Heat & Glo LifeStyle 6000 DVTFL, SL-42 DVT Vertical Venting, VERTICAL VENTING V FT 40 MAX. 12.4 M

Page 14

VERTICAL VENTING

V (FT.)

40' MAX. (12.4 M)

NOTE: MODEL 6000 ARCH

A 12-inch length of straight vent pipe MUST be the first vent component attached to the unit.

CAP

Figure 9. Vertical Venting

Image 14

Contents Heat-N-GloFireplace Underwriters Laboratories ListedInstallers Guide 8000 DVTFLPROHIBITED SAFETY AND WARNING INFORMATIONTHIS UNIT IS NOT FOR USE WITH SOLID FUEL Table of Contents Installation Codes Approvals and Codesand Codes High Altitude InstallationsGetting Started Pre-installationPreparationIntroducing the Heat-N-Glo Gas Fireplaces ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARDFigure 1. Diagram of 8000DVTFL Page Figure 3. Diagram of SL-42DVT Clearance Requirements Installing the FireplaceStep Locating the Fireplace COVERING DETAILS, BEFORE FRAMING Step Framing the FireplaceVERIFY FRAMING METHODS AND WALL CONSTRUCTION BEGINSStep Installing the Vent System A. Vent System ApprovalsDV-48D DV-36D DV-90DDV-45D DV-12D4-inchinner pipe/6 5/8-inchouter pipe NOTE MODEL 6000 ARCH Figure 9. Vertical VentingVERTICAL VENTING V FT 40 MAX. 12.4 M NOTE: IF A 90 ELBOW IS FIRST Model 6000XLT & 8000DVTFLFOR SL-42DVT ATTACHED TO THE UNIT, THENOTE MODEL 6000 ARCH VENTING WITH TWO 2 90 ELBOWSFigure 11. Venting with two 90 elbows H1 V HNOTE: MODEL 6000 ARCH VENTING WITH TWO 2 90 ELBOWSFigure 12. Venting with two 90 elbows H V1 VNOTE: MODEL 6000 ARCH VENTING WITH THREE 3 90 ELBOWSFigure 13. Venting with three 90 elbows VENTING WITH THREE 3 90 ELBOWS Figure 14. Venting with three 90 elbowsB. Installing Vent Components ENSURE THAT THE FIBERGLASS Figure 17. Adding Venting Components 3. Install Support BracketsTo install support brackets for horizontal runs •Place the pipe supports around the vent pipeFor Horizontal Runs - Firestops are REQUIRED Figure 18. Installing Support Brackets4. Install Firestops Model DVK-01TRDand SLK-01TRDdo not needFigure 19. Hole and Vent Pipe Figure 21. Hole and New Framing Members Figure 22. Ceiling Firestop Ceiling SideC. Vent Termination Figure 23. Attic FirestopFigure 24. Round and Trapezoid Termination Caps THE VINYL PROTECTOR KIT TO THE TOP OF VINYL SIDING, IT IS NECESSARY TO INSTALLIF EXTERIOR WALLS ARE FINISHED WITH TERMINATION CAPSMAJOR U.S. BUILDING CODES on the outside of the buildingRoof Pitch Step The Gas Control Systems Step Positioning Leveling, and Securing theFireplace 13 mm hook-upat the unit Step The Gas Supply LineFigure 28. Gas Controls Systems DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKSPressure Step Gas Pressure RequirementsFigure 29. Gas Supply Line Natural GasStep Wiring the Fireplace For Standing Pilot Ignition WiringWHEN SERVICING CONTROLS. WIRING Electrical wiring must be installed by a licensedLABEL ALL WIRES PRIOR TO DISCONNECTION ERRORS CAN CAUSE IMPROPER ANDStep Finishing Step Installing Trim Logs, and Ember Material Hearth ExtensionsPlacing the Ember Material Positioning the LogsSave the log instructions with this manual 1.Lift the trim door up and out of the unit Figure 35. Glass AssemblyFigure 36. Placement of the Ember Material Review safety warnings and cautions Lighting the Fireplace After the InstallationStep Before Lighting the Fireplace Step Double-checkfor faulty componentsTURN OFF THE GAS BEFORE SERVICING Fireplace MaintenanceMaintaining and Servicing Your Fireplace YOUR FIREPLACEFigure 37. Burner Flame Patterns Figure 38. Pilot/Ignitor Flame PatternsPART Replacement Parts and AccessoriesStanding Pilot Only PART DESCRIPTIONPART DSI Ignition Only8000DVTFL, 6000DVTFL, 6000ARCH, SL-42DVT PART DESCRIPTIONBoth Standing Pilot and DSI Ignition ACCESSORY AccessoriesBoth Standing Pilot and DSI Ignition Cont PART