NOTE: The Fan Speed button will operate only when Cool or Power Saver mode has been selected.

1.Press FAN SPEED until you see the indicator light come on for the setting you desire.

2.Choose TURBO, HIGH or LOW.

Temperature

■Press the plus button to raise the temperature. Each time you press or hold the plus button, the temperature will go up

1º until it reaches 86°F (30°C).

■Press the minus button to lower the temperature. Each time you press or hold the minus button, the temperature will go down 1º until it reaches 64°F (18°C).

To change the temperature display from °F to °C:

1.Turn off the air conditioner.

2.While the air conditioner is off, press and hold down the MODE and FAN SPEED buttons while pressing POWER to turn the air conditioner on.

NOTE: Follow these same steps to change the temperature display from °C to °F.

Timer delay

To set the Timer for a 1- to 24-hour delay until the air conditioner turns off (the air conditioner must be On):

1.Press TIMER. Indicator light will flash.

2.Press the plus or minus button to adjust the delay time (1 to 24 hours).

3.Press TIMER again or wait 10 seconds. Indicator light will remain on.

To set the Timer to turn on the air conditioner, keeping previous settings:

1.Turn off air conditioner.

2.Press TIMER. Indicator light will flash.

3.Press the plus or minus button to change delay time (1 to 24 hours).

4.Press TIMER again or wait 10 seconds. Indicator light will remain on.

To set the Timer to turn on the air conditioner, changing the previous settings:

1.Turn air conditioner on.

2.Adjust MODE to Auto, Cool, Fan Only, or Power Saver.

3.Adjust FAN SPEED to Turbo, High or Low.

4.Adjust temperature between 64°F (18ºC) and 86°F (30ºC).

5.Wait 3 seconds before turning off air conditioner.

6.Press TIMER. Indicator light will flash.

7.Press the plus or minus button to change delay time (1 to 24 hours).

8.Press TIMER again or wait 10 seconds. Indicator light will remain on.

To clear Timer delay program:

NOTE: Air conditioner can be either on or off.

Press and hold TIMER for 3 seconds. Indicator light will shut off.

To see the remaining time (in hours):

1.Press TIMER once after it has been programmed.

2.While the display is showing the remaining time, you can press the plus or minus button to increase or decrease the time.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Manual de Uso y Cuidado AIR ConditionerAcondicionador DE Aire Use & Care GuideÍndice AIR Conditioner SafetyTools needed Installation RequirementsTools and Parts Location RequirementsRecommended ground method Window installationPower supply cord Wiring requirements Plug outlet Electrical RequirementsUnpack the Air Conditioner Installation InstructionsSMART-MOUNTTray Installation Thick wall construction brick Attach support legsThin wall construction vinyl, wood, etc Install side curtains Prepare Air Conditioner for InstallationInstall in window Top view Bottom view Position the Air ConditionerFront view Correct installationIncorrect installation Attach side curtains to windowStarting Your Air Conditioner Digital Control Complete InstallationAIR Conditioner USE To clear Timer delay program TemperatureTo change the temperature display from F to C Timer delayTo raise the temperature To operate air conditioner with remote controlTo select the mode To select the fan speed in Cool or Power Saver mode onlyExhaust Control on some models Models without Power Saver Models with Power SaverStarting Your Air Conditioner Rotary Control Changing Air Direction Cleaning the Air FilterCleaning the Front Panel Annual MaintenanceTroubleshooting U.S.A Assistance or ServiceAccessories Piezas suministradas Seguridad DEL Acondicionador DE AireRequisitos DE Instalación Herramientas y piezasInstalación del ensamblaje de la bandeja Smart Requisitos eléctricos Requisitos para la ubicaciónInstalación en la ventana Instalación de la bandeja Instrucciones DE InstalaciónDesempaque el acondicionador De aire Construcción gruesa de la pared ladrillos Fije las patas de soporteConstrucción delgada de la pared vinilo, madera, etc Instálela en la ventana Prepare el acondicionador de aire Para la instalaciónVista inferior Instalación de las cortinas lateralesInstalación incorrecta Colocación del acondicionador De aireInstalación correcta Vista superior Complete la instalaciónFije las cortinas laterales a la ventana Vista frontalFan Speed Velocidad de ventilación Mode ModoCómo Usar SU Acondicionador DE Aire Para ver el tiempo restante en horas TemperaturaPara cambiar la pantalla de la temperatura de C a F Para bajar la temperatura Para encender o apagar el acondicionador de airePara seleccionar el modo Para subir la temperaturaModelos sin ahorro de energía Modelos con ahorro de energía Control de respiradero en algunos modelosLimpieza del panel delantero Cómo cambiar la dirección del aireSonidos normales Limpieza del filtro de aireParece que el acondicionador de aire funciona excesivamente Solución DE ProblemasSu acondicionador de aire no funcionará Accesorios Ayuda O Servicio TécnicoEn los EE.UU 1187361
Top Page Image Contents