Heat & Glo LifeStyle SL-750TV-IPI-E, SL-950TV-IPI-E Finishing, Dimensions of Combustibles

Page 31

13 Finishing

A. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clear- ances as speciﬁed. Framing closer than the minimums list- ed must be constructed entirely of noncombustible materi- als (i.e., steel studs, concrete board, etc.) Failure to comply could cause ﬁre.

Combustible Mantels

	CEILING
	12
	11
	10
	9
7	8	32
7		32
6
5	12 13
4	12 13

TOP VIEW

2-7/8 IN.

MINIMUM

Note: Clearance from opening Alcove/Mantel leg.

1/2 IN.

MINIMUM

3FT.

MAXIMUM

3					7		8	9	10 11
3									10 11


			6
		5
4		5

TOP OF HOOD OR FIREPLACE OPENING

Note: All measurements are in inches.

Figure 13.1 Minimum Vertical and Maximum Horizontal

Figure 13.3 Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening)

Dimensions of Combustibles

	1/2 in.
3-1/2 in.	SHEETROCK

NON-COMBUSTIBLE

BOARD SHIPPED

WITH APPLIANCE

TOP VIEW

5-3/8 IN.

MINIMUM

Note: Clearance from opening Alcove/Mantel leg.

3 IN.

MINIMUM

UNLIMITED

1/2 in.

Figure 13.4 Non-Combustible Mantel Leg or Wall Projections (Acceptable on both sides of opening)

NON-COMBUSTIBLE ZONE

Figure 13.2 Minimum Vertical and Maximum Horizontal

Dimensions of Non-Combustibles

Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. J • 12/09

31

Image 31

Contents What to do if you smell gas SL-550TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-EHomeowner Reference Information CongratulationsUser Guide Table of ContentsTroubleshooting Appliance SetupReference Materials Limited Lifetime Warranty Limited Lifetime Warranty BTU Speciﬁcations Listing and Code ApprovalsAppliance Certiﬁcation Tempered Glass SpeciﬁcationsElectrical Codes High Altitude InstallationsNon-Combustible Materials Speciﬁcation Combustible Materials SpeciﬁcationOperating Instructions User Guide Gas Fireplace SafetyYour Fireplace Decorative Doors and Fronts Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Fan Kit optionalFinal inspection by Lighting Instructions IPIAfter Fireplace is Lit Frequently Asked QuestionsRemote Control Maintenance and ServiceMaintenance Tasks-Homeowner Glass CleaningLogs Maintenance Tasks-Qualiﬁed Service TechnicianGasket Seal and Glass Assembly Inspection VentingEither cobrahead or SIT Typical Appliance System Getting StartedTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Negative Pressure Selecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseCombustible Mantels Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsVent Guidelines Vent Information and DiagramsVent System Conﬁguration Vertical Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Wall and Ceiling Penetration FramingSecuring and Leveling the Appliance Installing Outside Air Kit Damper Assem- blyAppliance Preparation Gas and Electrical ConnectionsSecuring Vent Sections Installing Vent PipeAssembly of Vent Sections Install Attic Insulation ShieldGas Connection Gas InformationFuel Conversion Gas PressureCode CSA C22.1 Wiring RequirementsOptional Accessories Requirements Electrical InformationIgnition Module 3 VAC Transformer PLUG-IN Wall Switch Installation for Fan Optional Junction Box InstallationFinishing Dimensions of CombustiblesFacing Material Noncombustible Facing DiagramAppliance Setup Install the Log Assembly PIN Hole Air Shutter Setting Install the MeshInstall Trim and/or Surround Install HoodSymptom Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System Ues to spark, and main Reference Materials Appliance Dimension DiagramService Parts Log Set AssemblyAt Depot Service Parts ListSL-750TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-E Stocked SL-950TV-IPI-ESL-550 / 750 / 950TV-IPI-E IPI Valve AssemblyContact Information