Desa VMH26NRB To Turn OFF GAS To Appliance, Manual Lighting Procedure, Shutting Off Fireplace

Page 23

OPERATING FIREPLACE

Continued

8.Keep control knob pressed in for 30 sec- onds after lighting pilot. After 30 seconds, release control knob.

•If control knob does not pop out when re- leased, contact a qualified service person or gas supplier for repairs.

Note: If pilot goes out, repeat steps 4 through 8.

9.Slightly push in and turn control knob coun-

terclockwise to the ON position.

10.Wait one minute and switch selector switch to the ON position to light burner.

11.Set flame adjustment knob to any level be- tween HI and LO.

CAUTION: Do not try to ad- just heating levels by using the equipment shutoff valve.

WARNING: Make sure the selector switch is in the OFF position when you are away from home for long periods of time. Fireplace will come on automati- cally with selector switch in the ON position.

Pilot

Ignitor

Burner

Electrode

Figure 37 - Propane/LP Gas Pilot

Pilot Burner

Ignitor

Electrode

 

Figure 38 - Natural Gas Pilot

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Fireplace

1.Turn control knob clockwise to the OFF position.

2a. Set selector switch in the OFF position.

2b. If Using Optional Hand-Held Remote: Set selector switch in the OFF position to pre- vent draining battery.

Shutting Off Burners Only (pilot stays lit) You may shut off the burners and keep the pi- lot lit by doing one of the following:

1.Turn control knob clockwise to the PILOT position.

2.Use remote control manual OFF button.

3.Set selector switch in the OFF position.

MANUAL LIGHTING

PROCEDURE

1.Follow steps 1 through 6 under Lighting In- structions, page 22.

2.Depress control knob and light pilot with match.

3.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow steps 9 through 11, Lighting Instructions, column 1.

OPTIONAL HAND-HELD

REMOTE OPERATION

Note: All remote control accessories must be purchased separately (see Accessories, pages 36 and 37). Follow instructions included with the remote control.

NOTICE: You must light the pi- lot before using the hand-held remote control unit. See Light- ing Instructions on page 22.

After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Adjust flame adjustment knob anywhere be- tween HI and LO. Slide the selector switch to the REMOTE position (see Figure 39, page 24). Note: The burner may light if hand-held re- mote was on when selector switch was last turned off. You can now turn the burner on and off with the hand-held remote control unit.

IMPORTANT: Do not leave the selector switch in the REMOTE or ON position when the pilot is not lit. This will drain the battery.

113110-01A

www.desatech.com

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents REMOTE-READY Models VMH26PRB, VMH26NRB, EFS26NRA, EFS26PRA Shown with optional cabinet mantel/hearth base accessoryTable of Contents Safety Information Provide adequate clearances around air openings Product IdentificationLocal Codes Optional Remote Control AccessoriesProduct Features AssemblyUnusually Tight Construction Assembly AIR for Combustion VentilationProviding Adequate Ventilation Determining if You Have a Confined or Unconfined Space AIR for Combustion VentilationDetermining FRESH-AIR Flow for Fireplace Location Confined and Unconfined SpaceVentilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Check GAS Type InstallationInstallation Items Minimum 16 inches from Side Wall BUILT-IN Fireplace InstallationFireplace Clearances Minimum Clearance to Combustible MaterialsRough Opening for Installing Wall Mantel Clearances for Built-In Installation Optional Mantel InstallationAssemblingTrimTrimshippedwithmantel Installing Optional Blower Accessory GA3450TRemoving Upper Louver Assembly and Branch Support Installing Blower Accessory Extension Cord For Built-In InstallationTest to make sure the blower is working properly External Regulator With Vent Pointing Down Connecting to GAS SupplyPropane/LP Connecting Fireplace to GAS SupplyInstallation Items Needed Correct all leaks at once Pressure Testing gas Supply Piping SystemChecking GAS Connections Installing Receiver Pressure Testing Fireplace Gas ConnectionsOptional Wall Mounted Wire harness provided in the fireplace hard- ware packInstalling 9-Volt Battery in Hand-Held Remote Control Unit Remove battery cover on back of remote con- trol unitInstall the base onto the wall with the pro- vided screws Optional Wall Switch GWMS2Installing LOG SET and Screen Operating Fireplace For Your Safety Read Before LightingSelector Switch OFF Position Control Knob Ignitor Button Flame Adjustment KnobShutting Off Fireplace Manual Lighting ProcedureTo Turn OFF GAS To Appliance Optional HAND-HELD Remote OperationThermostat Series Model Ghrctb ON/OFF Series Model GhrcbOperating Blower Optional GWMS2 Wall Mounted Switch OptionalInspecting Burners GWMT1 Wall Mounted Thermostat OptionalBurner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceBurner Flame Pattern Air Passageways Wiring DiagramLOG SET CabinetIgnitor cable dry TroubleshootingObserved Problem Possible Cause Remedy Replace pilot assemblyPressed Safety interlock system hasLow gas pressure ODS/pilot assembly Or improperly connected Diagram,Hours of operation Bris. If found, clean burnerResidues from manufactur Tial operationGas leak. See Warning Remote-Ready Models SpecificationsParts Under Warranty Replacement PartsService Hints Technical ServiceIllustrated Parts Breakdown REMOTE-READY Models Parts ListTHERMOSTAT-CONTROLLED Blower KIT GA3450T AccessoriesEquipment Shutoff Valve GA5010 Perimeter Trim KIT GA6095Information Video Receiver and HAND-HELD Thermostat Remote Control KIT GhrctbReceiver and HAND-HELD Remote Control KIT Ghrcb Cabinet Mantel and Full Hearth BasePage Page Limited Warranty VENT-FREE Compact Classic Hearth Fireplace Warranty InformationKeep this Warranty
Top Page Image Contents