New Buck Corporation Heater Model 80 manual Possible Tools Needed For Installation, Fireplace

Page 10

POSSIBLE TOOLS NEEDED FOR INSTALLATION

If you decide to install your own stove, there are several hand tools you may need to do the job. If you do not already have them, they are readily available at most hardware stores.

Caulking gun

Large adjustable wrench (may not be needed) Drop cloths or newspapers

Vacuum cleaner or whisk broom Flashlight

1 tube of RTV silicone, Code 103 or 106, or high temperature rubber cement rated between 450o F- 600o F. 7/32" drill bit and drill

Socket/Rachet Set

Insulation (Provided in trim kit package)

INSTALLATION PREPARATION

Fireplace

1.Locate furniture and other materials away from the front of the fireplace to allow free access to the fireplace.

2.Cover the hearth and adjacent floor areas with the drop cloths to protect from soiling or scarring the surface.

3.Remove the existing fireplace damper plate.

4.Thoroughly clean the fireplace of ashes and soot.

5.Check the chimney and smoke chamber for excessive buildup of creosote or soot. Also, check for obstructions, such as birds’ nest. If the chimney is excessively dirty, clean it, or have someone clean it professionally BEFORE installing the room heater.

6.If the fireplace has an ash dump or outside air provision, these must be sealed off with metal or tightly packed non-combustible insulation to prevent cold air from entering the fireplace chamber.

Heater Preparation

1.Inspect the unit for any obvious physical damage.

2.Check the primary air draft controls to ensure that they slide freely.

3.Check the operation of the damper control to ensure that it will open and close properly.

It is not necessary to direct connect this unit unless installed in an improper drawing fireplace or oversized flue.

POSITIONING THE HEATER

When positioning the heater, the following conditions MUST be met! (See Figure 2)

1.The front of the damper opening must be BEHIND the rear edge of the lintel to ensure proper draft. (See Figure 2)

2.The vertical plane of the fireplace front must fall BEHIND the side panels of the unit. (In other words, it is possible to have the heater too far in as well as not far enough.)

3.Center the heater in the fireplace opening.

8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents SAFETY NOTICE FEATURES PREPARATION INSTALLATIONOPERATION MAINTENANCE SAFETY “MEETS PHASE II EPA STANDARDS”Page SECTION TABLE OF CONTENTSSECTION SECTIONPage ROOM HEATER FEATURES SECTIONModel 80 Wood Stove CATALYST EQUIPPED CATALYST WARRANTYEPA COMPLIANCE STATUS PROPER FUEL SELECTIONCAUTION AGAINST OVER-FIRING ACHIEVING CATALYTIC LIGHT-OFFWHEN REFUELINGCATALYST MONITORING ASH REMOVALREQUIRED FIREPLACE DIMENSIONS MASONRY INSERT INSTALLATIONINSTALLATIONS Fireplace Insert INSTALLATION PRECAUTIONSPOSITIONING THE HEATER POSSIBLE TOOLS NEEDED FOR INSTALLATIONINSTALLATION PREPARATION FireplaceMOUNTING THE TRIM PANELS FINAL CHECK INSTALLATION PRECAUTION RESIDENTIAL FREESTANDING ROOM HEATER INSTALLATIONSECTION FLOOR PROTECTION TOOLS FOR INSTALLATIONMODEL Minimum Clearances CHIMNEY Preparing The Stove for InstallationDETERMINING THE CHIMNEY LOCATION Wall Exit Into Masonry using single wall pipe Wall Exit Into Metal Tee-BoxCeiling Exit-CloseClearance Tested and Listed Wall Protector ALTERNATIVES FOR WALL PROTECTIONFINAL CHECK Unlisted and Untested Wall Protector3.Open the primary air drafts and damper bypass WOOD HEATER SAFETY SECTIONOPERATION GUIDE TO THE DIFFERENT BURNING QUALITIES OF WOODSECTION Building a Fire PREVENTIVE MAINTENANCE / PARTS REPLACEMENT Disassembly Inspection and Catalytic ReplacementGASKET REPLACEMENT Cold Heater SECTIONPage Solution TROUBLESHOOTINGProblem SECTIONCOMBUSTOR-RELATEDPROBLEMS ProblemSolution Possible CauseNEW BUCK CORPORATION NBC
Top Page Image Contents