Heat & Glo LifeStyle SL-550TV-IPI-E, SL-950TV-IPI-E Ignition Module 3 VAC Transformer PLUG-IN

Page 29

IGNITION

MODULE 3 VAC

TRANSFORMER 3V

PLUG-IN

	BLACK
RED	BROWN
RED

BLACK

BATTERY PACK

BROWN

INTERMITTENT

PILOT IGNITOR

I

S

WHITE

ORG

GROUND TO

FIREPLACE CHASSIS

ORG

GREEN

TEMP SENSOR	BLACK
	VALVE

THERMOSTAT WIRE ASSEMBLY

NOTE: 1. Ignition module, valve, pilot, and wall switch operate on 3 volts. 120 VAC is required at junction box unless equipped with battery back-up.

Figure 12.1 Intelliﬁre Pilot Ignition (IPI) Wiring Diagram with Wall Switch or Thermostat

IGNITION

INTERMITTENT

PILOT IGNITOR

I

MODULE 3 VAC

S

TRANSFORMER 3V	WHITE
	ORG
	GROUND TO
PLUG-IN	FIREPLACE CHASSIS
BLACK

RED

BLACK

BATTERY PACK

PLUG IN

BROWN

BROWN

ORG

GREEN

TEMP SENSOR

BLACK

REMOTE RECEIVER

VALVE

NOTE: 1. Ignition module, valve, pilot, and wall switch operate on 3 volts. 120 VAC is required at junction box unless equipped with battery back-up.

Figure 12.2 Intelliﬁre Pilot Ignition (IPI) Wiring Diagram with Remote Receiver

Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. J • 12/09

29

Image 29

Contents What to do if you smell gas SL-550TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-EHomeowner Reference Information CongratulationsUser Guide Table of ContentsReference Materials Appliance SetupTroubleshooting Limited Lifetime Warranty Limited Lifetime Warranty Appliance Certiﬁcation Listing and Code ApprovalsTempered Glass Speciﬁcations BTU SpeciﬁcationsNon-Combustible Materials Speciﬁcation High Altitude InstallationsCombustible Materials Speciﬁcation Electrical CodesYour Fireplace Gas Fireplace SafetyOperating Instructions User Guide Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyFan Kit optional Decorative Doors and FrontsFinal inspection by Lighting Instructions IPIAfter Fireplace is Lit Frequently Asked QuestionsMaintenance Tasks-Homeowner Maintenance and ServiceGlass Cleaning Remote ControlGasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualiﬁed Service TechnicianVenting LogsEither cobrahead or SIT Typical Appliance System Getting StartedInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Negative Pressure Selecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseCombustible Mantels Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsVent System Conﬁguration Vent Information and DiagramsVent Guidelines Pipe Clearances to Combustibles Vent Clearances and FramingWall and Ceiling Penetration Framing Vertical Penetration FramingAppliance Preparation Installing Outside Air Kit Damper Assem- blyGas and Electrical Connections Securing and Leveling the ApplianceAssembly of Vent Sections Installing Vent PipeInstall Attic Insulation Shield Securing Vent SectionsFuel Conversion Gas InformationGas Pressure Gas ConnectionOptional Accessories Requirements Wiring RequirementsElectrical Information Code CSA C22.1Ignition Module 3 VAC Transformer PLUG-IN Wall Switch Installation for Fan Optional Junction Box InstallationFinishing Dimensions of CombustiblesFacing Material Noncombustible Facing DiagramAppliance Setup Install the Log Assembly PIN Hole Install Trim and/or Surround Install the MeshInstall Hood Air Shutter SettingIntelliﬁre Ignition System TroubleshootingSymptom Possible Cause Corrective Action Ues to spark, and main Reference Materials Appliance Dimension DiagramService Parts Log Set AssemblyAt Depot Service Parts ListSL-750TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-E Stocked SL-950TV-IPI-ESL-550 / 750 / 950TV-IPI-E IPI Valve AssemblyContact Information