Motor Specifications and Electrical Requirements | RIDGID TS3650

.SP6498 Belt Drive Saw 05/03 7/15/03 7:04 AM Page 11

Sawblade Path

The area of the workpiece or table top directly in line with either the travel of the blade or the part of the workpiece which will be, or has been, cut by the blade.

Set

The distance that the tip of the sawblade tooth is bent (or set) outward from the face of the blade.

Throw-Back

Throwing of pieces in a manner similar to a kickback.

Thru-Sawing

Any cutting operation where the blade extends completely through the thickness of the workpiece.

Trailing End

The workpiece end last cut by the blade in a ripping operation.

Workpiece

The item on which the cutting operation is being performed. The surfaces of a work-piece are commonly referred to as faces, ends, and edges.

Motor Specifications and Electrical Requirements

Power Supply and Motor Specifications

WARNING: To reduce the risk of electrical hazards, fire hazards or damage to the tool, use proper circuit protection. Your tool is wired at the factory for operation using the voltage shown. Connect tool to a power line with the appropriate voltage and a 15-amp branch circuit. Use a 15-amp time delay type fuse or circuit breaker. To reduce the risk of shock or fire, if power cord is worn or cut, or damaged in any way, have it replaced immediately.

The A-C motor used on this tool is a totally enclosed fan cooled (TEFC) capacitor start, capacitor run non-reversible type, having the following specifications. It is wired at the factory for operation on 110-120v AC, 60 Hz. service.

136.5

General Electrical Connections

WARNING: To reduce the risk of electrocution:

1.Use only identical replacement parts when servicing. Servicing should be performed by a qualified service technician.

2.Do not use in rain or where floor is wet.

This tool is intended for indoor residential use only.

WARNING: Do not permit fingers to touch the terminals of plug when installing or removing the plug to or from the outlet.

11

Image 11

RIDGID TS3650 manual Motor Specifications and Electrical Requirements, Power Supply and Motor Specifications

Contents

TS3650 Table of Contents Safety Signal Words Before Using The Saw Safety Instructions For Table Saw To reduce the risk of injury from unexpected saw movement When Installing Or Moving The SawBefore Each Use Reduce the Risk of Dangerous Environment Inspect Your Blade Inspect your workpiece Dress for safetyPlan Ahead To Protect Your Eyes, Hands, Face and Ears Plan your work Don’t Force Tool Whenever Sawblade Is SpinningReduce the Risk of Accidental Starting Keep Children Away Additional Safety Instructions For Glossary of Terms for Woodworking Gum DadoFeatherboard Freehand General Electrical Connections Motor Specifications and Electrical RequirementsPower Supply and Motor Specifications Volt, 60 Hz. Tool Information Changing Motor Voltage Motor Thermal Overload Protector Wire Sizes Unpacking and Checking Contents Operators Manuals List of Loose Parts Part Name Qty Loose Parts AssemblyInstalling Bevel Handwheel Herc-U-Lift Caster Carton Description Qty Assembling Leg Stand Installing Elevation Handwheel Miter Gauge Rip Fence Storage Hook End Panel Screw Head Leg Mounting Your Saw Assembling Table Extensions Checking Table Insert To check for parallelism Minimum Clearance Rear Saw If blade is square to table Checking Blade Tilt, or Squareness of Blade to TableTo check for squareness, 90 position If blade is 45 to table To check for alignment, 45 Position Upper Assembly Assembling Herc-U-Lift Caster System Assembly Tips Lower Assembly Center Frames Equal Distance on Each Side Tighten All Nuts Operation of Herc-U-Lift Caster System Installing Front Rip Fence Guide Bar Installing Rear Fence Guide Bar Aligning Rip Fence Guide Bars Adjusting Rip Fence Guide Bars Installing Shims Installing Spacer Bar Rip Fence Lock Lever Adjustment Installing Blade Guard Adjusting Fence Indicator Aligning Blade Guard Mounting the Motor Installing Belt Guard Installing Belt 10-32 Mounting Switch and End Caps Switch Mounted on Left Side Mounting Switch on Right SideMounting Switch on Left Side Switch Mounted on Right Side Getting to Know Your Table Saw On-Off Switch Raise blade guard. C. Loosen insert screw Plug From Power source outlet Switch OFF and remove plug From power source outlet beforeRemoving or installing sawblade Turn Switch OFF and remove Storage Hooks Conveniently holds rip fence Miter gauge when not in use Sawdust Ejection Port Remove the Existing Table Insert Installing Zero Clearance Insert/Sawblade Operation Tips Installing Zero Clearance Insert/Dado Blades Before Each Use Safety Instructions for Basic Saw OperationsInspect your saw Plan your cut Inspect your work areaPlan your work Inspect your workpiece Reduce the Risk of Accidental Starting Work Feed Devices Attaching Wood Face Board Making the base Push Block Making the side Auxiliary FenceMaking the handle Putting it Together Work Support for Material over Wide Install extension Crosscutting Additional Safety Instructions for CrosscuttingUsing the Miter Gauge Basic Saw Operations Repetitive Crosscutting Compound Crosscutting Miter CrosscuttingBevel Crosscutting Additional Safety Instructions for Rip Cuts Using the Rip Fence Once the trailing end is on the table Ripping Bevel Ripping Narrow Work Using Featherboards for Non Thru-Sawing Using Featherboards for Thru- Sawing Resawing Dadoing Using Carbide Tipped Blades Ploughing and Molding Rabbeting Molding Miter Gauge Adjusting Stop Screws Adjustments Herc-U-Lift Caster System MaintenanceMaintaining Your Table Saw Miter Gauge Hold Down AC1022 Ridgid Recommends the Following AccessoriesLubrication SKU No 240V 240V Wiring Diagrams120V Troubleshooting Troubleshooting Troubleshooting SP6498 Belt Drive Saw 05/03 7/15/03 705 AM Catalog No. TS3650 Model No TS36500 Serial No RIDGID, INC