Heat & Glo LifeStyle 6000 ARCH, 8000 DVTFL Burner Flame Patterns, Pilot/Ignitor Flame Patterns

Page 42

MAKE SURE THE FLAMES

ARE STEADY—NOT

LIFTING OR FLOATING.

Figure 37. Burner Flame Patterns

STANDING PILOT

3/8" (10 mm)

	NOTE: FLAMES	DSI IGNITION
	NOTE: FLAMES
	TOO CLOSE TO
	THE CERAMIC	IGNITOR
	INSULATORS CAN	IGNITOR
	CAUSE NUISANCE
	LOCKOUTS AND
	ELECTRODE	1/2” (13mm)
	FAILURE.	1/2” (13mm)
	FAILURE.
	CERAMIC
	INSULATOR

3/16" (5 mm)

Figure 38. Pilot/Ignitor Flame Patterns

Image 42

Contents Heat-N-GloFireplace Underwriters Laboratories ListedInstallers Guide 8000 DVTFLSAFETY AND WARNING INFORMATION THIS UNIT IS NOT FOR USE WITH SOLID FUELPROHIBITED Table of Contents Installation Codes Approvals and Codesand Codes High Altitude InstallationsGetting Started Pre-installationPreparationIntroducing the Heat-N-Glo Gas Fireplaces ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARDFigure 1. Diagram of 8000DVTFL Page Figure 3. Diagram of SL-42DVT Installing the Fireplace Step Locating the FireplaceClearance Requirements COVERING DETAILS, BEFORE FRAMING Step Framing the FireplaceVERIFY FRAMING METHODS AND WALL CONSTRUCTION BEGINSStep Installing the Vent System A. Vent System ApprovalsDV-48D DV-36D DV-90DDV-45D DV-12D4-inchinner pipe/6 5/8-inchouter pipe Figure 9. Vertical Venting VERTICAL VENTING V FT 40 MAX. 12.4 MNOTE MODEL 6000 ARCH NOTE: IF A 90 ELBOW IS FIRST Model 6000XLT & 8000DVTFLFOR SL-42DVT ATTACHED TO THE UNIT, THENOTE MODEL 6000 ARCH VENTING WITH TWO 2 90 ELBOWSFigure 11. Venting with two 90 elbows H1 V HNOTE: MODEL 6000 ARCH VENTING WITH TWO 2 90 ELBOWSFigure 12. Venting with two 90 elbows H V1 VVENTING WITH THREE 3 90 ELBOWS Figure 13. Venting with three 90 elbowsNOTE: MODEL 6000 ARCH VENTING WITH THREE 3 90 ELBOWS Figure 14. Venting with three 90 elbowsB. Installing Vent Components ENSURE THAT THE FIBERGLASS Figure 17. Adding Venting Components 3. Install Support BracketsTo install support brackets for horizontal runs •Place the pipe supports around the vent pipeFor Horizontal Runs - Firestops are REQUIRED Figure 18. Installing Support Brackets4. Install Firestops Model DVK-01TRDand SLK-01TRDdo not needFigure 19. Hole and Vent Pipe Figure 21. Hole and New Framing Members Figure 22. Ceiling Firestop Ceiling SideC. Vent Termination Figure 23. Attic FirestopFigure 24. Round and Trapezoid Termination Caps THE VINYL PROTECTOR KIT TO THE TOP OF VINYL SIDING, IT IS NECESSARY TO INSTALLIF EXTERIOR WALLS ARE FINISHED WITH TERMINATION CAPSMAJOR U.S. BUILDING CODES on the outside of the buildingRoof Pitch Step Positioning Leveling, and Securing the FireplaceStep The Gas Control Systems 13 mm hook-upat the unit Step The Gas Supply LineFigure 28. Gas Controls Systems DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKSPressure Step Gas Pressure RequirementsFigure 29. Gas Supply Line Natural GasStep Wiring the Fireplace For Standing Pilot Ignition WiringWHEN SERVICING CONTROLS. WIRING Electrical wiring must be installed by a licensedLABEL ALL WIRES PRIOR TO DISCONNECTION ERRORS CAN CAUSE IMPROPER ANDStep Finishing Step Installing Trim Logs, and Ember Material Hearth ExtensionsPositioning the Logs Save the log instructions with this manualPlacing the Ember Material Figure 35. Glass Assembly Figure 36. Placement of the Ember Material1.Lift the trim door up and out of the unit Review safety warnings and cautions Lighting the Fireplace After the InstallationStep Before Lighting the Fireplace Step Double-checkfor faulty componentsTURN OFF THE GAS BEFORE SERVICING Fireplace MaintenanceMaintaining and Servicing Your Fireplace YOUR FIREPLACEFigure 37. Burner Flame Patterns Figure 38. Pilot/Ignitor Flame PatternsPART Replacement Parts and AccessoriesStanding Pilot Only PART DESCRIPTIONPART DSI Ignition Only8000DVTFL, 6000DVTFL, 6000ARCH, SL-42DVT PART DESCRIPTIONBoth Standing Pilot and DSI Ignition ACCESSORY AccessoriesBoth Standing Pilot and DSI Ignition Cont PART