Heat & Glo LifeStyle SL-550TV-IPI-E owner manual Facing Material, Noncombustible Facing Diagram

Page 32

B. Facing Material

•Metal front faces may be covered with non-combustible materials only.

•Facing and/or ﬁnishing materials must not interfere with air ﬂow through louvers, operation of louvers or doors, or access for service.

•Facing and/or ﬁnishing materials must never overhang into the glass opening.

•Observe all clearances when applying combustible materials.

•Seal joints between the ﬁnished wall and appliance top and sides using a 300 °F minimum sealant. Refer to Figure 13.5 and 13.6.

WARNING! Risk of Fire! DO NOT apply combustible materials beyond the minimum clearances. Comply with all minimum clearances to combustibles as speciﬁed in this manual. Overlapping materials could ignite and will interfere with proper operation of doors and louvers.

NON-COMBUSTIBLE STRIP SHIPPED WITH UNIT

Finish wall material may be combustible - Top and Sides

1 in.	0 in.
0 in.	0 in.

High Temperature Sealant (300° F/149° C min.)

Top and Side Seal Joint

Figure 13.5 Noncombustible Facing Diagram

TOP SEAL	FINISH WALL MATERIAL
TOP SEAL	MAY BE COMBUSTIBLE
JOINT	TOP AND SIDES
SIDE SEAL
JOINT
	1 INCH
	(25 mm)
0 INCH
(0 mm)
NON-COMBUSTIBLE STRIP
SHIPPED WITH UNIT
Figure 13.6 Noncombustible Facing Diagram

32	Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. J • 12/09

Image 32

Contents SL-550TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-E What to do if you smell gasCongratulations Homeowner Reference InformationTable of Contents User GuideReference Materials Appliance SetupTroubleshooting Limited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Appliance CertiﬁcationTempered Glass Speciﬁcations BTU SpeciﬁcationsHigh Altitude Installations Non-Combustible Materials SpeciﬁcationCombustible Materials Speciﬁcation Electrical CodesYour Fireplace Gas Fireplace SafetyOperating Instructions User Guide Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesFan Kit optional Decorative Doors and FrontsLighting Instructions IPI Final inspection byFrequently Asked Questions After Fireplace is LitMaintenance and Service Maintenance Tasks-HomeownerGlass Cleaning Remote ControlMaintenance Tasks-Qualiﬁed Service Technician Gasket Seal and Glass Assembly InspectionVenting LogsEither cobrahead or SIT Getting Started Typical Appliance SystemInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Negative Pressure Framing and Clearances Selecting Appliance LocationConstructing the Appliance Chase ClearancesMantel and Wall Projections Combustible MantelsTermination Locations Vent Termination Minimum ClearancesVent System Conﬁguration Vent Information and DiagramsVent Guidelines Vent Clearances and Framing Pipe Clearances to CombustiblesWall and Ceiling Penetration Framing Vertical Penetration FramingInstalling Outside Air Kit Damper Assem- bly Appliance PreparationGas and Electrical Connections Securing and Leveling the ApplianceInstalling Vent Pipe Assembly of Vent SectionsInstall Attic Insulation Shield Securing Vent SectionsGas Information Fuel ConversionGas Pressure Gas ConnectionWiring Requirements Optional Accessories RequirementsElectrical Information Code CSA C22.1Ignition Module 3 VAC Transformer PLUG-IN Junction Box Installation Wall Switch Installation for Fan OptionalDimensions of Combustibles FinishingNoncombustible Facing Diagram Facing MaterialAppliance Setup Install the Log Assembly PIN Hole Install the Mesh Install Trim and/or SurroundInstall Hood Air Shutter SettingIntelliﬁre Ignition System TroubleshootingSymptom Possible Cause Corrective Action Ues to spark, and main Appliance Dimension Diagram Reference MaterialsLog Set Assembly Service PartsService Parts List At DepotSL-750TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-E SL-950TV-IPI-E StockedIPI Valve Assembly SL-550 / 750 / 950TV-IPI-EContact Information