Heat & Glo LifeStyle SL-550TV-IPI-E owner manual Vent Information and Diagrams, Vent Guidelines

Page 23

7 Vent Information and Diagrams

A. Vent Guidelines

WARNING! Risk of Fire and Asphyxiation! This appliance requires the specified pipe for operation. Incorrect pipe may cause spillage, condensation and overheating.

These models require the following size B-vent double wall, or single wall rigid or flex vent pipe.

Models

Pipe Size

SL-550TV-IPI-E

5 inch

SL-750TV-IPI-E

5 inch

SL-950TV-IPI-E

6 inch

•Follow pipe manufacturer’s installation guidelines when installing the appliance.

WARNING! Risk of Fire, Explosion or Asphyxiation! DO NOT connect this gas appliance to a chimney flue serving a separate solid-fuel or gas burning appliance.

•Vent this appliance directly outside.

•Use separate vent system for this appliance.

May impair safe operation of this appliance or other appli- ances connected to the flue.

B. Vent System Configuration

CAUTION! Risk of Fire! ALL vent configuration speci- fications MUST be followed. This product is tested and listed to these specifications. Appliance performance will suffer if specifications are not followed.

Rise to Run Ratio = 2:1

Maximum Total Horizontal Run = 15 Feet Minimum Total Vertical Rise = 9 Feet Maximum Total Vertical Rise = 48 Feet Maximum Number of Elbows: Two 90º or Four 45º

WARNING! Risk of Fire or Explosion! Insulation and other combustibles must not infringe on clearances.

•ALWAYS maintain specified clearances around venting and firestop systems.

•Install firestops as specified.

Failure to keep insulation or other material away from vent pipe may cause fire.

 

MINIMUM CLEARANCES

 

ARE PER VENT

 

MANUFACTURER’S

 

SPECIFICATIONS

 

METAL

9 FEET

PLUMBER’S

STRAP

MINIMUM

 

48 FEET

MAXIMUM

VENT SUPPORTS ARE PER

VENT MANUFACTURER’S

SPECIFICATIONS

Figure 7.1

Note: Horizontal runs require

 

1/4 in. rise per foot run.

 

VENT SUPPORTS

 

ARE PER VENT

METAL

MANUFACTURER'S

SPECIFICATIONS.

PLUMBERS' STRAP

MAXIMUM HORIZONTAL RUN IS 50%

OF VERTICAL. HORIZONTAL RUN

CANNOT BE MORE THAN 15 FT.

Figure 7.2

 

 

MAXIMUM

 

HORIZONTAL

 

15 FEET

MINIMUM VERTICAL 9 FEET

45DEGREES ELBOW

90DEGREES ELBOW

Figure 7.3

OFFSETS EXCEEDING 45 DEGREES ADAPT HORIZONTAL LIMITATIONS

Note: Maximum horizontal distance is 50% vertical vent height.

Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. J • 12/09

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents What to do if you smell gas SL-550TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-EHomeowner Reference Information CongratulationsUser Guide Table of ContentsReference Materials Appliance SetupTroubleshooting Limited Lifetime Warranty Limited Lifetime Warranty BTU Specifications Listing and Code ApprovalsAppliance Certification Tempered Glass SpecificationsElectrical Codes High Altitude InstallationsNon-Combustible Materials Specification Combustible Materials SpecificationYour Fireplace Gas Fireplace SafetyOperating Instructions User Guide Decorative Doors and Fronts Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Fan Kit optionalFinal inspection by Lighting Instructions IPIAfter Fireplace is Lit Frequently Asked QuestionsRemote Control Maintenance and ServiceMaintenance Tasks-Homeowner Glass CleaningLogs Maintenance Tasks-Qualified Service TechnicianGasket Seal and Glass Assembly Inspection VentingEither cobrahead or SIT Typical Appliance System Getting StartedInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Negative Pressure Selecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseCombustible Mantels Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsVent System Configuration Vent Information and DiagramsVent Guidelines Vertical Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Wall and Ceiling Penetration FramingSecuring and Leveling the Appliance Installing Outside Air Kit Damper Assem- blyAppliance Preparation Gas and Electrical ConnectionsSecuring Vent Sections Installing Vent PipeAssembly of Vent Sections Install Attic Insulation ShieldGas Connection Gas InformationFuel Conversion Gas PressureCode CSA C22.1 Wiring RequirementsOptional Accessories Requirements Electrical InformationIgnition Module 3 VAC Transformer PLUG-IN Wall Switch Installation for Fan Optional Junction Box InstallationFinishing Dimensions of CombustiblesFacing Material Noncombustible Facing DiagramAppliance Setup Install the Log Assembly PIN Hole Air Shutter Setting Install the MeshInstall Trim and/or Surround Install HoodIntellifire Ignition System TroubleshootingSymptom Possible Cause Corrective Action Ues to spark, and main Reference Materials Appliance Dimension DiagramService Parts Log Set AssemblyAt Depot Service Parts ListSL-750TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-E Stocked SL-950TV-IPI-ESL-550 / 750 / 950TV-IPI-E IPI Valve AssemblyContact Information
Top Page Image Contents