Continental BCDV42P TABLE of CONTENTS, Please Retain This Manual For Future Reference, Finishing

Page 2
TABLE of CONTENTS

2

TABLE of CONTENTS

PG 2-4 INTRODUCTION

Warranty

General Instructions

General Information

Care of Glass & Plated Parts

5 - 12 VENTING

Venting Lengths

Air Terminal Locations

Typical Vent Installations

Special Vent Installations

Venting Application Flow Chart

Venting Specifications

13 - 18 INSTALLATION

Wall and Ceiling Protection

Using Flexible Vent Components

Fireplace Vent Connection

Using Rigid Vent Components

Restricting Vertical Vents

Gas Installation

Mobile Home Installation

Framing

Nailing Tab Installation

Mantle Installation

19-20 FINISHING

Louvre Installation

Logo Placement

Porcelain Reflective Panels

Log Placement / Glowing Embers

Charcoal Embers

Vermiculite

Charcoal Lumps

21OPTIONAL BLOWER INSTALLATION

22OPTIONAL FAN INSTALLATION / GD36THERMOSTATICSENSORCON- TROL

23OPERATION / MAINTENANCE

Operating Instructions

Maintenance

24 ADJUSTMENTS

Pilot Burner Adjustment

Venturi Adjustment

25-26 REPLACEMENTS

Ordering Replacement Parts

Replacement Parts

Vent Kits

Terminal Kits

Accessories

27-28 TROUBLE SHOOTING GUIDE

PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE

WARNING

Do not burn wood or other materials in this fireplace.

Adults and especially children should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition. Supervise young children when they are in the same room as the fireplace.

Due to high temperatures, the fireplace should be located out of traffic and away from furniture and draper- ies.

Clothing or other flammable material should not be placed on or near the fireplace.

Any safety screen or guard removed for servicing must be replaced prior to operating the fireplace.

It is imperative that the control compartments, burners and circulating blower and its passageway in the fireplace and venting system are kept clean. The fireplace and its venting system should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. The fireplace area must be kept clear and free from combustible materials, gasoline and other flammable vapours and liquids.

Under no circumstances should this fireplace be modified.

This fireplace must not be connected to a chimney flue pipe serving a separate solid fuel burning appliance.

Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect the fireplace and to replace any part of the control system and any gas control which has been under water.

Do not operate the fireplace with the glass door removed, cracked or broken. Replacement of the glass should be done by a licensed or qualified service person. Use only with a glass door certified with the fireplace.

Do not strike or slam shut the fireplace glass door.

This fireplace uses and requires a fast acting thermocouple. Replace only with a fast acting thermocouple supplied by Wolf Steel Ltd.

NOTE: changes, other than editorial, are denoted by a vertical line in the margin.

W415-0385 / A / 10.02.03

Image 2
Contents DIRECT VENT MILLIVOLT SYSTEM 13 - 18 INSTALLATION TABLE of CONTENTSPLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE 21 OPTIONAL BLOWER INSTALLATIONISO 9001 2000 Quality Assurance Certificate CONTINENTAL GAS FIREPLACE PRESIDENTS LIFETIME LIMITED WARRANTYAny labour related to warranty repair is not covered CONDITIONS AND LIMITATIONSCARE OF GLASS, AND PLATED PARTS GENERAL INSTRUCTIONSGENERAL INFORMATION VENTING VENTING LENGTHSA B C D E F G H I J K L M N O AIR TERMINAL INSTALLATIONSINSTALLATIONS CANADIAN 12 INCHES 12 INCHES 12 INCHES 32 INCHES 32 INCHES 0 INCHESPERISCOPE TERMINATION TYPICAL VENT INSTALLATIONSSPECIAL VENT INSTALLATIONS FIGURES 3 a-cVERTICAL TERMINATION VENTING APPLICATION FLOW CHARTHORIZONTAL TERMINATION ELBOW VENT LENGTH VALUES HORIZONTAL TERMINATIONDEFINITIONS Formula 1 HT VT Formula 2 HT + VT 40 feet ExampleFormula 2 HT + VT 24.75 feet ExampleFormula 1 HT 4.2 VT Formula 1 HT 4.2 VT Formula 2 HT + VT 24.75 feetFIGURE10 VERTICAL TERMINATIONFormula 1 HT VT Formula 2 HT + VT 40 feet HORIZONTAL VENT RUN PLUS OFFSET IN FEET HT Formula 1 HT 3VT Formula 2 HT + VT 40 feet ExampleREQUIRED VERTICAL RISE IN FEET VT VERTICAL INSTALLATION INSTALLATION WALL AND CEILING PROTECTIONHORIZONTAL INSTALLATION VERTICAL AIR TERMINAL INSTALLATION USING FLEXIBLE VENT COMPONENTSHORIZONTAL AIR TERMINAL INSTALLATION Use only approved aluminum flexible liner kits markedFIREPLACE VENT CONNECTION USING RIGID VENT COMPONENTSEXTENDED HORIZONTAL AIR TERMINAL INSTALLATION Proceed once the vent installation is complete VERTICAL VENTING INSTALLATIONGAS INSTALLATION 1. Move the fireplace into position and secure using theFIGURES MOBILE HOME INSTALLATIONFRAMING Additional set screws may be installed NAILING TAB INSTALLATIONMANTLE INSTALLATION NAILINGLOGO PLACEMENT FINISHINGL42 LOUVRE INSTALLATION PORCELAIN REFLECTIVE PANELSCHARCOAL EMBERS #2#3LOG PLACEMENT VERMICULITEOPTIONAL BLOWER INSTALLATION B ACTo safely install the fan, turn off the electricity first OPTIONAL FAN INSTALLATIONGD36 THERMOSTATIC SENSOR CONTROL FOR YOUR SAFETY READ BEFORE LIGHTING OPERATION / MAINTENANCEMAINTENANCE Turn off the gas and electrical power before servicing the fireplaceVENTURI ADJUSTMENT ADJUSTMENTSPILOT BURNER ADJUSTMENT Air shutter adjustment must only be done by a qualified installerREPLACEMENT PARTS REPLACEMENTSACCESSORIES GD420 5 FTW415-0385 / A PROBLEM TROUBLE SHOOTING GUIDESYMPTOM TEST SOLUTIONTOLI