Mounting Your Saw | RIDGID TS3650 manual

.SP6498 Belt Drive Saw 05/03 7/15/03 7:04 AM Page 20

Assembly (continued)

Mounting Your Saw

1.Place the saw upside down onto a smooth piece of cardboard or heavy paper, on the floor, so the saw is resting on the table top.

WARNING: The saw is heavy. To reduce the risk of back injury, get help to lift the saw. Hold the saw close to your body. Bend your knees so you can lift with your legs, not your back.

2.Place legs on saw so that holes in saw base and leg set line up and trim label is facing front.

3.Install screws and serrated flange hex nuts as shown.

4.Tighten all leg assembly and mounting hardware at this time.

Serrated

Flange

Hex Nut

	Leg
Screw	Base
	Base

Typical On

Each Leg

20

Image 20

RIDGID TS3650 manual Mounting Your Saw

Contents

TS3650 Table of Contents Safety Instructions For Table Saw Safety Signal Words Before Using The Saw When Installing Or Moving The Saw Before Each UseReduce the Risk of Dangerous Environment To reduce the risk of injury from unexpected saw movement Inspect Your Blade Dress for safety Plan Ahead To Protect Your Eyes, Hands, Face and EarsPlan your work Inspect your workpiece Whenever Sawblade Is Spinning Reduce the Risk of Accidental StartingKeep Children Away Don’t Force Tool Additional Safety Instructions For Glossary of Terms for Woodworking Dado FeatherboardFreehand Gum General Electrical Connections Motor Specifications and Electrical RequirementsPower Supply and Motor Specifications Volt, 60 Hz. Tool Information Changing Motor Voltage Wire Sizes Motor Thermal Overload Protector Unpacking and Checking Contents List of Loose Parts Part Name Qty Operators Manuals Assembly Installing Bevel HandwheelHerc-U-Lift Caster Carton Description Qty Loose Parts Installing Elevation Handwheel Assembling Leg Stand Miter Gauge Rip Fence Storage Hook End Panel Screw Head Leg Mounting Your Saw Assembling Table Extensions Checking Table Insert To check for parallelism Minimum Clearance Rear Saw If blade is square to table Checking Blade Tilt, or Squareness of Blade to TableTo check for squareness, 90 position To check for alignment, 45 Position If blade is 45 to table Assembling Herc-U-Lift Caster System Assembly Tips Upper Assembly Lower Assembly Center Frames Equal Distance on Each Side Tighten All Nuts Operation of Herc-U-Lift Caster System Installing Front Rip Fence Guide Bar Installing Rear Fence Guide Bar Adjusting Rip Fence Guide Bars Installing Shims Aligning Rip Fence Guide Bars Installing Spacer Bar Rip Fence Lock Lever Adjustment Adjusting Fence Indicator Installing Blade Guard Aligning Blade Guard Mounting the Motor Installing Belt Installing Belt Guard Mounting Switch and End Caps 10-32 Mounting Switch on Right Side Mounting Switch on Left SideSwitch Mounted on Right Side Switch Mounted on Left Side On-Off Switch Getting to Know Your Table Saw Raise blade guard. C. Loosen insert screw Switch OFF and remove plug From power source outlet before Removing or installing sawbladeTurn Switch OFF and remove Plug From Power source outlet Miter gauge when not in use Storage Hooks Conveniently holds rip fence Sawdust Ejection Port Installing Zero Clearance Insert/Sawblade Remove the Existing Table Insert Installing Zero Clearance Insert/Dado Blades Operation Tips Before Each Use Safety Instructions for Basic Saw OperationsInspect your saw Inspect your work area Plan your workInspect your workpiece Plan your cut Reduce the Risk of Accidental Starting Work Feed Devices Attaching Wood Face Board Push Block Making the base Auxiliary Fence Making the handlePutting it Together Making the side Install extension Work Support for Material over Wide Additional Safety Instructions for Crosscutting Using the Miter GaugeBasic Saw Operations Crosscutting Repetitive Crosscutting Compound Crosscutting Miter CrosscuttingBevel Crosscutting Using the Rip Fence Additional Safety Instructions for Rip Cuts Ripping Once the trailing end is on the table Bevel Ripping Narrow Work Using Featherboards for Thru- Sawing Using Featherboards for Non Thru-Sawing Resawing Using Carbide Tipped Blades Dadoing Rabbeting Ploughing and Molding Molding Adjustments Miter Gauge Adjusting Stop Screws Herc-U-Lift Caster System MaintenanceMaintaining Your Table Saw Ridgid Recommends the Following Accessories LubricationSKU No Miter Gauge Hold Down AC1022 240V 240V Wiring Diagrams120V Troubleshooting Troubleshooting Troubleshooting SP6498 Belt Drive Saw 05/03 7/15/03 705 AM Catalog No. TS3650 Model No TS36500 Serial No RIDGID, INC