Heat & Glo LifeStyle 8000 DVTFL, SL-42 DVT, 6000 ARCH manual Step Before Lighting the Fireplace Step

Page 40

Step 11

37

Step 11

Before Lighting

the Fireplace

Step 12

Lighting the

Fireplace

After the

Installation

Before lighting the fireplace, be sure to do the following:

Review safety warnings and cautions

•Read the Safety and Warning Information section at the beginning of this Installers Guide.

Double-check for gas leaks

•Before lighting the fireplace, double-check the unit for possible gas leaks.

Double-check vent terminations and front grilles for obstructions.

•Before lighting the fireplace, double-check the unit for possible obstructions that could be blocking the vent terminations or the front grilles.

Double-check for faulty components

•Any component that is found to be faulty MUST BE replaced with an approved component. Tampering with the fireplace components is DANGEROUS and voids all warranties.

A small amount of air will be in the gas supply lines. When first lighting the fireplace, it will take a few minutes for the lines to purge themselves of this air. Once the purging is complete, the fireplace will light and will operate normally.

Subsequent lightings of the fireplace will not require this purging of air from the gas supply lines, unless the gas valve has been turned to the OFF position, in which case the air would have to be purged.

You’ve reviewed all safety warnings, you’ve checked the fireplace for gas leaks, you know the vent system is unobstructed, and you’ve checked for faulty components. Now you’re ready to light the fireplace.

WARNING

PLEASE REFER TO THE USER’S MANUAL FOR ALL CAUTIONS, SAFETY, AND WARNING INFORMATION PERTAINING TO THE LIGHTING AND OPERATION OF THE FIREPLACE.

LEAVE THIS INSTALLATION MANUAL WITH THE APPLIANCE FOR FUTURE REFERENCE.

Image 40

Contents Underwriters Laboratories Listed Installers GuideHeat-N-GloFireplace 8000 DVTFLTHIS UNIT IS NOT FOR USE WITH SOLID FUEL SAFETY AND WARNING INFORMATIONPROHIBITED Table of Contents Approvals and Codes and CodesInstallation Codes High Altitude InstallationsPre-installationPreparation Introducing the Heat-N-Glo Gas FireplacesGetting Started ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARDFigure 1. Diagram of 8000DVTFL Page Figure 3. Diagram of SL-42DVT Step Locating the Fireplace Installing the FireplaceClearance Requirements Step Framing the Fireplace VERIFY FRAMING METHODS AND WALLCOVERING DETAILS, BEFORE FRAMING CONSTRUCTION BEGINSStep Installing the Vent System A. Vent System ApprovalsDV-90D DV-45DDV-48D DV-36D DV-12D4-inchinner pipe/6 5/8-inchouter pipe VERTICAL VENTING V FT 40 MAX. 12.4 M Figure 9. Vertical VentingNOTE MODEL 6000 ARCH Model 6000XLT & 8000DVTFL FOR SL-42DVTNOTE: IF A 90 ELBOW IS FIRST ATTACHED TO THE UNIT, THEVENTING WITH TWO 2 90 ELBOWS Figure 11. Venting with two 90 elbowsNOTE MODEL 6000 ARCH H1 V HVENTING WITH TWO 2 90 ELBOWS Figure 12. Venting with two 90 elbowsNOTE: MODEL 6000 ARCH H V1 VFigure 13. Venting with three 90 elbows VENTING WITH THREE 3 90 ELBOWSNOTE: MODEL 6000 ARCH VENTING WITH THREE 3 90 ELBOWS Figure 14. Venting with three 90 elbowsB. Installing Vent Components ENSURE THAT THE FIBERGLASS 3. Install Support Brackets To install support brackets for horizontal runsFigure 17. Adding Venting Components •Place the pipe supports around the vent pipeFigure 18. Installing Support Brackets 4. Install FirestopsFor Horizontal Runs - Firestops are REQUIRED Model DVK-01TRDand SLK-01TRDdo not needFigure 19. Hole and Vent Pipe Figure 21. Hole and New Framing Members Figure 22. Ceiling Firestop Ceiling SideC. Vent Termination Figure 23. Attic FirestopFigure 24. Round and Trapezoid Termination Caps VINYL SIDING, IT IS NECESSARY TO INSTALL IF EXTERIOR WALLS ARE FINISHED WITHTHE VINYL PROTECTOR KIT TO THE TOP OF TERMINATION CAPSMAJOR U.S. BUILDING CODES on the outside of the buildingRoof Pitch Fireplace Step Positioning Leveling, and Securing theStep The Gas Control Systems Step The Gas Supply Line Figure 28. Gas Controls Systems13 mm hook-upat the unit DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKSStep Gas Pressure Requirements Figure 29. Gas Supply LinePressure Natural GasStep Wiring the Fireplace For Standing Pilot Ignition WiringElectrical wiring must be installed by a licensed LABEL ALL WIRES PRIOR TO DISCONNECTIONWHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER ANDStep Finishing Step Installing Trim Logs, and Ember Material Hearth ExtensionsSave the log instructions with this manual Positioning the LogsPlacing the Ember Material Figure 36. Placement of the Ember Material Figure 35. Glass Assembly1.Lift the trim door up and out of the unit Lighting the Fireplace After the Installation Step Before Lighting the Fireplace StepReview safety warnings and cautions Double-checkfor faulty componentsFireplace Maintenance Maintaining and Servicing Your FireplaceTURN OFF THE GAS BEFORE SERVICING YOUR FIREPLACEFigure 37. Burner Flame Patterns Figure 38. Pilot/Ignitor Flame PatternsReplacement Parts and Accessories Standing Pilot OnlyPART PART DESCRIPTIONDSI Ignition Only 8000DVTFL, 6000DVTFL, 6000ARCH, SL-42DVTPART PART DESCRIPTIONBoth Standing Pilot and DSI Ignition Accessories Both Standing Pilot and DSI Ignition ContACCESSORY PART