Volt, 60 Hz. Tool Information | RIDGID TS3650 specification

.SP6498 Belt Drive Saw 05/03 7/15/03 7:04 AM Page 12

Motor Specifications and Electrical Requirements (continued)

110-120 Volt, 60 Hz. Tool Information

The plug supplied on your tool may not fit into the outlet you are planning to use. Your local electrical code may require slightly different power cord plug connections. If these differences exist refer to and make the proper adjustments per your local code before your tool is plugged in and turned on.

In the event of a malfunction or break- down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug, as shown. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified electrician.

Improper connection of the equipment- grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.

If the grounding instructions are not completely understood, or if you are in doubt as to whether the tool is properly grounded check with a qualified electrician or service personnel.

WARNING: If not properly grounded, this tool can cause an electrical shock, particularly when used in damp locations, in proximity to plumbing, or out of doors. If an electrical shock occurs there is the potential of a secondary hazard, such as your hands contacting the sawblade.

12

Image 12

RIDGID TS3650 manual Volt, 60 Hz. Tool Information

Contents

TS3650 Table of Contents Safety Instructions For Table Saw Safety Signal Words Before Using The Saw When Installing Or Moving The Saw Before Each UseReduce the Risk of Dangerous Environment To reduce the risk of injury from unexpected saw movement Inspect Your Blade Dress for safety Plan Ahead To Protect Your Eyes, Hands, Face and EarsPlan your work Inspect your workpiece Whenever Sawblade Is Spinning Reduce the Risk of Accidental StartingKeep Children Away Don’t Force Tool Additional Safety Instructions For Glossary of Terms for Woodworking Dado FeatherboardFreehand Gum Motor Specifications and Electrical Requirements Power Supply and Motor SpecificationsGeneral Electrical Connections Volt, 60 Hz. Tool Information Changing Motor Voltage Wire Sizes Motor Thermal Overload Protector Unpacking and Checking Contents List of Loose Parts Part Name Qty Operators Manuals Assembly Installing Bevel HandwheelHerc-U-Lift Caster Carton Description Qty Loose Parts Installing Elevation Handwheel Assembling Leg Stand Miter Gauge Rip Fence Storage Hook End Panel Screw Head Leg Mounting Your Saw Assembling Table Extensions Checking Table Insert To check for parallelism Minimum Clearance Rear Saw Checking Blade Tilt, or Squareness of Blade to Table To check for squareness, 90 positionIf blade is square to table To check for alignment, 45 Position If blade is 45 to table Assembling Herc-U-Lift Caster System Assembly Tips Upper Assembly Lower Assembly Center Frames Equal Distance on Each Side Tighten All Nuts Operation of Herc-U-Lift Caster System Installing Front Rip Fence Guide Bar Installing Rear Fence Guide Bar Adjusting Rip Fence Guide Bars Installing Shims Aligning Rip Fence Guide Bars Installing Spacer Bar Rip Fence Lock Lever Adjustment Adjusting Fence Indicator Installing Blade Guard Aligning Blade Guard Mounting the Motor Installing Belt Installing Belt Guard Mounting Switch and End Caps 10-32 Mounting Switch on Right Side Mounting Switch on Left SideSwitch Mounted on Right Side Switch Mounted on Left Side On-Off Switch Getting to Know Your Table Saw Raise blade guard. C. Loosen insert screw Switch OFF and remove plug From power source outlet before Removing or installing sawbladeTurn Switch OFF and remove Plug From Power source outlet Miter gauge when not in use Storage Hooks Conveniently holds rip fence Sawdust Ejection Port Installing Zero Clearance Insert/Sawblade Remove the Existing Table Insert Installing Zero Clearance Insert/Dado Blades Operation Tips Safety Instructions for Basic Saw Operations Inspect your sawBefore Each Use Inspect your work area Plan your workInspect your workpiece Plan your cut Reduce the Risk of Accidental Starting Work Feed Devices Attaching Wood Face Board Push Block Making the base Auxiliary Fence Making the handlePutting it Together Making the side Install extension Work Support for Material over Wide Additional Safety Instructions for Crosscutting Using the Miter GaugeBasic Saw Operations Crosscutting Repetitive Crosscutting Miter Crosscutting Bevel CrosscuttingCompound Crosscutting Using the Rip Fence Additional Safety Instructions for Rip Cuts Ripping Once the trailing end is on the table Bevel Ripping Narrow Work Using Featherboards for Thru- Sawing Using Featherboards for Non Thru-Sawing Resawing Using Carbide Tipped Blades Dadoing Rabbeting Ploughing and Molding Molding Adjustments Miter Gauge Adjusting Stop Screws Maintenance Maintaining Your Table SawHerc-U-Lift Caster System Ridgid Recommends the Following Accessories LubricationSKU No Miter Gauge Hold Down AC1022 240V Wiring Diagrams 120V240V Troubleshooting Troubleshooting Troubleshooting SP6498 Belt Drive Saw 05/03 7/15/03 705 AM Catalog No. TS3650 Model No TS36500 Serial No RIDGID, INC