Continental BCDV42N, BCDV42P manual Direct Vent Millivolt System

Page 1
DIRECT VENT MILLIVOLT SYSTEM

INSTALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS, CSA 2.33, ANSI Z21.88 FOR VENTED GAS FIREPLACE HEATERS

DIRECT VENT MILLIVOLT SYSTEM

INSTALLATION AND OPERATION INSTRUCTIONS FOR

VENTED GAS FIREPLACE HEATER

NATURAL GAS MODEL BCDV42N

PROPANE GAS MODEL BCDV42P

CERTIFIED FOR CANADAAND UNITED STATES USING ANSI / CSA METHODS

WARNING: If the information in these instructions is not followed exactly, a fire or

explosion may result causing property damage, personal injury or death.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapours and liquids in the vicinity

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Immediately call your gas supplier from

• Do not touch any electrical switch.

a neighbour's phone. Follow the gas

• Do not use any phone in your build-

supplier's instructions.

ing.

• If you cannot reach your gas supplier,

 

call the fire department.

Installation and service must be performed by a qualified installer, service agency

or the gas supplier.

Manual background R-2000 Manual background

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 4Y8 Canada • (705)721-1212fax(705)722-6031

www.continentalfireplaces.com • ask@continentalfire.com

W415-0385 / A / 10.02.03

Image 1
Contents DIRECT VENT MILLIVOLT SYSTEM PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE TABLE of CONTENTS13 - 18 INSTALLATION 21 OPTIONAL BLOWER INSTALLATIONAny labour related to warranty repair is not covered CONTINENTAL GAS FIREPLACE PRESIDENTS LIFETIME LIMITED WARRANTYISO 9001 2000 Quality Assurance Certificate CONDITIONS AND LIMITATIONSGENERAL INFORMATION GENERAL INSTRUCTIONSCARE OF GLASS, AND PLATED PARTS VENTING LENGTHS VENTINGINSTALLATIONS AIR TERMINAL INSTALLATIONSA B C D E F G H I J K L M N O CANADIAN 12 INCHES 12 INCHES 12 INCHES 32 INCHES 32 INCHES 0 INCHESSPECIAL VENT INSTALLATIONS TYPICAL VENT INSTALLATIONSPERISCOPE TERMINATION FIGURES 3 a-cHORIZONTAL TERMINATION VENTING APPLICATION FLOW CHARTVERTICAL TERMINATION DEFINITIONS HORIZONTAL TERMINATIONELBOW VENT LENGTH VALUES Formula 1 HT VT Formula 2 HT + VT 40 feet ExampleFormula 1 HT 4.2 VT ExampleFormula 2 HT + VT 24.75 feet Formula 1 HT 4.2 VT Formula 2 HT + VT 24.75 feetFormula 1 HT VT Formula 2 HT + VT 40 feet VERTICAL TERMINATIONFIGURE10 REQUIRED VERTICAL RISE IN FEET VT Formula 1 HT 3VT Formula 2 HT + VT 40 feet ExampleHORIZONTAL VENT RUN PLUS OFFSET IN FEET HT HORIZONTAL INSTALLATION INSTALLATION WALL AND CEILING PROTECTIONVERTICAL INSTALLATION HORIZONTAL AIR TERMINAL INSTALLATION USING FLEXIBLE VENT COMPONENTSVERTICAL AIR TERMINAL INSTALLATION Use only approved aluminum flexible liner kits markedEXTENDED HORIZONTAL AIR TERMINAL INSTALLATION USING RIGID VENT COMPONENTSFIREPLACE VENT CONNECTION GAS INSTALLATION VERTICAL VENTING INSTALLATIONProceed once the vent installation is complete 1. Move the fireplace into position and secure using theFRAMING MOBILE HOME INSTALLATIONFIGURES MANTLE INSTALLATION NAILING TAB INSTALLATIONAdditional set screws may be installed NAILINGL42 LOUVRE INSTALLATION FINISHINGLOGO PLACEMENT PORCELAIN REFLECTIVE PANELSLOG PLACEMENT #2#3CHARCOAL EMBERS VERMICULITEB AC OPTIONAL BLOWER INSTALLATIONGD36 THERMOSTATIC SENSOR CONTROL OPTIONAL FAN INSTALLATIONTo safely install the fan, turn off the electricity first MAINTENANCE OPERATION / MAINTENANCEFOR YOUR SAFETY READ BEFORE LIGHTING Turn off the gas and electrical power before servicing the fireplacePILOT BURNER ADJUSTMENT ADJUSTMENTSVENTURI ADJUSTMENT Air shutter adjustment must only be done by a qualified installerACCESSORIES REPLACEMENTSREPLACEMENT PARTS GD420 5 FTW415-0385 / A SYMPTOM TROUBLE SHOOTING GUIDEPROBLEM TEST SOLUTIONTOLI