Official RIDGID TS3650 Manual: Comprehensive Guide and Resources

.SP6498 Belt Drive Saw 05/03 7/15/03 7:04 AM Page 17

Herc-U-Lift™ Caster Carton			Item	Description	Qty.
Item	Description	Qty.	Item	Description	Qty.
A	Channel Rear	1	E	Tube Front 13-7/8" Long	.......2
B	Tube U-Bolt 19-5/8" Long	1	F	Caster Swivel 3"	4
C	Tube Support 17-1/4" Long ...1		G	Tube Rear 27" Long	2
D	Plate Assembly	1	H	Blister Pack - Hardware	1

Loose Parts

G

H

Assembly

Installing Bevel Handwheel

1. Locate the following hardware:

1 Pan Head Screw with Lockwasher, 1/4-20 x 5/8" long

1 Lockwashers, 1/4 External Type From among the loose parts, find the following:

2Handwheels

2.Line up flat spots on shaft and hand-wheel, push handwheel onto shaft. Install screw and lockwasher to lock handwheel on shaft. Repeat for the other handwheel.

1/4-20 x 5/8

Pan Head Screw with

Lockwasher

Handwheel

Pan Head Screw with Lockwasher

Bevel Handwheel

Shaft

17

Image 17

RIDGID TS3650 manual Assembly, Herc-U-Lift Caster Carton Description Qty, Loose Parts, Installing Bevel Handwheel

Contents

TS3650 Table of Contents Safety Signal Words Before Using The Saw Safety Instructions For Table Saw Before Each Use When Installing Or Moving The SawReduce the Risk of Dangerous Environment To reduce the risk of injury from unexpected saw movement Inspect Your Blade Plan Ahead To Protect Your Eyes, Hands, Face and Ears Dress for safetyPlan your work Inspect your workpiece Reduce the Risk of Accidental Starting Whenever Sawblade Is SpinningKeep Children Away Don’t Force Tool Additional Safety Instructions For Glossary of Terms for Woodworking Featherboard DadoFreehand Gum General Electrical Connections Motor Specifications and Electrical RequirementsPower Supply and Motor Specifications Volt, 60 Hz. Tool Information Changing Motor Voltage Motor Thermal Overload Protector Wire Sizes Unpacking and Checking Contents Operators Manuals List of Loose Parts Part Name Qty Installing Bevel Handwheel AssemblyHerc-U-Lift Caster Carton Description Qty Loose Parts Assembling Leg Stand Installing Elevation Handwheel Miter Gauge Rip Fence Storage Hook End Panel Screw Head Leg Mounting Your Saw Assembling Table Extensions Checking Table Insert To check for parallelism Minimum Clearance Rear Saw If blade is square to table Checking Blade Tilt, or Squareness of Blade to TableTo check for squareness, 90 position If blade is 45 to table To check for alignment, 45 Position Upper Assembly Assembling Herc-U-Lift Caster System Assembly Tips Lower Assembly Center Frames Equal Distance on Each Side Tighten All Nuts Operation of Herc-U-Lift Caster System Installing Front Rip Fence Guide Bar Installing Rear Fence Guide Bar Aligning Rip Fence Guide Bars Adjusting Rip Fence Guide Bars Installing Shims Installing Spacer Bar Rip Fence Lock Lever Adjustment Installing Blade Guard Adjusting Fence Indicator Aligning Blade Guard Mounting the Motor Installing Belt Guard Installing Belt 10-32 Mounting Switch and End Caps Mounting Switch on Left Side Mounting Switch on Right SideSwitch Mounted on Right Side Switch Mounted on Left Side Getting to Know Your Table Saw On-Off Switch Raise blade guard. C. Loosen insert screw Removing or installing sawblade Switch OFF and remove plug From power source outlet beforeTurn Switch OFF and remove Plug From Power source outlet Storage Hooks Conveniently holds rip fence Miter gauge when not in use Sawdust Ejection Port Remove the Existing Table Insert Installing Zero Clearance Insert/Sawblade Operation Tips Installing Zero Clearance Insert/Dado Blades Before Each Use Safety Instructions for Basic Saw OperationsInspect your saw Plan your work Inspect your work areaInspect your workpiece Plan your cut Reduce the Risk of Accidental Starting Work Feed Devices Attaching Wood Face Board Making the base Push Block Making the handle Auxiliary FencePutting it Together Making the side Work Support for Material over Wide Install extension Using the Miter Gauge Additional Safety Instructions for CrosscuttingBasic Saw Operations Crosscutting Repetitive Crosscutting Compound Crosscutting Miter CrosscuttingBevel Crosscutting Additional Safety Instructions for Rip Cuts Using the Rip Fence Once the trailing end is on the table Ripping Bevel Ripping Narrow Work Using Featherboards for Non Thru-Sawing Using Featherboards for Thru- Sawing Resawing Dadoing Using Carbide Tipped Blades Ploughing and Molding Rabbeting Molding Miter Gauge Adjusting Stop Screws Adjustments Herc-U-Lift Caster System MaintenanceMaintaining Your Table Saw Lubrication Ridgid Recommends the Following AccessoriesSKU No Miter Gauge Hold Down AC1022 240V 240V Wiring Diagrams120V Troubleshooting Troubleshooting Troubleshooting SP6498 Belt Drive Saw 05/03 7/15/03 705 AM Catalog No. TS3650 Model No TS36500 Serial No RIDGID, INC