Heat & Glo LifeStyle SL-750TV-IPI-E Framing and Clearances, Selecting Appliance Location

Page 19

5 Framing and Clearances

A. Selecting Appliance Location

When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1).

WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.

Due to high temperatures, the appliance should be locat- ed out of trafﬁc and away from furniture and draperies.

NOTICE: Illustrations reﬂect typical installations and are FOR DESIGN PURPOSES ONLY. Illustrations/diagrams are not drawn to scale. Actual installation may vary due to individual design preference.

F A

A

TOP VENT

B

ALCOVE D INSTALLATION

B

C

TOP VENT

TOP VENT

B

E

	Model		A	B	C	D	E	F
	Model		A	B	C	D	E	Minimum
								Minimum
	SL-550TV-IPI-E	Inches	42	37	59-1/2		16-1/4	1/2

		Millimeters	1067	940	1511		413	13
		Millimeters	1067	940	1511		413	13

		Inches	45-1/2	42	64-3/8	See Section	16-1/4	1/2
	SL-750TV-IPI-E					5.D for Alcove
	SL-750TV-IPI-E					5.D for Alcove
		Millimeters	1156	1067	1635	Installation	413	13

	SL-950TV-IPI-E	Inches	50-1/2	49	71-1/2		16-1/4	1/2

		Millimeters	1283	1245	1816		413	13
		Millimeters	1283	1245	1816		413	13

Figure 5.1 Appliance Locations

Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. J • 12/09

19

Image 19

Contents What to do if you smell gas SL-550TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-EHomeowner Reference Information CongratulationsUser Guide Table of ContentsTroubleshooting Appliance SetupReference Materials Limited Lifetime Warranty Limited Lifetime Warranty BTU Speciﬁcations Listing and Code ApprovalsAppliance Certiﬁcation Tempered Glass SpeciﬁcationsElectrical Codes High Altitude InstallationsNon-Combustible Materials Speciﬁcation Combustible Materials SpeciﬁcationOperating Instructions User Guide Gas Fireplace SafetyYour Fireplace Decorative Doors and Fronts Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Fan Kit optionalFinal inspection by Lighting Instructions IPIAfter Fireplace is Lit Frequently Asked QuestionsRemote Control Maintenance and ServiceMaintenance Tasks-Homeowner Glass CleaningLogs Maintenance Tasks-Qualiﬁed Service TechnicianGasket Seal and Glass Assembly Inspection VentingEither cobrahead or SIT Typical Appliance System Getting StartedTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Negative Pressure Selecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseCombustible Mantels Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsVent Guidelines Vent Information and DiagramsVent System Conﬁguration Vertical Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Wall and Ceiling Penetration FramingSecuring and Leveling the Appliance Installing Outside Air Kit Damper Assem- blyAppliance Preparation Gas and Electrical ConnectionsSecuring Vent Sections Installing Vent PipeAssembly of Vent Sections Install Attic Insulation ShieldGas Connection Gas InformationFuel Conversion Gas PressureCode CSA C22.1 Wiring RequirementsOptional Accessories Requirements Electrical InformationIgnition Module 3 VAC Transformer PLUG-IN Wall Switch Installation for Fan Optional Junction Box InstallationFinishing Dimensions of CombustiblesFacing Material Noncombustible Facing DiagramAppliance Setup Install the Log Assembly PIN Hole Air Shutter Setting Install the MeshInstall Trim and/or Surround Install HoodSymptom Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System Ues to spark, and main Reference Materials Appliance Dimension DiagramService Parts Log Set AssemblyAt Depot Service Parts ListSL-750TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-E Stocked SL-950TV-IPI-ESL-550 / 750 / 950TV-IPI-E IPI Valve AssemblyContact Information