New Buck Corporation 34 manual Ceiling

Page 28

SECTION III

INSTALLATION MODEL 34 (FP)

IN SOLID FUEL BURNING FIREPLACES

(1)The Model FP-34 may be installed in a masonry fireplace. The minimum fireplace dimension must be 24" high, 29-1/2" wide, and 12" deep.

(2)For minimum dimensions for the sidewall and mantel, see Figure 6.

(3)Center the heater in fireplace opening.

(4)NOTE: See “Producing Adequate Ventilation” page 35.

NOTE: The installer of this appliance must mechanically (peel and stick) attach the marking supplied with this unvented appliance before installing to the inside of the firebox of the solid- fuel burning fireplace or listed ventless firebox enclosure into which the unvented fireplace insert is installed. See the example of the marking on page 10 of this manual.

CAUTION: Cutting any sheet-metal parts of the solid-fuel burning fireplace or listed ventless enclosure in which the unvented fireplace is to be installed is prohibited.

NOTE: “If the factory-built fireplace has no gas access hole(s) provided, an access hole of 1.5 inch (37.5) diameter or less may be drilled through the lower sides or bottom of the firebox in a proper workmanlike manner. This access hole must be plugged with non-combustible insulation after the gas supply line has been installed.”

“Refractory, glass doors, screen rails, screen mesh and solid-fuel log grates (if applicable) can be removed from the fireplace before installing the unvented fireplace insert.”

NOTE: After the unit is positioned in fireplace, mark the trim panels as follows:

A.Set the side panels in place, flat against the fireplace. Mark down the inside edge of the trim panel to make a vertical reference line.

 

CEILING

 

 

 

24"

 

20"

 

7"

7"

 

LEFT

RIGHT

Figure 6

SIDE

SIDE

 

26

 

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Model Page Table of Contents Model Page Section I Safety Information Warnings Page Page Section Fireplace PreparationInstallation and Clearances GAS ConnectionPage Millivolt only GAS Pressure Check Millivolt SIT MANUAL-MODULATINGWhat to do if YOU Smell GAS Rocker Switch ITT Valve To Turn OFF GAS to Appliance Shutting OFF UnitManual Lighting Procedure Thermostat Control OperationFor Your Safety Read Before Lighting Lighting Instruction Modulating Valve SIT Manual Valve SITLighting Instruction Page Thermostat Control Operation Operating Instructions Page Page Manual Lighting Procedure When Used AS a Heating Appliance Heat Output Flame CheckCR3329 LOG SET B. LOG SETWiring Diagram Room Blower Installation and Operation Instructions Ceiling Page Page Page Section V Model 34 ZC Zero Clearance Installation Choosing the Location for Your FireplaceGAS Line DraftsGAS Line Installing the Firebox ZC Fireplace Clearances ZCFinishing Your Fireplace ZC Clearances ZCSection After Market Mobile Home Installation Determining FRESH-AIR Flow for Heater Location Producing Adequate VentilationDetermine if YOU have a Confined or Unconfined Space Determine the volume of the space length x width x height Ventilation AIR Ventilation AIR from Inside BuildingVentilation AIR from Outdoors Important Safeguards CleaningObserved Possible Problem Cause SolutionObserved Possible Problem Solution Observed Possible Problem Cause Solution Observed Possible Problem Cause Solution Repair Parts ServicingReplacement Parts OFF PE RV20LF90 PE RV20LF35PO 382BINIP PO 385BINIPTSi Replacement Parts S Pilot NAT. O.P. AssemblyMF 31621ALMTUB Orifice PO Orifice Orifice Holder PO 54ORFHLD NUT & SleeveSIT Millivolt Replacement Parts for Ember Stove Base ESB ESB Limited Warranty VENT-FREE GAS LOG Heater Warranty does not Cover
Top Page Image Contents